BrandMotion 9002-9521 Manuel utilisateur

INSTALLATION INSTRUCTIONS

9521 Instructions 2-12-15.doc 1 of 35

Rear Vision System – Tailgate Handle Camera Mirror Display

2004-2014 Ford F-150 and 2008-2015 Ford Super Duty

(Kit part numbers 9002-9521)

Kit Contents:

Tools Required:

Mirror

Tailgate Handle with camera and harness

Interior (shorter) Harness

Chassis (longer) Harness

2 Foam pieces (if needed and optional)

1 bag containing:

25 Wire Ties (short)

7 pairs of T-taps (optional)

(Splice, solder & heat shrink

recommended.)

Z-Tech (in a white bottle)

1 bag containing:

2 Templates (along with these instructions)

2 Wire Ties (long and optional)

T20 and T30 Torx Drivers

8mm and 10mm Sockets

Flat Blade Screwdriver

Phillips Screwdriver

Plastic Trim Removal tool

Drill Bit

1 inch Center Hole Saw

Soldering Iron

Small brush

Round file (if needed)

Mirror removal tool # OTC8200

(Required for non-screw type mirrors)

Deburring Tool

Electrical Tape or Heat Shrink

NOTE: We strive to provide accurate and up-to-date installation instructions. For the latest full

color instructions, as well as an installation video, please visit www.brandmotion.com

Preparation

•Ensure all lamps and accessories are OFF.

•Ensure the ignition switch is in the OFF position.

•Loosen the negative battery cable bolt. Remove negative battery cable from terminal and position away

from battery.

•Wait one (1) minute prior to working on the vehicle to assure airbag system has been disabled for your

safety.

PRE-INSTALLATION VEHICLE CHECKLIST

Before beginning, determine how the vehicle is equipped and check appropriate boxes:

Start vehicle and note location of compass display. Unplug mirror connector from back of mirror.

•If compass display on the dash shows (- -) the compass module must be relocated (refer to Section 6).

Determine whether the vehicle has an opening in the center of pickup bed close to opposite of the opening in

the bottom of the tailgate.

□Yes, skip Section 1.

□No, tailgate must be removed to drill an opening for the camera harness

(refer to Section 1).

□Vehicle does NOT have an auto dimming inside mirror (refer to Section 7).

Determine the connector style used on the existing inside rearview mirror:

7-pin or 16-pin. For past models additional information, please see Section 10B (reference).

□Check kit contents are complete against the list above.

INSTALLATION INSTRUCTIONS

9521 Instructions 2-12-15.doc 2 of 35

TABLE OF CONTENTS

Pages

Section 1: Cut Pickup Bed Opening (if required)

Section 2: Install Camera

Section 3: Modify Rain Sensor (if equipped)

Section 4: Remove Mirror

Section 5: Install Interior Harness

6-7

Section 6: Wire Interior Harness

6A: Remove compass circuit board (if required)

6B: Wiring for vehicles with 7-pin mirror connector

6C: Wiring for vehicles with 16-pin mirror connector

6D: Relocate compass circuit board (if required)

Section 7: Wiring Required for Inside Mirrors without Auto

Dimming (if required)

12-16

Section 8: Install Supplied Mirror

Section 9: Install Chassis Harness

18-21

Section 10: Reference

10A: Supplied Harness Pinouts

10B: Previous Model Year Mirror Connector Pinouts

23-24

10C: Previous Model Year Ignition & Reverse Locations

25-32

10D: Relocating the Compass Circuit Board for

Vehicles with External Compass Module (if required)

33-34

10E: Vehicles with Sync Microphone in Mirror (if equipped)

INSTALLATION INSTRUCTIONS

9521 Instructions 2-12-15.doc 3 of 35

Section 1: Cut Pickup Bed Opening

Follow Steps 1 through 4 only if the vehicle does not have an opening in the bed above

the license plate per Figure 1

Figure 1

1. Prepare a clean, flat work surface for tailgate.

Remove tailgate retaining straps with a screwdriver.

With an assistant, remove the tailgate by lifting away

from lower tension pins, and set tailgate aside.

2. Measure 21 inches from the left edge and 1¼inches

from the top and make a temporary mark on the

pickup bed (Figure 2).

Figure 2

3. Center punch the mark and drill a pilot hole. Next, cut

a 1/2 inch opening with a hole saw (Figure 3).

Figure 3

4. Clean the rough edges of the opening with a

deburring tool. Apply supplied Z-tech with a small

brush (Figure 4). Reinstall tailgate.

Figure 4

INSTALLATION INSTRUCTIONS

9521 Instructions 2-12-15.doc 4 of 35

Section 2: Install Camera

5. Remove tailgate handle by loosening two nuts with a

10mm socket (Figure 5).

Figure 5

6. Remove lock cylinder from tailgate handle by pulling

out wire spring clip (Figure 6).

Figure 6

7. Install lock cylinder into supplied tailgate camera

handle with by pushing cylinder into handle. Secure

the cylinder with the wire spring clip.

8. Route camera harness through handle opening in

tailgate to the hole in the bottom of the tailgate

(Figure 7).

Figure 7

9. Install supplied tailgate handle camera into tailgate

by tightening two nuts with 10mm socket (Figure 8).

Figure 8

INSTALLATION INSTRUCTIONS

9521 Instructions 2-12-15.doc 5 of 35

Section 3: Modify Rain Sensor

(If equipped)

Follow Steps 10 and 12 on this page

only if you have a rain sensor module

mounted on your inside rear view

mirror.

10. Remove rain sensor by pulling down and remove

connector (Figure 10).

Figure 10

11. Using a round file, open up the rain sensor

opening for mirror by 0.46mm so the supplied

mirror fits (Figure 11).

Figure 11

Section 4: Remove Mirror

12. If you did not already do so previously, start the

vehicle and note location of compass display. Unplug

the mirror connector from mirror (Figure 12).

Figure 12

13. If the compass display on the dash shows (- -) the

compass module must be relocated. This operation

is described in Section 6.

14. Loosen the screw that attaches the existing rear view

mirror to the windshield mounting button with a T20

Torx driver (Figure 13).

CAUTION: Removing the mirror from the windshield can

cause damage to the windshield. It is highly

recommended to contact either a Ford dealership

or a windshield replacement company. Otherwise,

slide the mirror upwards and towards the rear to remove

it from the windshield (Figure 13).

Figure 13

NOTE: On some models without screws, Mirror

Removal Tool # OTC8200 is required.

INSTALLATION INSTRUCTIONS

9521 Instructions 2-12-15.doc 6 of 35

Section 5: Install Interior Harness

15. Remove driver side dash panel end cap by pulling

away weather-stripping and pull end panel to

release clips from the dash panel (Figure 14).

Figure 14

16. Remove driver side A-pillar by pulling with hands to

release clips from sheet metal (Figure 15).

Figure 15

17. Remove both sun visor anchors (either side of roof

console) by removing one screw with a Phillips

screwdriver (Figure 16).

Figure 16

18. Remove roof console with hands to remove the clips

from the sheet metal. Then remove both connectors

(Figure 17).

Figure 17

19. Route the supplied interior harness under leading

edge of the driver side headliner by gently

separating the headliner from the windshield and

tucking the harness into the gap with your fingers

(Figure 18).

Figure 18

20. Route the supplied interior harness down the driver

side A-pillar (Figure 19).

Figure 19

INSTALLATION INSTRUCTIONS

9521 Instructions 2-12-15.doc 7 of 35

Section 5: Install Interior Harness continued

21. Route the supplied interior harness through the dash

(Figure 20).

Figure 20

INSTALLATION INSTRUCTIONS

9521 Instructions 2-12-15.doc 8 of 35

Section 6A: Remove the Compass Circuit Board (if required)

Follow the steps in Section 6A only if your compass displayed (- -) when the mirror

connector was unplugged in Section 4.

22. Pry mirror apart with a screwdriver (Figure 21).

Figure 21

23. Remove the circuit board from the mirror by

disengaging both connectors. Mark the top of the

circuit board with a permanent marker to insure

proper plug connection later (Figure 22).

Figure 22

24. Wrap the mirror circuit board in the supplied foam

pieces, and cut an opening for the connector

terminals (Figure 23).

Figure 23

25. Make sure ignition is off. Remove the original vehicle

mirror harness connector by cutting the harness

wires 2 inches from the connector. Cut wires one at

a time and strip the insulation from each as these

will be spliced to the supplied interior harness.

INSTALLATION INSTRUCTIONS

9521 Instructions 2-12-15.doc 9 of 35

Section 6B: Wiring vehicles with 7-pin mirror connector

26. On the supplied interior harness, locate the seven

loose wires near the black 16-pin connector (Figure

24)

Figure 24

27. Consulting the Connector C911 pinout diagram

opposite, splice the seven wires to the vehicle mirror

harness wires according to Diagram A1.

Diagram A1

Supplied

Interior

Harness

Wire Color

Polarity

Function

Splice to

Wire at

C911

Location

Red

Ignition

pin 1

Green

Reverse

pin 2

Black

Ground

pin 3

Yellow

Compass

pin 7

Pink

Compass

pin 6

Orange

Auto Dimming

Mirror

pin 4

White

Auto Dimming

Mirror

pin 5

28. If you removed the compass circuit board, per

section 6A: On the supplied interior harness, locate

the five loose wires near the white 6-pin connector.

(Figure 25)

Figure 25

29. Consulting the Connector C911 pinout diagram

below, splice the five pink, green, black, red, and

yellow wires to the vehicle mirror harness connector

according to Diagram A1.

30. If you did not remove the compass circuit board,

isolate the five unused loose wires with electrical

tape.

NOTE: Circuit colors

shown may vary

depending on

model and year.

Verify pin locations

and check circuit for

proper function

using a digital volt-

ohm meter.

IMPORTANT: If reverse signal does not exist in pin

2 of 7-pin mirror C911 connector (see diagram

below), then follow directions in Section 7 to connect

reverse.

INSTALLATION INSTRUCTIONS

9521 Instructions 2-12-15.doc 10 of 35

Section 6C: Wiring for vehicles with 16-pin mirror connector

31. On the supplied interior harness, near the black 16

pin connector, locate the seven loose wires. (Figure

24)

32. Isolate the pink wire with electrical tape as it will not

be used.

33. Using the Connector C9039 pinout diagram opposite,

splice the remaining six wires to the vehicle mirror

harness wires according to Diagram A2.

Diagram A2

Supplied

Interior

Harness

Wire Color

Polarity

Function

Splice to

Wire at

C9039

Location

Red

Ignition

pin 1

Green

Reverse

pin 9

Black

Ground

pin 4

Yellow

pin 2

(if present)

Pink

Not used –

Isolate with

electrical tape

Orange

Auto Dimming

Mirror

pin 11

White

Auto Dimming

Mirror

pin 15

34. If you removed the compass circuit board, per

section 6A: On the supplied interior harness, locate

the five loose wires near the white 6-pin connector.

(Figure 25)

35. IMPORTANT: Isolate the red wire with electrical tape

as it will not be used.

36. Using the Connector C9039 pinout diagram opposite,

splice the remaining four red, green, black, and

yellow wires to the vehicle mirror harness connector

removed in Step 24 according to Diagram A2.

37. If you did not remove the compass circuit board,

isolate the five loose wires with electrical tape, as

they will not be used.

NOTE: Circuit colors

shown may vary

depending on model

and year. Verify pin

locations and check

circuit for proper

function using a digital

volt-ohm meter.

IMPORTANT: If reverse signal does not exist

in pin 9 of 16-pin mirror C9039 connector (see

diagram below), then follow directions in

Section 7 to connect reverse.

Table des matières

Autres manuels BrandMotion Accessoires automobiles

BrandMotion

BrandMotion FLTW-7511 Manuel utilisateur

BrandMotion

BrandMotion AVMS-3690 Manuel utilisateur

BrandMotion

BrandMotion 1009-6503 Manuel utilisateur

BrandMotion

BrandMotion F Series Manuel utilisateur

BrandMotion

BrandMotion 9002-7692v2 Manuel utilisateur

BrandMotion

BrandMotion 9002-2775v1 Manuel utilisateur

BrandMotion

BrandMotion 9002-8817 Manuel utilisateur

BrandMotion

BrandMotion 9002-8838 Manuel utilisateur

BrandMotion

BrandMotion 9002-7710 Manuel utilisateur

BrandMotion

BrandMotion AVMS-3701v2 Manuel utilisateur

BrandMotion

BrandMotion 9002-8846 Manuel utilisateur

BrandMotion

BrandMotion 9002-7803 Manuel utilisateur

BrandMotion

BrandMotion FLTW-7692V3 Manuel utilisateur

BrandMotion

BrandMotion FVMR-1000 Manuel utilisateur

BrandMotion

BrandMotion 9002-7701 Manuel utilisateur

BrandMotion

BrandMotion ADAS-1000V3 Manuel utilisateur

BrandMotion

BrandMotion AVMS-3701v3 Manuel utilisateur

BrandMotion

BrandMotion FLEETWORKS FLTW-7610 Manuel utilisateur

BrandMotion

BrandMotion 9002-7702 Manuel utilisateur

BrandMotion

BrandMotion 9002-7601 Manuel utilisateur

BrandMotion

BrandMotion 5000-8750 Manuel utilisateur

BrandMotion

BrandMotion 9002-9516 Manuel utilisateur

BrandMotion

BrandMotion FLEETWORKS FLTW-7611 Manuel utilisateur

BrandMotion

BrandMotion 9002-2911 Manuel utilisateur

Manuels Accessoires automobiles populaires d'autres marques

James Baroud

James Baroud Odyssey Manuel utilisateur

Motorola

Motorola i50sx Manuel utilisateur

Yakima

Yakima 9MM STANDARD BIKE MOUNT Manuel utilisateur

Feniex

Feniex T3 Manuel utilisateur

Renault

Renault 77 11 423 180 Manuel utilisateur

Kia

Kia E8300-4D000 Manuel utilisateur

Brink

Brink 756843 Manuel utilisateur

Whispbar

Whispbar K085W Manuel utilisateur

v.link

v.link CI-VL2-PC-HSD Manuel utilisateur

Viking

Viking Stack-Rack Guide de configuration rapide

Aries

Aries 203015 Manuel utilisateur

Choetech

Choetech AT0005 Manuel utilisateur

ZZ2

ZZ2 ZZAIR-PRO Manuel utilisateur

Holman

Holman 4A80L Manuel utilisateur

Thule

Thule 2075 Manuel utilisateur

Motorola

Motorola T325 Manuel utilisateur

TAUBENREUTHER

TAUBENREUTHER 16-3950 Guide d'installation

DV8

DV8 FBJL-02 Manuel utilisateur