Bolin Technology VCC-M2H10BI-4FN1 Manuel utilisateur

Dual Output SDI+IP

PTZ Camera

USER MANUAL

Part Two: Network Camera User Manual

Version: SN-IP-09042020

2 
Contents 
PART TWO: NETWORK CAMERA USER MANUAL....................................................................................................................... 3 
NETWORK CONNECTION .......................................................................................................................................................... 3 
PREPARATION ........................................................................................................................................................................... 3 
CHECK BEFORE LOGIN ................................................................................................................................................................. 3 
LOGGING IN TO THE WEB INTERFACE ....................................................................................................................................... 4 
INTRODUCTION TO THE WEB INTERFACE.................................................................................................................................. 5 
PREVIEW ................................................................................................................................................................................. 6 
PAN AND TILT ........................................................................................................................................................................... 6 
PRESETS .................................................................................................................................................................................. 6 
VIDEO ENCODE ......................................................................................................................................................................... 7 
VIDEO TRANSMISSION................................................................................................................................................................. 8 
IMAGE ADJUST.......................................................................................................................................................................... 9 
AUDIO SETTING....................................................................................................................................................................... 12 
ETHERNET.............................................................................................................................................................................. 12 
FIRMWARE UPGRADE ............................................................................................................................................................... 13 
RESET OPTIONS....................................................................................................................................................................... 13 
ACCOUNT .............................................................................................................................................................................. 14 
OSD .................................................................................................................................................................................... 14 
SYSTEM TIME ......................................................................................................................................................................... 15 
 
 

Part Two: Network Camera User Manual

Network Connection

Before accessing a network camera (also known as IP Camera or IPC) from a PC, you need to connect

the network camera to the PC directly with a network cable or via a switch or router.

Use a Shielded Twisted Pair (STP) cable to connect the network interfaces of the network camera and

the PC.

Use Shielded Twisted Pair (STP) cables to connect the network interfaces of the camera and the switch

or router.

Preparation

After you have completed the installation in accordance with the quick guide, connect the camera to

power to boot it. After the camera is booted, you can access the camera from a PC client using Internet

Explorer or a Video Management System (VMS).

The following uses Internet Explorer 11 on a Microsoft Windows 10 operating system as an example.

Check before login

⚫

The camera is powered on and connected to the network switch

⚫

The camera’s IP address is located within the same subnet as the PC

⚫

The PC is connected to the network switch

⚫

The PC’s IP address is located within the same subnet as the camera

⚫

The PC is installed with Internet Explorer 8.0 or higher (Internet Explorer 11 recommended)

⚫

Use default video format setting or set the camera video format to 1080P30 or 1080P25 using

RS485 keyboard (Refer to camera setting menu).

Logging in to the Web Interface

The default static IP address of the camera is 192.168.0.13, and the default subnet mask is

255.255.255.0

The following uses Internet Explorer 11 as an example to describe the login procedure.

1. Browse to the login page by entering the

correct IP (default IP is 192.168.0.13)

address of your camera in the address bar.

2. Enter the username and password, and then

click Login. For the first login, use the

default username admin and password

admin.

•The default password is used for your

first login. To ensure account security,

please change the password after your

first login. You are recommended to set a

strong password (no less than eight

characters).

•The camera protects itself from illegal

access by limiting the number of failed

consecutively, the camera locks

automatically for tenminutes.

NOTE: If your PC/laptop already installed VLC player, you can watch live preview directly after logged in. If

your PC/laptop haven’t installed VLC player yet, you may be prompted to install the VLC player.

Please download and install the correct version of VLC player (it means if your PC/ laptop operating system is

64 bit, you have to download the 64 bit version VLC, if your PC/laptop is 32 bit, so you have to download the 32

bit version VLC), after done the installation, user can re-login to the IP interface and watch the live preview.

Introduction to the Web Interface

1. Preview

•Used to monitor the camera video image

•Used to do camera PTZ control and preset setting

2. Video Encode

•Used to configure the camera video Main and Sub streams video parameter, such as encode

mode, resolution, bit rate, frame rate, I Frame Interval and so on

3. Video Transmission

•Used to configure the camera RTMP streaming, to push the RTMP streaming to the third-party

video platform, like the Youtube, Facebook and so on

4. Image Adjust

•Used to configure the camera image parameter, such as focus, exposure, white-balance, image,

image setting, noise reduction

5. Audio Setting

•Used to configure the camera audio parameter, such as the Encoder Mode, Sample rate and

Bitrate

6. Ethernet

•Used to configure the camera network parameter, can be static IP or DHCP, as well as HTTP port

and RTSP port configuration

7. Firmware Upgrade

•Used to display the camera current version information

•Used to do firmware upgrade

8. Reset Options

•Used to reset the camera image parameter/all parameter to default

•Used to reboot the camera

9. Account

•Used to modify the admin account password

10. OSD

•Used to overlay the time, camera name, logo and text content on the IP video

11. System Time

•Used to setting the time zone and synchronize camera system time with the NTP server

Preview

The preview page is used to watch the live preview

of the camera.

Play/stop Live Preview:

User can click the / button which on the

bottom toolbar, to watch live video or stop the live

video.

Mute:

User can enable or disable the audio of live preview

by click the button on bottom toolbar, while

enabled audio, user can drag the volume bar to

adjust the audio.

Fullscreen:

User can click the button to enlarge the live preview window to full screen, then click button again to

back to normal size, or press PC/laptop “Esc” button to switch back to normal size while in full screen.

Pan and Tilt

Pan and Tilt menu is used to do:

•Camera PTZ control,

•Adjust the pan / tilt / zoom speed

•Set focus mode

Pan/Tilt Speed: to adjust the pan/tilt speed, support 0-24 level selectable

Focus Speed: to adjust the focus speed, support 0-7 level selectable

Zoom Speed: to adjust the zoom speed, support 0-7 level selectable

Speed Reset: To reset the zoom and focus speed to default

PTZ Reset: To reset the PTZ control to default

Standby: If turn on standby switch, the camera will go to standby status, it is not

power off, you can get it back immediately by turn off the standby.

Presets

Presets are predetermined positions that the user can command the camera

to recall quickly.

To add a new preset:

1. Use the control panel and image viewer to pan to the desired Pan, Tilt,

Zoom, and Focus position

2. Click the triangle symbol which in the drop-down list, select a number for

this position (here we select 2 as example)

3. Click the pencil symbol and it will save this position as preset 2

4. Select a preset number and click Go button, the camera will to recall the

position quickly

5. Select a preset number and click Delete button, it will delete this preset

and you can not recall it quickly by GO button

Video Encode

The video encode page is used to configure settings for the compression, format, and data rates for all video

streams produced by the camera

Definitions:

•Encode Mode: The encoding standards that

are available for use (H.264 / H.265)

•Profile: Support baseline, MP and HP mode

•RTSP Address: The RTSP streaming URL

of both main stream and sub stream

•Resolution: (W x H) The number of Pixels

that make up the width of the image (W) by

the number of horizontal lines that make up

the height of the image (H)

•Bitrate: The amount of data transmitted per

second. Measured in Kilobits Per Second

(Kbps). 1000 kbps = 1Mbps

•Framerate: Rate at which image frames are

captured

•Bitrate Control:

oCBR –Constant Bit Rate

oVBR –Constrained Variable Bit Rate.

•I Frame Interval: The shorter the Interval, the

better chance you have of video being of

better quality.

I Frame also can be called “Key Frame”, a "Key

Frame" is an entire and complete and total image, that

is used as a reference for other frames ("images") that

the camera generates

•Main Stream –The main stream, viewed by default on the preview page

oEncode Mode:

▪H.264

▪H.265

oRTSP Address:

▪RTSP main stream address

▪Automatically generated based on the current IP address of the camera

▪You can copy this address and using VLC or other network video compatible player to

receive the RTSP main stream and watch the video.

oResolution:

▪1920x1080

▪1280x720

▪1024x576

oBitrate:

▪The amount of data transmitted per second. Measured in Kilobits Per Second (Kbps).

1024 kbps = 1Mbps

▪0-15360 selectable

oFramerate:

▪Rate at which image frames are captured

▪1-60 selectable

oBitrate Control:

▪CBR –Constant Bit Rate

▪VBR –Constrained Variable Bit Rate.

oI Frame Interval

▪1-100 selectable

•Sub Stream –The sub video stream produced by the camera; this can be disabled by unchecking the

box at the top of this stream’s settings we can switch to sub stream on the top bar of preview page

oEncode Mode:

▪H.264

▪H.265

oRTSP Address:

▪RTSP sub stream address

▪Automatically generated based on the current IP address of the camera

▪You can copy this address and using VLC or other network video compatible player to

receive the RTSP sub stream and watch the video

oResolution:

▪1280x720

▪1024x576

▪640x360

oBitrate:

▪0-15360 selectable

oFramerate:

▪Rate at which image frames are captured

▪1-60 selectable

oBitrate Control:

▪CBR –Constant Bit Rate

▪VBR –Constrained Variable Bit Rate.

oI Frame Interval:

▪1-100 selectable

Video Transmission

This camera supports RTMP

protocol, it can push streaming to

other CDN or cloud platform.

oCheck the RTMP State

Main or Sub Enable button

oCopy and paste the stream

URL from the online

platform

oCopy and paste the Stream

Key (Also known as the

Stream ID) from the online

platform.

Example shows where to copy the

information from YouTube

For Example

URL/Key: rtmp://a.rtmp.youtube.com/live2/6yeu-mg8p-txtm-mvp9-35eb

oClick Save button on camera RTMP page

oAllow a few minutes for the stream to connect. The status on your streaming platform (Such as

YouTube) will change to Live. When this happens, the camera is streaming video Live to

NOTE:

•Must enable audio on Audio Setting page before setup RTMP streaming, otherwise, RTMP streaming

may without audio source.

•Similar steps can be followed to stream to any platform that supports RTMP, such as Facebook, Twitter,

Twitch, etc.)

Image Adjust

Image parameters can be adjusted to control the way the image is captured and displayed

Focus

The Focus menu is used to set the items related to focus

Focus Mode:

You can set to Manual or Auto mode

Digital Zoom:

Turn Digital Zoom ON, 2x digital zoom is activated.

You can set digital zoom to ON or OFF. When turn to OFF, digital zoom does not operate, and only optical

zoom is available. When turn to ON, digital zoom takes over after optical zoom reaches MAX (20x). Up to 40x

can be zoomed digitally.

When digital zoom is available, the resolution decreases

Exposure

The Exposure menu is used to set the items related to exposure.

Exposure Mode

Auto: The exposure is adjusted automatically using the values set for EX-COMP (Exposure

Compensation).

Manual: Adjust the GAIN, electronic shutter speed (SPEED), iris (IRIS) manually.

Iris Priority: Iris Priority mode. The exposure is adjusted automatically using the values manually set

for iris (IRIS) and EX-COMP.

Shutter Priority: Shutter Priority mode. The exposure is adjusted automatically using the values

manually set for electronic shutter speed (SPEED) and EX-COMP.

Brightness Priority: Bright Priority mode. The exposure is adjusted automatically using the values

manually set for electronic brightness level.

When you select one from various exposure modes, some of the following setting items that can be adjusted.

Gain: Adjustable from 0 to 15 by drag the setting bar (not available in Auto, Iris, Shutter, Brightness mode)

Shutter: Adjustable from the following

1/30, 1/60, 1/90, 1/100, 1/125, 1/180, 1/250, 1/350, 1/500, 1/725, 1/1000, 1/1500, 1/2000, 1/3000, 1/4000,

1/6000, 1/10000 (not available in Auto, Iris, Brightness mode)

Iris: Adjustable from 0 to 13 by drag the setting bar (not available in Auto, Shutter, Brightness mode)

Anti-flicker: Enable it before you to select, 50Hz and 60 Hz selectable

Brightness: Adjustable from 0 to 27 by drag the setting bar (not available in Auto, Manual, Iris, Shutter mode)

White-Balance

The White-Balance menu is used to set the items related to white balance.

White Balance Mode

Auto: This mode computes the white balance value output using color information from the entire

screen. It outputs the proper value using the color temperature radiating from a black subject based on

a range of values from 2500K to 7500K. This mode is the initial setting.

Indoor: 3200K Base Mode

Outdoor: 5800K Base Mode

Table des matières

Autres manuels Bolin Technology Caméra de sécurité

Bolin Technology

Bolin Technology FEX Series Manuel utilisateur

Bolin Technology

Bolin Technology SD500 Series Manuel utilisateur

Bolin Technology

Bolin Technology FEX30BHD-RNP2 Manuel utilisateur

Bolin Technology

Bolin Technology D Series Manuel utilisateur

Bolin Technology

Bolin Technology VCC-8-4K12S-SM Manuel utilisateur

Bolin Technology

Bolin Technology VCC-8HD20S-2SMC Manuel utilisateur

Bolin Technology

Bolin Technology KBD-1010 Manuel utilisateur

Bolin Technology

Bolin Technology SD5SN-M-10162017 Manuel utilisateur

Bolin Technology

Bolin Technology D Series Manuel utilisateur

Bolin Technology

Bolin Technology EX1030BHD-L5NA Manuel utilisateur

Bolin Technology

Bolin Technology VCC-2HD10S-SN Manuel utilisateur

Bolin Technology

Bolin Technology VCC-4KHDB-M-11142018 Manuel utilisateur

Bolin Technology

Bolin Technology BC-9 Series Manuel utilisateur

Bolin Technology

Bolin Technology 2 Series Manuel utilisateur

Bolin Technology

Bolin Technology UCC-2HD10BT-U32 Manuel utilisateur

Bolin Technology

Bolin Technology VCC-8-4K20S-3SM Manuel utilisateur

Bolin Technology

Bolin Technology D Series Manuel utilisateur

Bolin Technology

Bolin Technology VCC-8-4K20S-3SMB Manuel utilisateur

Bolin Technology

Bolin Technology 8 Series Manuel utilisateur

Bolin Technology

Bolin Technology VCC-7HD20S-3SMC Manuel utilisateur

Bolin Technology

Bolin Technology BC-7 Series Manuel utilisateur

Bolin Technology

Bolin Technology EX1000 Series Manuel utilisateur

Bolin Technology

Bolin Technology VCC-7 Series Manuel utilisateur

Bolin Technology

Bolin Technology 7 Series Manuel utilisateur

Manuels Caméra de sécurité populaires d'autres marques

Okina USA

Okina USA SIR36-870VF650LP Manuel utilisateur

Divio

Divio NDR155PA Manuel utilisateur

Canon

Canon VB-C500D Manuel utilisateur

Easy Access

Easy Access EasyGuard Manuel utilisateur

Vivotek

Vivotek FD9389-EHV-v2 Manuel utilisateur

TUYA

TUYA COSMO W2 Manuel utilisateur

Eusso

Eusso UNC7500-IR Guide de configuration

urmet domus

urmet domus 1096/204 Manuel utilisateur

VC VC20 series Manuel utilisateur

Axis

Axis Q1614 Manuel utilisateur

ieGeek

ieGeek DD201 Manuel utilisateur

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manuel utilisateur

Vicon

Vicon V662-D-1 Mode d'emploi

Grundig

Grundig GCH-K0274P Manuel utilisateur

Lorex

Lorex VANTAGE LBC7032 Manuel utilisateur

4xem

4xem WPT Manuel utilisateur

Samsung

Samsung SCV-3082 Manuel utilisateur

Vitek

Vitek VTC-C544 Manuel utilisateur