Bosch AEC-AMC2-VDS1 Manuel utilisateur
AEC-AMC2-VDS1
en Installation manual
de Installationshandbuch
pl Instrukcja instalacji
zh 安装指南
nl Installatiehandleiding
ru Руководство по установке
hu Telepítői kézikönyv
pt Manual de instalação
es Manual de instalación
AEC-AMC2-VDS1 3
Bosch Sicherheitssysteme GmbH F.01U.097.255 | V 3.1 | 2008.12
English
Deutsch
Polski
中文
Nederlands
Magyar
Português brasileiro
Español latinoamericano
AEC-AMC2-VDS1 - Installation manual en 5
Bosch Sicherheitssysteme GmbH F.01U.097.255 | V 3.1 | 2008.12
Included parts
The metal housing inlcudes the following components:
Figure 1 Parts of the housing
1 = Name plate
2 = AMC grounding post
3 = Mounting rail for PS and AMC
4 = Cable knock-out for reader and signal cables
5 = Opening for rechargeable battery securation
6 = Cover tamper switch
7 = Power cable knock-out
8 = Label
9 = Three pin connector
10 = Cover grounding post
11 = Main grounding post
12 = Power supply connector
6en AEC-AMC2-VDS1 - Installation manual
F.01U.097.255 | V 3.1 | 2008.12 Bosch Sicherheitssysteme GmbH
The accessories kit includes the following cables. Install these
cables as described in Section Connection of the Devices,
page 8.
Figure 2 Accessories kit content
Content of the accessories kit:
A= Pre-assembled cable to connect the AMC to the power
supply
B= Pre-assembled cable to connect the rechargeable batteries
to the UPS (uninterruptable power supply) which is included in
the power supply
C= Cable using 24 V mode
D= Grounding cable for the cover
E= Cable ties to secure the pre-assembled cable
F= Cable ties to fix the rechargeable batteries
G= Pre-assembled cable with temperature sensor
H= Three screw anchors S8 and wood screws M6 x 50
J= Bracket for cable fixing
Before the assembly of the housing the following preparations
should be done and conditions be considered.
AEC-AMC2-VDS1 - Installation manual en 7
Bosch Sicherheitssysteme GmbH F.01U.097.255 | V 3.1 | 2008.12
The opening for the AC supply cable (position 7) is covered by
two plastic inserts. The AC cable can either be routed through a
standard cable duct (40 mm x 25 mm) or be introduced directly
from the back of the housing. Disrupt the appropriate plastic
insert such that you can insert the power cable properly.
Mounting the Housing
Open the housing cover lock with the provided key and remove
the hood from the wall mounted frame.
Mount the metal housing at the desired position with the screw
anchors provided with the enclosure.
Use the screws (position Hof the accessories kit) at the points
to mount the housing against the wall.
Figure 3 Demensions of the housing
8en AEC-AMC2-VDS1 - Installation manual
F.01U.097.255 | V 3.1 | 2008.12 Bosch Sicherheitssysteme GmbH
Connection of the Devices
Figure 4 Connection of the devices
1. Mount the AMC on the rail (item 3 in Figure 1) and left
aside the power supply.
2. Put the rechargeable batteries on the bottom of the
housing and secure them with the cable ties F - (Figure 2).
3. Stick the bracket J Figure 2 on the back of the housing in
such a way that later on not used connectors of the cable
Bcan fixed with it.
4. Cable set A:
a. Connect the 7-pin plug A1 to the AMC’s power supply
connector (labeled: POWER).
b. Attach connectors A3 to the PS-interface DC and A2
to the interface labeled OK.
c. Connect the grounding cable A4 beneath the
grounding point 2.
5. Cable set B:
i
NOTICE!
The following steps describe connecting the rechargeable
batteries in 24 V mode. For information on 12 V mode
connections, refer to Section 12 V Mode Variations, page 11.
AEC-AMC2-VDS1 - Installation manual en 9
Bosch Sicherheitssysteme GmbH F.01U.097.255 | V 3.1 | 2008.12
a. Connect the plug connector B1 the second position
from the left on the power supply - labeled with BAT.
b. Attach connector B2b (red) to the +-pin of the first
rechargeable battery.
c. With cable Cconnect the --pin of the first
rechargeable battery to the +-pin of the second
rechargeable battery.
d. Attach connector B2a (black) to the --pin of the
second rechargeable battery.
e. Connectors B3a and B3b are not used.
6. Cable set G:
a. Attach connector G1 on the PS-interface labbeled
RTH.
b. Route the cable across the temperature sensor
bracket Jso that the temperature sensor G2 hangs
approximitely 5 cm (2 in.) above the rechargeable
batteries.
7. Pre-assembled cable set 12:
a. Connect the 2-pin plug on the interface AC of the
power supply.
8. Pre-assembled cable 6:
a. Connect the loose ends of the cover tamper switch to
the 2-pin screw connector on the top of the AMC.
Position the cable in the space between the housing
and the mounting rail.
9. Connect the main AC supply X:
a. Connect the brown (phase) wire to terminal L1.
b. Connect the blue (neutral) wire to terminal N.
c. Connect the grounding cable to the housing at
position 11.
DANGER!
Remove the fuse from the three-pin connector before
proceeding with the power supply connection.
Do not install the fuse before completing the installation
procedure.
!
CAUTION!
Shorten the external supply wires so that the ground (yellow/
green) wire is at least 20 mm (0.8 in.) longer than the live (blue
and brown) wires. This ensures that the ground wire cannot be
accidentally disconnected before life wires.
10 en AEC-AMC2-VDS1 - Installation manual
F.01U.097.255 | V 3.1 | 2008.12 Bosch Sicherheitssysteme GmbH
10. Cable D:
a. Connect D1 to grounding post 10.
b. Connect D2 to the grounding post on the cover.
11. Install the fuse.
12. Close the cover.
i
NOTICE!
Connect the readers and other peripheral devices as described
in the AMC Installation Manuals. Route the device cables
through the knock-outs in the top an right side wall of the
housing, or through the rear of the housing.
Table des matières
Langues :
Autres manuels Bosch Contrôleurs
Bosch
Bosch FW 200 Manuel utilisateur
Bosch
Bosch B443 Manuel utilisateur
Bosch
Bosch Rexroth IndraDrive CsDrive System with HCS01 Manuel utilisateur
Bosch
Bosch AMC2 4W Manuel utilisateur
Bosch
Bosch CL550 Instructions de montage
Bosch
Bosch APC-AMC2-4R4CF Manuel utilisateur
Bosch
Bosch CR 400 Manuel utilisateur
Bosch
Bosch FHP560 Instructions d'utilisation
Bosch
Bosch AMC-4W Manuel utilisateur
Bosch
Bosch Rexroth IndraDrive C HCS03.1 Manuel technique
Bosch
Bosch AMC2 Series Manuel utilisateur
Bosch
Bosch EasyControl CT200 Manuel utilisateur
Bosch
Bosch Rexroth VT-HNC100 3X/S Series Manuel utilisateur
Bosch
Bosch HPC Manuel utilisateur
Bosch
Bosch EasyControl CT200 Manuel utilisateur
Bosch
Bosch REG 73-1 Manuel utilisateur
Bosch
Bosch AMC2 Series Manuel utilisateur
Bosch
Bosch BAT 251 Manuel utilisateur
Bosch
Bosch CC 100 M Manuel utilisateur
Bosch
Bosch BAT 250 Manuel utilisateur
