BrandSafway SPIDER GLAZIER 2200 Manuel utilisateur

Manufactured by: SafeWorks | 365 Upland Drive, Seattle, WA 98188 | Phone: (877) 774-3370 | Fax: (206) 575-6240

Email: [email protected] | Website: SpiderStaging.com

703739-1 Revision D Spider Glazier 2200 Operator's Manual Issue Date: 2019-Jan-25

OPERATOR’S MANUAL

SPIDER GLAZIER 2200

703739-1 Revision D Spider Glazier 2200 Operator's Manual Issue Date: 2019-Jan-25Page 2 of 27

WARNING

• All persons operating this equipment must read and completely understand this manual.

• All persons must be thoroughly trained in the use of this equipment, its operational and safety features, and

they must also be capable of carrying out the daily inspections.

• Only authorized persons shall operate this equipment.

• Any operation in violation of these instructions is at the operator’s own risk and may result in serious

injuries.

• Keep this manual with the equipment at all times.

• Use only spare parts and recommended steel wire rope from Spider®.

• It is the responsibility of the user to determine that this equipment is suitable to be used in conjunction with

any other equipment.

• It is the responsibility of the user to determine whether this equipment, and all other components used with it,

will be in conformity with the provisions of federal, state, and local ordinances and regulations.

703739-1 Revision D Spider Glazier 2200 Operator's Manual Issue Date: 2019-Jan-25 Page 3 of 27

Table of Contents

 

a) Instructions for Safe Operation..................................................................................................................5

 

a) 1926 Subpart C: General Safety and Health Provisions, Standard 1926.20: General Safety and Health

Provisions...................................................................................................................................................6

b) 1926 Subpart C: General Safety and Health Provisions, Standard 1926.21 Safety Training and

Education ...................................................................................................................................................6

c) 1926 Subpart C: General Safety and Health Provisions, Standard 1926.28: Personal Protective

Equipment..................................................................................................................................................7

d) 1926 Subpart E: Personal Protective and Life Saving Equipment, Standard 1926.104: Safety Belts,

Lifelines, and Lanyards..............................................................................................................................7

e) 1926 Subpart H: Materials Handling, Storage, Use, and Disposal, Standard 1926.251: Rigging

Equipment for Material Handling..............................................................................................................8

f) 1926 Subpart M: Fall Protection, Standard 1926.501: Duty to have Fall Protection ................................8

g) 1926 Subpart N: Helicopters, Hoists, Elevators, and Conveyors, Standard 1926.552: Material Hoists,

Personnel Hoists, and Elevators.................................................................................................................8

h) 1926 Subpart R: Steel Erection, Standard 1926.760: Fall Protection........................................................9

 

a) Features of the Spider Glazier 2200.........................................................................................................10

b) Parts of the Spider Glazier 2200 ............................................................................................................. 11

 

a) Attaching Steering Handle.......................................................................................................................12

b) Installing Backspan..................................................................................................................................13

c) Angle Brace Installation ..........................................................................................................................14

d) Outreach Installation................................................................................................................................15

e) Counterweight Installation.......................................................................................................................16

f) Installing Tieback Locking Device ..........................................................................................................17

g) Using a Tieback........................................................................................................................................18

h) Hoist Installation......................................................................................................................................19

i) Wire Winder and Overspeed Safety Device Installation..........................................................................20

j) Reeving ....................................................................................................................................................21

 

 ...................................................................................................................................23

 ..............................................................................................................................24

Continued on next page C

703739-1 Revision D Spider Glazier 2200 Operator's Manual Issue Date: 2019-Jan-25Page 4 of 27

 

 ...............................................................................................25

 

a) Important Points to Note..........................................................................................................................26

b) 30-Day Inspection....................................................................................................................................26

Wire Rope Inspection Report ........................................................................................................................27

Table of Contents (Continued)

703739-1 Revision D Spider Glazier 2200 Operator's Manual Issue Date: 2019-Jan-25 Page 5 of 27

1. SAFETY

 

Before using the Spider Glazier 2200, learn the procedures described in this manual. Any operation in violation

of these instructions may result in bodily injury or death.

Every year, workers are injured, become disabled, or are killed because of carelessness or

because they did not understand how to correctly operate the equipment they were using. Do

not become one of them. Know how to use this equipment and prevent accidents.

NEVER operate equipment that you do not understand. You may cause accidents, resulting in

injury or death to you or people around you.

This instruction manual is not all inclusive. It is impossible to anticipate every conceivable way this equipment

may be used, or every hazardous situation. It is very important that you determine for yourself whether the

situation is safe. You must understand the operating characteristics of both the hoist and gantry. You must

understand how the equipment will operate in your application. Before use, you must be certain you are not

creating a situation that may endanger yourself or others, or cause damage to property. Call your supplier if

you have any questions concerning this equipment.

1. Read and understand this manual  using this equipment.

2. Additional copies of this manual are available from your Spider operations center. It is the duty of the

employer to provide each operator with a copy of this manual.

3. Setup and use must comply not only with the instructions in this manual but also with federal

OSHA 29 CFR standards, as well as applicable state and local codes in force at the location of

application. It is the user’s responsibility to review applicable state or local codes or regulations

pertaining to general safety or use of this equipment, and it is the user’s responsibility to resolve any



4. The Spider Glazier 2200 is designed to be assembled by a minimum of three workers and typically

operated by three: a loader (on the lowest level), a positioner (who operates the remote from an

intermediary level above the loader) and a spotter (stationed at the hoist on the top level).

5. The Spider Glazier 2200 is designed to lift a maximum load of 2,000 lb. 





6. Secure the foot-operated caster brakes before loading counterweights. The caster brakes are designed

to maintain the position of the Spider Glazier 2200 on a level surface. 

Glazier 2200 on a slope.

7. The Spider Glazier 2200 is powered by a DualLift M1009 material handling hoist, which is NOT rated

for manlifting. 

8. Do NOT allow personnel in the hoistway or within 10 feet on either side of it. Clearly mark and



703739-1 Revision D Spider Glazier 2200 Operator's Manual Issue Date: 2019-Jan-25Page 6 of 27

2. 

Selected portions of OSHA Code of Federal Regulations Title 29 have been reproduced in this section for the

convenience of Spider Glazier 2200 users. Spider assumes no responsibility for the accuracy, completeness, or



of Labor.

 





1. Section 107 of the Act requires that it shall be a condition of each contract which is entered into





that no contractor or subcontractor for any part of the contract work shall require any laborer or

mechanic employed in the performance of the contract to work in surroundings or under working

conditions which are unsanitary, hazardous, or dangerous to his health or safety.



1. It shall be the responsibility of the employer to initiate and maintain such programs as may be

necessary to comply with this part.

2. Such programs shall provide for frequent and regular inspections of the job sites, materials, and

equipment to be made by competent persons designated by the employers.

3. The use of any machinery, tool, material, or equipment that is not in compliance with any

applicable requirement of this part is prohibited. Such machine, tool, material, or equipment shall



be physically removed from its place of operation.

4. 

equipment and machinery.

 





1. The Secretary shall, pursuant to Section 107(f) of the ACT, establish and supervise programs

for the education and training of employers and employees in the recognition, avoidance and

prevention of unsafe conditions in employments covered by the act.

703739-1 Revision D Spider Glazier 2200 Operator's Manual Issue Date: 2019-Jan-25 Page 7 of 27



1. The employer should avail himself of the safety and health and training programs the Secretary

provides.

2. The employer shall instruct each employee in the recognition and avoidance of unsafe conditions

and the regulations applicable to his work environment to control or eliminate any hazards or

other exposure to illness or injury.

3. Employees required to handle or use poisons, caustics, and other harmful substances shall be

instructed regarding the safe handling and use, and be made aware of the potential hazards,

personal hygiene, and personal protective measures required.

 



(a) The employer is responsible for requiring the wearing of appropriate personal protective equipment in

all operations where there is an exposure to hazardous conditions or where this section indicates the

need for using such equipment to reduce hazards to employees.

(b) Regulations governing the use, selection, and maintenance of personal protective and lifesaving

equipment are described under Subpart E below.

 



(a) Lifelines, safety belts, and lanyards shall be used only for employee safeguarding. Any lifeline, safety

belt, or lanyard actually subjected to in-service loading, as distinguished from static load testing, shall

be immediately removed from service and shall not be used again for employee safeguarding.

(b) Lifelines shall be secured above the point of operation to an anchorage or structural member

supporting a minimum dead weight of 5,400 lb.





be used.



provide for a fall of no greater than 6 feet. The rope shall have a nominal breaking strength of 5,400

lb.

(e) All safety belt and lanyard hardware shall be dropped forged or pressed steel, cadmium plated in



shall be smooth and free of sharp edges.

(f) All safety belt and lanyard hardware, except rivets, shall be capable of withstanding a tensile loading

of 4,000 pounds without cracking, breaking, or permanently deforming.

703739-1 Revision D Spider Glazier 2200 Operator's Manual Issue Date: 2019-Jan-25Page 8 of 27

 





1. Rigging equipment for material handling shall be inspected prior to use on each shift and as

necessary during its use to ensure that it is safe. Defective rigging equipment shall be removed

from service.

2. Employers must ensure that rigging equipment:

i. 

manufacturer that indicate the recommended safe working load;

ii. Not be loaded in excess of its recommended safe working load as prescribed on the



iii.

of this section.

 



 

leading edges are under construction, but who is not engaged in the leading edge work, shall be

protected from falling by a guardrail system, safety net system, or personal fall arrest system. If a

guardrail system is chosen to provide the fall protection, and a controlled access zone has already

been established for leading edge work, the control line may be used in lieu of a guardrail along

the edge that parallels the leading edge.

3. Each employee in a hoist area shall be protected from falling 6 feet (1.8 m) or more to lower

levels by guardrail systems or personal fall arrest systems. If guardrail systems, [or chain, gate, or

guardrail] or portions thereof, are removed to facilitate the hoisting operation (e.g., during landing

of materials), and an employee must lean through the access opening or out over the edge of the

access opening (to receive or guide equipment and materials, for example), that employee shall be

protected from fall hazards by a personal fall arrest system.

 





2. Rated load capacities, recommended operating speeds, and special hazard warnings or

instructions shall be posted on cars and platforms.

3. Wire rope shall be removed from service when any of the following conditions exists:

i. In hoisting ropes, six randomly distributed broken wires in one rope lay or three broken

wires in one strand in one rope lay;



original diameter of the outside wires;

703739-1 Revision D Spider Glazier 2200 Operator's Manual Issue Date: 2019-Jan-25 Page 9 of 27

iii.Evidence of any heat damage resulting from a torch or any damage caused by contact with

electrical wires;

iv. Reduction from nominal diameter of more than three sixty-fourths inch for diameters

up to and including three-fourths inch; one-sixteenth inch for diameters seven-eights to





1. i. Operating rules shall be established and posted at the operator’s station of the hoist. Such

rules shall include signal system and allowable line speed for various loads. Rules and

notices shall be posted on the car frame or crosshead in a conspicuous location, including the

 

ii. No person shall be allowed to ride on material hoists except for the purposes of inspection

and maintenance.

 



1. Except as provided by paragraph (a)(3) of this section, each employee engaged in a steel erection



(4.6 m) above a lower level shall be protected from fall hazards by guardrail systems, safety net

systems, personal fall arrest systems, positioning device systems or fall restraint systems.



3. Be provided, at heights over 15 and up to 30 feet above a lower level, with a personal fall arrest

system, positioning device system or fall restraint system and wear the equipment necessary to be



with paragraph (a)(1) of this section.

703739-1 Revision D Spider Glazier 2200 Operator's Manual Issue Date: 2019-Jan-25Page 10 of 27

3. 

The Spider Glazier 2200 is used to lift and position curtain wall panels for installation. 



 

Feature Function 

230 V, 60 Hz, 16 A Dual Lift M1009

Material Handling Hoist

• Maximum rated load is 2,000 lb.

• Variable Frequency Drive for speeds





• Overspeed Safety Device.

• Allows single line operation to

2,000 lb.

• Variable Frequency Drive



power supply.

Pendant or Wireless Remote Control • 8 ft cord.

• Optional multiple wireless pendants.

• Emergency stop on both types of

remote control.

• Easy monitoring of emergency

stop.

• Allows operation of hoist from

multiple locations.

Adjustable Front Sheave Position • Front sheave height manually adjusts

by repositioning the outreach to one of





• Front sheave can be positioned at

18 in., 33 in., and 48 in. from leading

edge of front gantry base.

• Flexible.

• Easy to position.

Adjustable Tieback • Uses reliable, secure, Dual Lift

Inclination Safety Lock suspended

from shackle with sling link.

• Locks securely.

• Easy to position and reposition.

Heavy-Duty Dual-Lock Casters • Pin-activated Swivel Locks keep

casters in one of four positions.

• Step-on Wheel Locks prevent casters

from rolling.

• Easy to position.

• Easy to lock in place.

Stowable Outreach • Footprint in stowed position is 12 ft.

long x 4 ft. wide x 6 ft. 7 in. tall.

• Fits in standard construction

elevator.

• Easy transportation to job site.

Top Limit Switch • Striker plate below front sheave

opens shrouded switch at angle

tangent to sheave.

• Stops upward travel of load.

• Activates hoist overload safety

so load can be lowered.

• Prevents sheave damage.

 • Maximum downward reach is 300 ft.

from bottom of front sheave.

• Wire winder attached to hoist.

• Allows single line operation to

2,000 lb.

• Meets ANSI 7:1 safety factor.

Uses Standard Spider

Counterweights

• Space for 50 x 50-lb counterweights

(largest capacity of counterweights

required is 2,420 lb).

• Easy to stagger-stack to

minimize pinch points.

• Readily available from Spider

service centers.

Table des matières

Autres manuels BrandSafway Système de levage

BrandSafway

BrandSafway Spider SC1000 Series Manuel utilisateur

Manuels Système de levage populaires d'autres marques

morse

morse 82H-124 Manuel utilisateur

Braun

Braun NL955 Series Manuel utilisateur

haacon

haacon 1889.10 Manuel utilisateur

Protekt

Protekt AT 252 Manuel utilisateur

R. Beck Maschinenbau

R. Beck Maschinenbau HS 600 Manuel utilisateur

Nova Technology International, LLC

Nova Technology International, LLC NAS Series Manuel utilisateur

Genie

Genie Z-60/34 Manuel utilisateur

Screen Technics

Screen Technics INTERFIT Vertical Up Lift Manuel utilisateur

Mortuary Lift

Mortuary Lift ULTIMATE 1000 Manuel utilisateur

Custom Equipment

Custom Equipment Hy-Brid 3 Series Manuel de programmation

Custom Equipment

Custom Equipment Hy-Brid Lifts 2 Series Manuel de programmation

Hy-Brid Lifts

Hy-Brid Lifts HB-P3.6 Manuel de programmation

BERG

BERG BeNomic EasyLeaf Manuel utilisateur

Powermate

Powermate LiftGate LG-3 Manuel utilisateur

Snorkel

Snorkel TM12 Series Manuel utilisateur

Terberg

Terberg OMNIDEKA Manuel utilisateur

Harmar Mobility

Harmar Mobility AL625 Mode d'emploi

Rotary

Rotary SPO16 Manuel utilisateur