Bosch B450 Mode d'emploi
Conettix Plug-in Communicator
Interfaces
B450
en Installation and Operation Guide
Conettix Plug-in Communicator Interfaces Table of contents | en 3
Bosch Security Systems, Inc. Installation and Operation Guide 2017.10 | 09 | F.01U.300.740
Table of contents
1Safety 4
2Introduction 5
2.1 About documentation 5
2.2 Bosch Security Systems, Inc. product manufacturing dates 5
2.3 Installation workflow 6
3System overview 7
3.1 Module overview 7
3.2 Cellular interface compatibility 8
3.3 Bus address settings 9
4Installation 12
4.1 Inserting a plug-in cellular module (required) 12
4.2 Mounting the module 13
4.3 Installing the tamper switch (optional) 14
4.4 Installing the cellular antenna 14
4.5 Connecting the module to the control panel 15
4.5.1 Connecting to SDI2 and SDI control panels 15
4.5.2 Connecting to option bus control panels 16
5Configuration 17
5.1 Configuration parameters 17
5.2 Plug and Play (PnP) configuration 21
5.2.1 RPS configuration 21
5.3 USB configuration 22
5.3.1 Get started 22
5.3.2 B450 home page 26
5.3.3 Main Menu 28
5.3.4 Status menu 29
5.3.5 Basic and Advanced Configuration menus 34
5.4 SMS configuration 34
5.4.1 Creating the SMS 34
5.4.2 Sending the inbound SMS 36
5.4.3 Exiting from CONFIG mode 37
5.4.4 Configuration 37
6Maintenance and troubleshooting 38
6.1 Firmware updates 38
6.2 USB menu access disabled 40
6.3 LED status indicators 41
6.4 Firmware version LEDs 44
6.5 SIM card 44
6.6 Diagnostic log 44
6.7 Network polling 45
6.8 Control panel programming using cellular 45
6.9 RPS Diagnostics 45
7Technical specification 46
4en | Safety Conettix Plug-in Communicator Interfaces
2017.10 | 09 | F.01U.300.740 Installation and Operation Guide Bosch Security Systems, Inc.
1 Safety
ESD Precaution
Please note that while the module comes in a plastic case, and is protected from ESD, the
plug-in cellular communicator (B44x) does not. All plug-in cellular communicator components
may potentially be exposed to finger touches - therefore extra attention must be paid to ESD
(electrostatic discharge) precaution.
Make sure there is no static interference when using the board. Appropriate ESD protections
must be taken and wearing electrostatic equipment is recommended, such as anti-static wrist
strap.
ESD damage ranges from subtle performance degradation to complete device failure.
Precision integrated circuits may be more susceptible to damage because very small
parametric changes could cause the device not to meet its published specifications.
!
Warning!
Failure to follow these instructions can result in a failure to initiate alarm conditions. Bosch
Security Systems, Inc. is not responsible for improperly installed, tested, or maintained
devices. Follow these instructions to avoid personal injury and damage to the equipment.
Notice!
Inform the operator and the local authority having jurisdiction (AHJ) before installing the
module in an existing system.
Disconnect all power to the control panel before installing the module.
Before you install the module, refer to the technical specifications.
Conettix Plug-in Communicator Interfaces Introduction | en 5
Bosch Security Systems, Inc. Installation and Operation Guide 2017.10 | 09 | F.01U.300.740
2 Introduction
This document contains instructions for a trained installer to install, configure, and operate
this module.
2.1 About documentation
Copyright
This document is the intellectual property of Bosch Security Systems, Inc. and is protected by
copyright. All rights reserved.
Trademarks
All hardware and software product names used in this document are likely to be registered
trademarks and must be treated accordingly.
2.2 Bosch Security Systems, Inc. product manufacturing dates
Use the serial number located on the product label and refer to the Bosch Security Systems,
Inc. website at http://www.boschsecurity.com/datecodes/.
6en | Introduction Conettix Plug-in Communicator Interfaces
2017.10 | 09 | F.01U.300.740 Installation and Operation Guide Bosch Security Systems, Inc.
2.3 Installation workflow
To install and configure the module, use the workflow below.
!
Caution!
Remove all power (AC and battery) before making any connections. Failure to do so might
result in personal injury and/or equipment damage.
Plan the installation of the B450 Conettix Plug-in Communicator Interface.
Unpack the device contents.
Power down the system.
Set the bus address value to automatically configure the module to work with a
compatible control panel. Refer to Bus address settings, page 9.
Insert a plug-in communicator into the module. Refer to Inserting a plug-in cellular module
(required), page 12.
Mount the module into the enclosure. Refer to Mounting the module, page 13.
Wire the module to a compatible control panel. Refer to Connecting the module to the
control panel, page 15.
Power up the system.
Install a communication program (if required). Refer to Get started, page 22.
Configure the communication module (SDI and option bus control panels).
Verify LED activity. Refer to LED status indicators, page 41.
Review the signal strength of the cellular communicator. Refer to the installation
instructions for cellular communicator.
Conettix Plug-in Communicator Interfaces System overview | en 7
Bosch Security Systems, Inc. Installation and Operation Guide 2017.10 | 09 | F.01U.300.740
3 System overview
1
2
7
5
6
3
4
8
9
Callout ￚ Description Callout ￚ Description
1 ￚ Compatible control panel 6 ￚ Cellular carrier network
2 ￚ Panel data bus (SDI2, SDI, or option) 7 ￚ Internet/LAN/WAN
3 ￚ B450 8 ￚ Remote Programming workstation
4 ￚ USB connection for module configuration 9 ￚ Compatible IP receiver (Bosch D6100IPv6
shown)
5 ￚ B44x plug-in communicator (available
separately)
3.1 Module overview
The module is a four-wire powered SDI, SDI2, or option bus device that provides two-way
communication over commercial cellular networks using a plug-in communicator.
To configure the module, use one of the following tools:
–Plug and Play (PnP) configuration, page 21 (SDI2 and some option bus control panels)
–USB configuration, page 22 (all control panels)
–SMS configuration, page 34 (all control panels)
8en | System overview Conettix Plug-in Communicator Interfaces
2017.10 | 09 | F.01U.300.740 Installation and Operation Guide Bosch Security Systems, Inc.
1
862
9
10
3
754
TX RX
Callout ￚ Description
1 ￚ Tamper switch connector
2 ￚ Bus address switch
3 ￚ MODE 2-pin jumper connector (for future use)
4 ￚ Bus address label
5 ￚ USB connector (Type A)
6 ￚ Heartbeat LED
7 ￚ RX LED (indicates packets received from the wireless network)
8 ￚ TX LED (indicates packets transmitted over the wireless network)
9 ￚ Terminal strip (to control panel)
10 ￚ Interconnect wiring connectors (to control panel or other compatible modules)
3.2 Cellular interface compatibility
The module supports multiple bus types. Refer to the table to determine the supported
applications and features by bus type.
Installed Bus
Function Option/SDI SDI2 Details
IP Event Reporting Y Y TCP communication
is only supported on
SDI2
Remote Program
(RPS or A-link)
Y Y Requires Bosch
Cellular service or
other cellular network
access
Conettix Plug-in Communicator Interfaces System overview | en 9
Bosch Security Systems, Inc. Installation and Operation Guide 2017.10 | 09 | F.01U.300.740
Installed Bus
Configure module
from control panel
N Y GV4/B Series require
v2.03+
Personal Notification
via SMS or Email
N Y Requires compatible
control panel and
cellular plan
Remote Security
Control App
N Y Requires Bosch
Cellular service or
other cellular network
access
The module also supports multiple cellular networks through the use of Bosch cellular
communication modules. Refer to the following table to determine the supported Bosch
cellular module and corresponding cellular network technology.
Cellular technology compatibility
Device Cellular networks
2G (CDMA) 3G (CDMA) GPRS (GSM) HSPA+ (GSM) 4G (LTE)
B440/B440-C* X X
B441/B441-C* X
B442* X
B443* X X
B444* X
*Check for availability in your region.
3.3 Bus address settings
The control panel uses the address for communications. Use the address switch to set the bus
type and the module address on the bus. Use a slotted screwdriver. Refer to the address label
on the module and the following table to choose the address switch for the control panel
type.
10 en | System overview Conettix Plug-in Communicator Interfaces
2017.10 | 09 | F.01U.300.740 Installation and Operation Guide Bosch Security Systems, Inc.
PANEL ADDRESSES
TX RX
0 1 2 4 5 6 7 8 9
Bus cfg 1 2 88 92 250
Addr SDI2 SDI Option
134 13 14
Control panels Switch
position
Control
panel bus
address
Bus type Function
USB or SMS
configuration setting
0 N/A Any Configuration
B9512G/B8512G/
B6512/B5512/B4512/
B3512, D9412GV4/
D7412GV4/D7212GV4
1 1 SDI2 Automation, Remote
Programming, Reporting
B9512G/B8512G/
D9412GV4/D7412GV4/
D7212GV4
2 2 Automation, Remote
Programming, Reporting
D9412GV4/D7412GV4/
D7212GV4, D9412GV3/
D7412GV3/D7212GV3,
D9412GV2/D7412GV2/
D7212GV2 v7.06+
4 88 SDI1Remote Programming or
Reporting
D9412GV4/D7412GV4/
D7212GV4, D9412GV3/
D7412GV3/D7212GV3
5 92 Remote Programming, Reporting
Autres manuels pour B450
1
Table des matières
Autres manuels Bosch Équipement d'enregistrement
Bosch
Bosch Worcester Greenstar HIU E Manuel utilisateur
Bosch
Bosch DVR1A1081 Manuel utilisateur
Bosch
Bosch Rexroth IMenip Manuel utilisateur
Bosch
Bosch Divar 700 Series Manuel utilisateur
Bosch
Bosch DIVAR IP all-in-one 6000 Manuel utilisateur
Bosch
Bosch LBB 1968/00 Manuel utilisateur
Bosch
Bosch Rexroth IMenip2 Manuel utilisateur
Bosch
Bosch DIVAR IP all-in-one 4000 Manuel utilisateur
Bosch
Bosch B450 Instructions d'utilisation d'origine
Bosch
Bosch CLIMATE 5000 VRF RDCI Series Mode d’emploi
Bosch
Bosch FLM-420-O8I2-S Manuel utilisateur
Bosch
Bosch DX4010V2 Manuel utilisateur
Bosch
Bosch FLM-420-NAC-S Manuel utilisateur
Bosch
Bosch Climate 5000 Series Manuel utilisateur
Bosch
Bosch HPC 410 Manuel utilisateur
Bosch
Bosch FLM-420-O2-D Manuel utilisateur
Bosch
Bosch M 60 Manuel utilisateur
Bosch
Bosch B450-M Manuel utilisateur
Bosch
Bosch MIC-ALM-WAS-24 Manuel utilisateur
Bosch
Bosch TINYON IP 2000 WI Instructions de montage
Manuels Équipement d'enregistrement populaires d'autres marques
Strymon
Strymon NIGHTSKY Manuel utilisateur
Mitsubishi Electric
Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Manuel utilisateur
Tews Technologies
Tews Technologies TPMC465 Manuel utilisateur
Honeywell
Honeywell Excel 50 Manuel utilisateur
SeaLevel
SeaLevel COMM+8.LPCI Manuel utilisateur
Arturia
Arturia AUDIOFUSE STUDIO Manuel utilisateur
