Boss Audio Systems GT2500D Manuel utilisateur

1000M

Service Manual

MODEL: GT2500D

SPECIFICATIONS

Maximum power output (2 Ohms): 1500W x 1ch

RMS power Output: 900W x 1ch

Bridged Power Output: 2500W x 1ch

Frequency response: 50 - 150Hz

S/N Ratio: 100dB

Low Pass Crossover (Variable) 50Hz-150Hz

Power Source Voltage: 14.4V

Ground: Negative

External dimensions: 236(W)x55(H)x318(D)mm

2. Place the parts and wiring back in their original positions after replacement or

re-wiring. For proper circuit construction, use of insulation tubes, bonding, gaps to

PCB, etc, is involved. The wiring connection and routing to the PWB are specially

planned using clamps to keep away from heated and high voltage parts. Ensure that

they are placed back in their original positions after repair or inspection. If extended

damage is caused due to negligence during repair, the legal responsibility shall be

with the repairing company.

3. Check for safety after repair. Check that the screws, parts and wires are put back

securely in their original position after repair. Ensure for safety reasons there is no

possibility of secondary ploblems around the repaired spots. If extended damage is

caused due to negligence of repair, the legal responsibility shall be with the repairing

company.

4. Caution in removal and making wiring connection to the parts for the automobile.

Disconnect the battery terminal after turning the ignition key off. If wrong wiring

connections are made with the battery connected, a short circuit and/or fire may occur.

If extensive damage is caused due to negligence of repair, the legal responsibility

shall be with the repairing company.

5. Cautions regarding chips.

Do not reuse removed chips even when no abnormality is observed in their

appearance. Always replace them with new ones. (The chip parts include resistors,

capacitors, diodes, transistors, etc). The negative pole of tantalum capacitors is

highly susceptible to heat, so use special care when replacing them and check the

operation afterwards.

6. Cautions in handling flexible PCB

Before working with a soldering iron, make sure that the iron tip temperature is

around 270... Take care not to apply the iron tip repeatedly(more than three times)

to the same patterns. Also take care not to apply the tip with force.

7. Turn the unit OFF during disassembly and parts replacement. Recheck all work

before you apply power to the unit.

To engineers in charge of repair or inspection of

our products.

Before repair or inspection, make sure to follow the instructions so that customers

and Engineers in charge of repair or inspection can avoid suffering any risk or injury.

1. Use specified parts.

The system uses parts with special safety features against fire and voltage. Use only

parts with equivalent characteristics when replacing them. The use of unspecified

parts shall be regarded as remodeling for which we shall not be liable. The onus of

product liability (PL) shall not be our responsibility in cases where an accident or

failure is as a result of unspecified parts being used.

- 2 -

EXPLODED VIEW

- 3 -

1000M

- 4 -

PRINTED CIRCUIT BOARD - 1

- 5 -

CIRCUIT DIAGRAM 1

- 6 -

CIRCUIT DIAGRAM 2

- 7 -

PARTS LIST - 1

- 8 -

PARTS LIST - 2

- 9 -

PARTS LIST - 3

- 10 -

PARTS LIST - 4

Table des matières

Autres manuels Boss Audio Systems Amplificateur de voiture

Boss Audio Systems

Boss Audio Systems Diablo D450.4 Manuel utilisateur

Boss Audio Systems

Boss Audio Systems Klash K480 Manuel utilisateur

Boss Audio Systems

Boss Audio Systems NXD5500 Manuel utilisateur

Boss Audio Systems

Boss Audio Systems CX1000 Manuel utilisateur

Boss Audio Systems

Boss Audio Systems CLR-40 Manuel utilisateur

Boss Audio Systems

Boss Audio Systems powerDrive PD-1000 Manuel utilisateur

Boss Audio Systems

Boss Audio Systems Chaos Exxtreme CX2500D Manuel utilisateur

Boss Audio Systems

Boss Audio Systems CHAOS CH3000D Manuel utilisateur

Boss Audio Systems

Boss Audio Systems CHAOS REV-1000 Manuel utilisateur

Boss Audio Systems

Boss Audio Systems CHAOS CH1000 Manuel utilisateur

Boss Audio Systems

Boss Audio Systems Outcast OL2400 Manuel utilisateur

Boss Audio Systems

Boss Audio Systems Diablo D800.2 Manuel utilisateur

Boss Audio Systems

Boss Audio Systems US180 Manuel utilisateur

Boss Audio Systems

Boss Audio Systems CHAOS CH1000 Manuel utilisateur

Boss Audio Systems

Boss Audio Systems Diablo D1000.2 Manuel utilisateur

Boss Audio Systems

Boss Audio Systems Riot GT1000M Manuel utilisateur

Boss Audio Systems

Boss Audio Systems Rage REV-485 Manuel utilisateur

Boss Audio Systems

Boss Audio Systems RiotGT GT2000D Manuel utilisateur

Boss Audio Systems

Boss Audio Systems Blade Extreme BLX3500M Manuel utilisateur

Boss Audio Systems

Boss Audio Systems Ripper RIP-495 Manuel utilisateur

Boss Audio Systems

Boss Audio Systems CE102 Guide de l'utilisateur

Boss Audio Systems

Boss Audio Systems CER1200M Manuel utilisateur

Boss Audio Systems

Boss Audio Systems Riot GT880 Manuel utilisateur

Boss Audio Systems

Boss Audio Systems Blade BL3KD Manuel utilisateur

Manuels Amplificateur de voiture populaires d'autres marques

Cyfre

Cyfre CHACDMA-819 Manuel utilisateur

MTX

MTX Thunder Marine TM904 Manuel utilisateur

MTX

MTX Thunder TA Super TA92001 Mode d’emploi

Lanier

Lanier 480-0239 Instructions d'utilisation et d'entretien

Kenwood

Kenwood KAC-642 Manuel utilisateur

Pioneer

Pioneer GM-D8500M Manuel utilisateur

Jensen

Jensen XA4150 Manuel utilisateur

Sony

Sony XM-405EQX Marketing Specifications Manuel utilisateur

Audiopipe

Audiopipe AQX-660.2 Manuel utilisateur

Clarion

Clarion APA2001 APA2001 APA2001 Guide de démarrage rapide

Sony

Sony XM-7547 Manuel utilisateur

Alpine

Alpine PDX11000 - Amplifier Manuel utilisateur

Steg

Steg Qx Mos 105.4x Manuel utilisateur

JL Audio

JL Audio HD900/5 Manuel utilisateur

Memphis

Memphis 16-MC5.700 Manuel utilisateur

Audiopipe

Audiopipe APSM-1150 Manuel utilisateur

Kenwood

Kenwood KAC-PS811D Manuel utilisateur

Fusion

Fusion CA-DA41400 Manuel utilisateur