B+B SmartWorx FOSTCDR Manuel utilisateur
Product Overview
UL Installation Guide
Terminal Block
Baud Rates
Wire the Converter
1
3
2
4
Fiber
Connectors
Terminal
Blocks LEDs
DIP Switch
Underwriters Laboratories Conditions of Acceptability –
When installed in the end-use equipment, consideration
should be given to the following:
1. The wiring terminals are suitable for factory wiring only.
2. This device is to be mounted in a suitable enclosure in
the end-product.
3. This device is suitable for operation at a maximum
surrounding air temperature as described in the
documentation.
4. These devices are intended for use in a pollution
degree 2 environment.
-Input Voltage: 10 – 30 VDC
- Input Power 4.2 Watts
- Wire Range: 12 – 24 AWG
- Tightening Torque: 4 kgf-cm
-Temperatureratingofledinstalledconductorsis
105 C minimum, sized for 60 C ampacity.
- Use copper wire only
- Maximum surrounding ambient air temperature
80 C
RS-232
RS-485 2 Wire
RS-422/RS-485 4 Wire
Fiber Optic
Terminal Signal
ARS-232 RD (OUTPUT)
BGND
CGND
DRS-232 TD (INPUT)
ENOT CONNECTED
F+10 TO 30 VDC
GRS-422/485 TDA ( - ) / DATA A ( - )
HRS-422/485 TDB (+) / DATA B (+)
J+10 TO 30 VDC
KRS-422/485 RDA ( - ) / DATA A ( - )
LRS-422/485 RDB (+) / DATA B (+)
Baud 1 2 3 4 5
4800 OFF OFF OFF OFF ON
9600 OFF OFF OFF ON OFF
19.2K OFF OFF ON OFF OFF
38.4K OFF ON OFF OFF OFF
57.6K ON OFF OFF OFF OFF
76.8K ON OFF ON ON OFF
115.2K ON ON ON OFF OFF
Recommended Accessories
DFMM-STST-1M
Fiber Optic Cable
MDR-20-24
Industrial Power Supply
Document number – 710 -10812-00_FOSTCDR-xxx _4716qsg
1-888-948-2248 | Europe: +353 91 792444
advantech-bb.com
707 Dayton Road | PO Box 1040 | Ottawa, IL 61350
Phone: 815-433-5100 | Fax: 815-433-5109
www.advantech-bb.com | E-mail: support@advantech-bb.com
Before you begin, be
sure you have the following:
FOSTCDR & FOSTCDR-INV
Industrial Serial to Multi Mode Fiber Optic
Converter
Fast and easy on the web:
www.advantech-bb.com
+ FOSTCDR-xxx Fiber Converter
+ Required but not included:
- 10-30 VDC Power Supply
- Serial Cable
- Multi-mode Fiber Optic Cable
with ST Connectors (62.5/125
micro-meter)
QUICK START
GUIDE
RS-422/RS-485 Mode Selection
DIP Switch (SW1)
5
6
Mode Position 7 Position 8
RS-485 2 Wire ON ON
RS-485 4-Wire ON OFF
RS-422 OFF OFF
Pos. ON OFF
1 RS-422/485 Baud Rate Selection
2 RS-422/485 Baud Rate Selection
3 RS-422/485 Baud Rate Selection
4 RS-422/485 Baud Rate Selection
5 RS-422/485 Baud Rate Selection
6 FO Multi-drop Ring FO Point-to-Point
7 RS-422/485 Mode Selection
8 RS-422/485 Mode Selection
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels B+B SmartWorx Convertisseur de média
B+B SmartWorx
B+B SmartWorx 422CEC Instructions d'utilisation et d'entretien
B+B SmartWorx
B+B SmartWorx FOSTCDRi-PH-MT Instructions d'utilisation et d'entretien
B+B SmartWorx
B+B SmartWorx 422TTL Manuel utilisateur
B+B SmartWorx
B+B SmartWorx 422PP9R Instructions d'utilisation et d'entretien
B+B SmartWorx
B+B SmartWorx USOPTL4-2P Manuel utilisateur
B+B SmartWorx
B+B SmartWorx 4WSD9R Manuel utilisateur
B+B SmartWorx
B+B SmartWorx SCP211-DFTB3 Manuel utilisateur
B+B SmartWorx
B+B SmartWorx 232OTTL Manuel utilisateur
B+B SmartWorx
B+B SmartWorx IE-MultiWay Manuel utilisateur
B+B SmartWorx
B+B SmartWorx IE-MiniFiberLinX-II Series Manuel utilisateur
