B+K precision 1900B Manuel utilisateur

Model 1900B, 1901B, 1902B

Switching DC Power Supply

INSTRUCTION MANUAL

Test Equipment Depot - 800.517.8431 - 99 Washington Street Melrose, MA 02176

TestEquipmentDepot.com

1 Safety Summary

The following safety precautions apply to both operating and maintenance personnel and

must be observed during all phases of operation, service, and repair of this instrument. Before

applying power, follow the installation instructions and become familiar with the operating

instructions for this instrument.

GROUND THE INSTRUMENT

To minimize shock hazard, the instrument chassis and cabinet must be connected to

an electrical ground. This instrument is grounded through the ground conductor of

the supplied, three-conductor ac power cable. The power cable must be plugged

into an approved three-conductor electrical outlet. Do not alter the ground

connection. Without the protective ground connection, all accessible conductive

parts (including control knobs) can render an electric shock. The power jack and

mating plug of the power cable meet IEC safety standards.

DO NOT OPERATE IN AN EXPLOSIVE ATMOSPHERE

Do not operate the instrument in the presence of flammable gases or fumes.

Operation of any electrical instrument in such an environment constitutes a definite

safety hazard.

KEEP AWAY FROM LIVE CIRCUITS

Instrument covers must not be removed by operating personnel. Component

replacement and internal adjustments must be made by qualified maintenance

personnel. Disconnect the power cord before removing the instrument covers and

replacing components. Under certain conditions, even with the power cable

removed, dangerous voltages may exist. To avoid injuries, always disconnect power

and discharge circuits before touching them.

DO NOT SERVICE OR ADJUST ALONE

Do not attempt any internal service or adjustment unless another person, capable of

rendering first aid and resuscitation, is present.

DO NOT SUBSTITUTE PARTS OR MODIFY THE INSTRUMENT

Do not install substitute parts or perform any unauthorized modifications to this

instrument. Return the instrument to B&K Precision for service and repair to ensure

that safety features are maintained.

WARNINGS AND CAUTIONS

WARNING and CAUTION statements, such as the following examples, denote a

hazard and appear throughout this manual. Follow all instructions contained in

these statements.

A WARNING statement calls attention to an operating procedure, practice, or

condition, which, if not followed correctly, could result in injury or death to

personnel.

A CAUTION statement calls attention to an operating procedure, practice, or

condition, which, if not followed correctly, could result in damage to or destruction

of parts or the entire product.

WARNING:

Do not alter the ground connection. Without the protective ground

connection, all accessible conductive parts (including control knobs)

can render an electric shock. The power jack and mating plug of the

power cable meet IEC safety standards.

WARNING:

To avoid electrical shock hazard, disconnect power cord before

removing covers. Refer servicing to qualified personnel.

CAUTION:

Before connecting the line cord to the AC mains, check the rear panel

AC line voltage indicator. Applying a line voltage other than the

indicated voltage can destroy the AC line fuses. For continued fire

protection, replace fuses only with those of the specified voltage and

current ratings.

CAUTION:

This product uses components which can be damaged by electro-

static discharge (ESD). To avoid damage, be sure to follow proper

procedures for handling, storing and transporting parts and

subassemblies which contain ESD-sensitive components.

SAFETY SYMBOLS

This symbol on an instrument indicates that the user should refer to the

operating instructions located in the manual.

Certification

We certify that this product met its published specifications at time of shipment from the

factory.

Compliance Statements

Disposal of Old Electrical & Electronic Equipment (Applicable in the European Union and

other European countries with separate collection systems)

This product is subject to Directive 2002/96/EC of the European

Parliament and the Council of the European Union on waste

electrical and electronic equipment (WEEE), and in jurisdictions

adopting that Directive, is marked as being put on the market

after August 13, 2005, and should not be disposed of as

unsorted municipal waste. Please utilize your local WEEE

collection facilities in the disposition of this product and

otherwise observe all applicable requirements.

Contents

1 Safety Summary........................................................................................ 1

2 Introduction .............................................................................................. 6

3 Controls and Indicators............................................................................. 7

3.1 Front Panel........................................................................................ 7

3.2 Rear Panel ......................................................................................... 8

4 Operating Instructions .............................................................................. 9

4.1 Using the Power Supply .................................................................. 10

4.1.1 Connection .............................................................................. 10

4.1.2 Self Test Sequence .................................................................. 10

4.1.3 Control Knobs.......................................................................... 12

4.1.4 Manually Zeroing Current Meter Offset ................................. 13

4.1.5 Using Both Main and Auxiliary Outputs.................................. 14

4.2 Control Modes ................................................................................ 14

4.2.1 Normal Mode .......................................................................... 15

4.2.2 Preset Mode............................................................................ 15

4.2.3 Analog Remote Control Mode ................................................ 16

4.2.4 Set Mode................................................................................. 16

4.3 Remote Sense ................................................................................. 18

4.3.1 Connection .............................................................................. 18

4.3.2 Disconnection.......................................................................... 19

5 Remote Control....................................................................................... 19

5.1 Analog Remote Control................................................................... 20

5.1.1 Remote Control Connector Setup........................................... 20

5.1.2 Using Two External Variable DC Voltage Sources................... 21

5.1.3 Using Two 5 kΩ Variable Resistors.......................................... 23

5.1.4 Enable and Disable the Output ............................................... 24

5.2 PC Interface Control........................................................................ 25

6 Faults and Troubleshooting .................................................................... 26

6.1 OVP: Overvoltage Protection ......................................................... 26

6.2 OTP: Overtemperature Protection................................................. 26

6.3 OLP: Overload Protection............................................................... 27

6.4 Upper Voltage Limit (UVL) and Upper Current Limit (UCL) ............ 28

6.5 Fuse Replacement........................................................................... 29

7 Specifications .......................................................................................... 30

8 Certification ............................................................................................ 32

9 Service Information ................................................................................ 33

10 Limited Two-Year Warranty.................................................................... 34

Test Equipment Depot - 800.517.8431 - 99 Washington Street Melrose, MA 02176

TestEquipmentDepot.com

2 Introduction

B&K Precision models 1900B, 1901B, and 1902B are laboratory grade switching mode

DC power supplies with high current output in a small form factor and lightweight

package. The 1900B Series provide different configurations of high output voltage or

high output current and make setting voltage and current levels fast and precise

through its dual action, course/fine rotary encoder control. In addition to its constant

voltage (CV) and constant current (CC) modes, the high efficiency DC power supply

offers a unique solution with its preset and analog remote control modes. Save up to

three different presets of voltage and current values for quick recall. The analog

remote control function allows the output power, voltage, and current to be adjusted

without touching the front panel of the power supply. A remote sense terminal

(model 1900B only) is also available for use to compensate for voltage drop across

load leads. These features make the 1900B Series suitable for a wide range of

applications including production testing, telecommunications, R&D, service, and

university labs.

Features

Automatic CV/CC crossover operation

Up to 60 A output current

Lightweight and compact

Rotary encoder control for precise voltage and current setting

3 user-defined voltage and current presets

Analog remote control function

Remote sense terminal (model 1900B only)

USB interface

Front panel auxiliary output

Overvoltage, overtemperature, and overload protection

3 Controls and Indicators

3.1 Front Panel

Figure 1 - Front Panel

(1) LED panel meter display with CV/CC indicator

(2) Rear Control Indicator (lights up when using Preset/Remote Control/Set mode)

(3) Output Voltage Control Knob (control main and auxiliary output voltage)

(4) Output Current Control Knob (control main and auxiliary output current limit)

(5) Power ON/OFF Switch

(6) Auxiliary Output Terminal (max 5 A)

Note: Please see Section 4.1.5 for more details on using both main and

auxiliary output terminals together.

3.2 Rear Panel

Figure 2 - Rear Panel

(7) Main Output Terminal (max 60 A for 1900B / 30 A for 1901B / 15 A for 1902B)

Note: Please see Section 4.1.5 for more details on using both main and

auxiliary output terminals together.

(8) Remote Sense Terminal (model 1900B only)

(9) Mode Selection Switch (Normal, Preset, Remote Control, Set Modes)

(10) Recall Preset Selection Switch

(11) Analog Remote Control Terminal

(12) Cooling Fan Air Intake Grille

(13) AC Input Plug and Fuse Compartment

(14) USB Port (for PC remote control)

4 Operating Instructions

Safety Precautions

●Never short the remote sense terminal.

●This power supply is for indoor use only.

●Do not expose the power supply to sun, high humidity, or dusty

environments.

●Never remove the metal cover of the power supply while AC power is

connected.

●Never touch the unit when your hands are wet.

●Never block the ventilation slots and cooling fan air intake window.

●Never attempt to repair the power supply. Incorrect re-assembly may

result in a risk of electric shock or fire.

●Never use the power supply for a load requiring higher current than the

designed value. Otherwise it may damage the power supply.

●Place the power supply on a flat surface with sufficient clearance and dry,

dust-free surroundings for ventilation.

This series has three models with different output voltage and current ranges. Make

sure you have purchased the correct one.

Model Number

Output Voltage Range

Total Rated Current

1900B

1 –16 V

0 –60 A

1901B

1 –32 V

0 –30 A

1902B

1 –60 V

0 –15 A

Table 1 - Model Table

Test Equipment Depot - 800.517.8431 - 99 Washington Street Melrose, MA 02176

TestEquipmentDepot.com

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels B+K precision Alimentation

B+K precision

B+K precision 9120A Manuel utilisateur

B+K precision

B+K precision 9110 Manuel utilisateur

B+K precision

B+K precision MR Series Manuel utilisateur

B+K precision

B+K precision XLN3640 Manuel utilisateur

B+K precision

B+K precision 1670A Manuel utilisateur

B+K precision

B+K precision 1696B Series Manuel utilisateur

B+K precision

B+K precision 1785B Manuel utilisateur

B+K precision

B+K precision 17434 Manuel utilisateur

B+K precision

B+K precision MDL4U Series Manuel utilisateur

B+K precision

B+K precision 1785B Manuel utilisateur

B+K precision

B+K precision 1794 Manuel utilisateur

B+K precision

B+K precision 1601 Manuel utilisateur

B+K precision

B+K precision 1653A Manuel utilisateur

B+K precision

B+K precision 1760A Manuel utilisateur

B+K precision

B+K precision 1795 Manuel utilisateur

B+K precision

B+K precision 1688B Manuel utilisateur

B+K precision

B+K precision BK 1692 Manuel utilisateur

B+K precision

B+K precision 9120 Manuel utilisateur

B+K precision

B+K precision 1744A Manuel utilisateur

B+K precision

B+K precision 1747 Manuel utilisateur

B+K precision

B+K precision 1790 Manuel utilisateur

B+K precision

B+K precision 1670 Manuel utilisateur

B+K precision

B+K precision 1739 Manuel utilisateur

B+K precision

B+K precision 9115/B Manuel utilisateur

Manuels Alimentation populaires d'autres marques

Monacor

Monacor PS-12CCD Manuel utilisateur

VOLTIMA

VOLTIMA MagicBox 15 Manuel utilisateur

Agilent Technologies

Agilent Technologies 6032A Manuel utilisateur

Miller

Miller Auto Deltaweld 452 Manuel utilisateur

BCP

BCP PUOUBK Feuille d'instructions

HC 2210 Manuel utilisateur

Puls

Puls CT5.241 Manuel utilisateur

OCZ

OCZ ZX1250W Manuel utilisateur

iseg

iseg ECH 238 Manuel utilisateur

Power

Power XXL A Series Manuel utilisateur

Agilent Technologies

Agilent Technologies 6631B Manuel utilisateur

Renogy

Renogy PHOENIX 300 Manuel utilisateur

HP 6200B Manuel de service

Epson

Epson Stylus Scan 2500 Manuel d'utilisation

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Manuel utilisateur

Puls

Puls MiniLine ML50.100 Manuel utilisateur

Puls

Puls AS-Interface SLA4.100 Manuel utilisateur

Kenwood

Kenwood PS-60 Manuel utilisateur