Boundaryline SLEEKWALL SOLID Manuel utilisateur

Install Guide

SLEEKWALL

Solid

A step-by-step guide to installing your new fence

Version 1.0

Boundaryline SleekWall Solid Install Guide

0800 003 006 | boundaryline.co.nz

Make sure you choose the right tools before you start your fence

It is recommended that the reader pays particular aention to those items identiﬁed as IMPORTANT in this manual

to ensure satisfactory long-term performance.

Tools Safety Gear minimum required

Thank you for choosing Boundaryline SleekWall

Solid Fencing. This product will provide you with

many years of trouble free protection if installed

in accordance with the directions outlined in this

document.

The recommendations detailed in this guide

are formulated along the lines of good building

practice. They are not intended to be an exhaustive

statement of all the relevant data.

If you have any questions, please contact our

Technical Team on 0800 003 006. We are always

happy to help in any way we can.

Introduction

FTape measure

FSquare

FShovel

FLine marking paint

FString line

FSpirit or laser-level

FHex drive bit

FHacksaw or powered metal

cuing saw

FDrill

FPost hole digger/Auger 300mm

FSafety boots

FGloves

FHelmet

FEye protection

FHearing protection

FSun protection

Before you start, read this

This guide does not apply to any fences over 1.8m in

height. If your fence is greater that 1.8m, please seek

further advice from Boundaryline.

- Describe your site details when ordering materials.

- IIdentify your soil type/ground conditions. Refer to the

table in Step 2. This will determine the concrete and

footing details required

- Make sure you are aware of underground services

before you start digging! These could be gas, electricity,

or water mains. Call your local council for more

information.

- Check your local council regulations on boundary

fencing.

- Check the delivered material for the correct number

of components and general condition before beginning

your installation.

0800 003 006 | boundaryline.co.nz 03

Boundaryline SleekWall Solid Install Guide

145x16x1780mm TGV Paling

Components List

Required for this product These items below are

not included but one

type of post and cap are

required for installation.

30x30 paling channel

Channel cover clip

Channel ends caps, le & right

Tek screws

65x65 in-ground post

65x65 flanged post

Plastic knock in cap

Aluminium post cap

30x30 paling channel x2

Tek screws

100x16x1780mm slat x1

Conversion kit components

To change the orientation of your fence

Boundaryline SleekWall Solid Install Guide

0800 003 006 | boundaryline.co.nz

Step 2 | Marking out and digging post holes

Determine your post hole centres using the table below as a guide and mark out your post hole positions on the ground with line

marking paint

Marking out your post holes

Standard ‘post centre to post centre’ guide

The table above allows you to work out what your post

centres will be. If you have 1780mm paling [allowing

for 10mm either side of the channel] and you are using

65x65mm posts, then you will have an 1865mm post

centre to post centre

This also shows the in-between measurements, should

you be ﬁing your paling between posts other than a

65x65mm proﬁle, i.e, timber posts or concrete blocks

Recommended footing depths listed in this table are for wind regions A & B, plus terrain categories 2.0, 2.5 & 3.

If you are building your fence in a cyclonic wind area, on top of a hill, adjacent to an escarpent, on a ridge or in terrain

category 1, you will need engineering advice beyond the scope of this publication

Required post-hole depth into ﬁrm

earth or clay

Wall Height Post hole depth

900mm 450mm

1200mm 550mm

1500mm 600mm

1800mm 600mm

Notes:

For higher walls, you will need engineering advice beyond the scope of this

publication

The diameter of your holes should be large enough to have a minimum of 75mm

clearance around the post

Please note that 1800mm is the standard height. Heights lower than 1800mm

can be done using these components, with wastage.

Step 1 | Lay out your fence line

a. Accurately determine & mark any legal boundaries and/or underground services (a surveyor may be required)

b. Measure out each fence line & mark the post positions

Determine post centres as follows

c. If the fence line length does not work out as multiples of the standard panel length, adjust the length of the last

section, or the last few sections, to suit & cut panels to ﬁt

d. Use a string line or laser level to make sure any straight lines are aligned

Panel length +Post size =Post centre

E.g. 1800mm + 65mm = 1865mm

String line

Post face to post facePost face to post face

Post face

Boundary line

Position the boundary line at

half the depth of the post

TGV Paling length 65x65mm post hole centres In-between post measurements

1780mm paling 1865mm 1800mm

Boundaryline SleekWall Solid Install Guide

0800 003 006 | boundaryline.co.nz

Step 3a | Installing the posts - In-ground

a. Place the post into the hole and set the height carefully using a tape measure or, preferably, a laser level

Caution: Ensure you allow enough height on the post to allow for panel height + ground clearance (suggest 50-100mm) +

additional 25mm for bracket & cap clearance

b. Fill the hole with concrete around the post, taking care to keep the post in the correct position

c. Check with a spirit level regularly to ensure the post is plumb

d. Ensure the post remains square to the fence line & does not turn as you lace concrete around it

e. Repeat steps a to d for all posts

f. Set the spacing of the posts at the length of the panel, plus approximately 5mm clearance (as per step one)

Tip: cut a spacer stick out of timber at the correct length between posts. The standard/raking/Axis panel brackets are 30mm

deep - so this allows for some adjustment if required, except where a PS1 is required

In-ground post

OAP6519 65x65x1900mm

OAP6525 65x65x2500mm

OAP1025 100x100x2500mm

Post sizes are dependent on the application & design requirements

Posts to be installed in ‘good ground’ as deﬁned by NZS3604

For in-ground posts

SHS Aluminium 65x65x2.0

Slope top of concrete to

allow water to drain away

from the post

Concrete 17.5MPA min

“Good ground”

100kPa Allowable bearing Min 500mm

100mm

Min 600mm

300mm dia

or 250x250mm square

Ground level

Step 3b | Installing the posts - Bolt down

a. Ensure the surface you are bolting the post to is ﬁrm, level & clean

b. Fix the posts in place with four ﬁxings of the correct type for the

situation

Bolt down post

OAF6513 65x65x1300mm

OAF6519 65x65x1900mm

Post sizes & ﬁxings are dependent on the application & design

requirements

Fixings - indicative

In concrete: 4x M12 HILTI HST stud anchors or similar with minimum 70mm

embedment

In timber: 4x 12mm coachscrews with minimum 120mm embedment

SHS Aluminium 65x65x2.0

Fully Welded around 4

sides of post

125.0mm

89.0mm

18.0mm 50mm

Flange 125x125x5

125.0mm

For bolt down posts

–For standard 65x65mm (and smaller) aluminium

posts, a fairly dry concrete mix can be used which

will hold the post in place without any bracing

while the concrete dries. However, the site must be

revisited before the concrete sets ﬁrm to recheck

post alignment if required

–Any heavier posts, i.e., gate posts, should be

concreted in place and braced until the concrete is

dry

–If the fence line follows any contours in the land or

the fence line is curved, regularly check the height

of the posts as you work down the line to ensure a

good visual line along the top of the fence

Boundaryline SleekWall Solid Install Guide

0800 003 006 | boundaryline.co.nz

Paling channel installation

Step 4 | Fiing paling channels

If your channels are not the desired length then these will need to be cut, ideally, with a dropsaw to obtain a clean cut without heating

the aluminium to a point that it burns the powdercoating.

With the use of a tape measure, string line/chalk line, or if you have access to a laser level, you can mark the heights of the top of your

paling channel on your posts.

Note: if your site has sloping ground it may be required to step your fence from bay to bay. Once a height has been established for all

of your channels, with the tek screws supplied, screw your channel directly to your post whilst keeping the top of your channel at the

marks you have made on your post

Your screws should be approximately 300-400mm apart down the length of your channel.

Paling cavity

Post

Paling screw

port

Cover clip

Note:

Make sure the post is elevated 10mm higher

than the channel to allow for a post cap

the paling channel is asymmetrical.

To ensure your fence aesthetically looks correct,

make sure the ‘screw port side’ is all facing the

same direction (generally on the inside of your

property looks best).

Aach paling channel

to post by screwing

through the paling cavity

Boundaryline SleekWall Solid Install Guide

0800 003 006 | boundaryline.co.nz

Step 6 | Insert channel cover clip and channel caps

Once all your palings have been assembled you can

now install the cover clip to the channel to hide all visible

ﬁxings.

Make sure the cover clip is the same length as your paling

channel, then you are ready to insert.

The easiest way to do this is to use either a rubber mallet

or the rubber handle of a hammer. Do not use the metal

part of your hammer as this may damage the powder

coating.

Insert one edge of the cover clip into the channel, then

ﬁrmly tap in the other edge along the length of the

channel until it is all secured in place.

One all the palings have been installed, we have an

optional cap to cover the proﬁle of the paling channel.

These consist of a le and right hand cap.

Caps are just inserted onto the top of the channel.

Cover clip installation

Cover clip hides screw

heads once ﬁed

Le & right

channel caps

Channel

cover clip

Paling installation

Step 5 | Fiing palings

See vertical conversion guide on pg 9 to change the orientation of your fence.

The palings have a groove one side and a tongue on the other, so they

interlock when stacked on each other.

Starting at the boom, slide and screw the ﬁrst paling into the channel with

the tongue up, then slide the next paling in with its groove locking over the

tongue and repeat until they are all stacked. Then place the tongue cover

over the last paling and screw into place.

If you do a lower height than 1800mm, you will need to divide the height of

your wall into the number of palings you have to obtain the closest number

of palings.

Note: It is important to maintain both parallel and level within each bay. This

will ensure a straight looking fence.

This can be achieved by using a tape measure to check for the ‘parallel’

with either the top of the channel or your starting point.

One screw per paling is

all that is required

Post to be 10mm higher

for the post cap

0800 003 006 | boundaryline.co.nz 08

Boundaryline Vertical Conversion Guide

Vertical conversion guide

How to convert the orientation of your SleekWall Solid fence.

Fiing boom paling

Depending on the total width of the bay, the

maximum post width face to face is 1800mm.

Lay the additional slat horizontal and screw ﬁx on either

end. Trim channel to the total length of the exposed

paling between posts. Screw ﬁx this to the top of the

slat, this will become the base of the vertical palings.

Fiing vertical palings

Starting from one side, ﬁx one paling against

one side and work across, making sure the

tongue and grooves are fully secured.

Tip: use a strap or similar close to the top of the post

to secure the inserted palings while installing

Fiing top cap

Aer ﬁing all the palings, place the top cap

across and screw ﬁt to secure the fence

Slat

Post

Paling channel

Boundaryline SleekWall Solid Install Guide

0800 003 006 | boundaryline.co.nz

Contact Boundaryline Fencing

0800 003 006

boundaryline.co.nz

This document is only intended to be a general guide, as every property & situation is dierent. Any installation work, including the use

of power equipment is completely the responsibility of the person(s) installing. All persons using power equipment must be trained &

certiﬁed to use the equipment & must wear all applicable personal protection gear. Terranota Ltd cannot accept any responsibility for

any faulty installation or damage or injury arising from installation work.

What is the best method to cut aluminium?

For the best results, use a drop saw with an

aluminium cuing blade. This will create a clean,

square cut. A grinder is acceptable, provided you

use a thin metal cuing blade to reduce the risk of

burning the powdercoat.

Can this be installed in coastal areas?

Yes, we have a 5 year warranty on our products.

If you are in a coastal zone then an increase of

cleaning and maintenance will be required.

We do not recommend the product to be in direct

contact with salt water.

What do I do if I have hard water?

Regular cleaning of your fence will be required to

help prevent water spots from appearing. Hard water

is corrosive to the powder coating, therefore neglect

will cause deterioration to your fence.

Can this be used for a balustrade?

No, currently, this has not been tested for balustrade

purposes.

How do I set up my posts around angles?

You will need two posts for this. The channel system

is required to be square to the posts and palings.

This can only be done with two posts side by side.

Frequently asked questions

Can this product be used as a balustrade over 1m

high?

No, as we do not have PS1 F4 Building

Documentation available for this product.

Can this be used as pool fencing?

Yes, however, the wall needs to be a minimum of

1200mm high. Please note however, we do not have

PS1 F9 Building Documentation available for this

product yet, which the local council may ask for.

hps://www.building.govt.nz/

buildingcodecompliance/f9-safety-of-users/

poolsafety/

Autres manuels pour SLEEKWALL SOLID

Table des matières

Autres manuels Boundaryline Clôtures et portails

Boundaryline

Boundaryline SLEEKWALL SOLID Manuel utilisateur

Boundaryline

Boundaryline ELITEWALL DuraPanel Mode d’emploi

Boundaryline

Boundaryline ColourPanel Manuel utilisateur

Boundaryline

Boundaryline ELITEWALL ALUMINIUM SLAT Manuel utilisateur

Boundaryline

Boundaryline SMARTWALL Manuel utilisateur

Manuels Clôtures et portails populaires d'autres marques

Casanoov

Casanoov KIT-000045 Manuel utilisateur

Heras

Heras SHB21 Manuel utilisateur

Casanoov

Casanoov VOGEL 350C140 Manuel utilisateur

DITEC

DITEC Silver 1B/40B Manuel

Casanoov

Casanoov EIGER 350C140 Manuel utilisateur

Olli

Olli Lister WZG 180B Manuel utilisateur

WamBam

WamBam BL19042 Manuel utilisateur

Wisniowski

Wisniowski MakroPro 100 Manuel utilisateur

Zippity

Zippity WASHINGTON Manuel utilisateur

Roger Technology

Roger Technology LT338 Manuel utilisateur

CAI

CAI SG-60-PCY Manuel utilisateur

Hahn

Hahn hanit Mode d'emploi

Oxgard

Oxgard K-14 Manuel utilisateur

patura

patura P4500 Manuel utilisateur

Betafence

Betafence HoriZen Prime Manuel utilisateur

VIEWRAIL

VIEWRAIL Vedera Manuel utilisateur

Alvarado

Alvarado CSG Manuel utilisateur

RTL

RTL INSTABOOM LITE Manuel utilisateur