Bodet CHRONOLED Manuel utilisateur
1
CHRONOLED
Timer/Stopwatch Display
Installation and operating manual
BODET SA
1 rue du Général de Gaulle
49340 TRÉMENTINES FRANCE
Tel. 02 41 71 72 99
Fax 02 41 71 72 02
www.bodet-sport.com Ref. 606985G
Upon receipt, always check the product for damage during shipment. If any is found, you may file a damage claim with the carrier.
2
Table of contents
I - Overview .................................................................................3
II - Mechanical installation ...........................................................4
II.1 Opening the Chronoled ........................................................................4
II.2 Wall mounting.......................................................................................4
II.3 Mounting on car roof rack holder (Chronoled 15 and 25 only).............5
II.4 Mounting on tripod stand (Chronoled 15 and 25 only) .........................6
III - Electrical installation..............................................................7
III.1 Power supply.......................................................................................7
III.2 Connecting a double-sided Chronoled................................................7
III.3 Conguring the dips ............................................................................7
III.4 Chronoleds in series............................................................................8
III.5 Pairing an HF remote control ..............................................................8
IV - Paramater Setting.................................................................9
IV.1 Main menu..........................................................................................10
IV.2 CHRO menu: timer/stopwatch settings .............................................. 11
IV.3 SCORE menu: score entry.................................................................13
IV.4 TIME menu: time setting ....................................................................13
IV.5 PROG menu: luminosity, relays and time base adjusments ..............15
IV.6 TECH menu: ......................................................................................16
IV.7 TEST menu: panel test and version display.......................................19
V - Types of time synchronisation...............................................19
VI - Technical features................................................................20
3
I - Overview
The Chronoled is an outdoor count up/countdown timer.
- Very high luminosity SMD LED with 6 digits and 3 dots.
- Display: time of day with second, timer (count up, countdown, day), score.
- Supply voltage: 110/230 v AC.
- Aluminum housing.
- Available Led colours: Red (R).
- Automatic luminosity management according to light conditions (sunny,
cloudy or night time). On 2 sided units, each side manages its own brightness.
CAUTION : installation and maintenance of this equipment must be performed by a
authorized person. This is a dual voltage product that can be powered power by 110v
AC or 240v AC. The installation must comply with the IEC 364 standard (NFC 15-100
for France).
A 16 Amps circuit breaker (phase + neutral) must be installed in the power source line
to protect the equipment and must be tripped o when performing maintenance. The
equipment must be powered up only after the installation has been completed.
Any modication on the product cancels the warranty.
4
II - Mechanical installation
II.1 Opening the ChronoLed
To access the programming push-buttons, remove the 2 screws (Chronoled
15 and 25) or the 4 screws (Chronoled 45) on the right side to remove the side
cover.
If needed, access to other elements is possible (power supply, driver board,
module wiring...) by removing the glass front cover. Slide the glass sideways 5
to 10 cm, then lift it up and pull it toward you to extract it from the lower prole
of the Chronoled.
II.2 Wall mounting
Fasten the unit to the wall using 4 (Ø6) screws for the Chronoled 15 and 25 or 4
(Ø8) screws for Chronoled 45 (the screws are not supplied) and the appropriate
wall anchors (wall plugs).
Note: see last page.
5
II.3 Mounting on car roof rack (Chronoled 15 and 25 only)
1/ Assemble the roof rack brackets as shown in B and D.
2/ Fasten the Chronoled (or both Chronoleds if double side) on the brackets as
in A.
3/ Install the Chonoled-brackets assembly on the roof rack bars using the the
hand-screws as in C
Caution : when the Chronoled is mounted on the roof, drive the vehicle slowly (60 km/h
maximum).
B
Screw TH M6x16
Nut HU M6 Zn
Tooth lockwasher Ø6 Zn
355,00
A
BC
D
Thickness : 43 mm
Width : 59 mm
Max section of roof bars :
A
Nut HU M6 Zn Screw H M6x16
Flat washer Ø6 Zi Flat washer Ø6 Zi
Screw TH M6x16
Tooth lock washer Ø6 Zn
Nut HU M6 Zn
C
SCREW H M6x60 Zi
Star button for screw M6
Chronoled gallery holder flange S/A
565,00
Gallery bracket
Mounting with Chronoled 15
800,00
Mounting with Chronoled 25
6
II.4 Mounting on tripod stand (Chronoled 15 and 25 only)
1/ Fasten the Chronoled bracket onto the base plate of the stand with the 4
screws as in B.
2/ Fasten the Chronoled (or both Chronoleds if double side) on the bracket with
4 screws as in A.
A
Flat washer Ø6 Zi
Flat washer Ø6 Zi
HU nut M6 Zn Screw H M6 X 20 ZI
B
Screw H M8 X 20 ZI
Flat washer Ø8 Zn
Flat washer Ø8 Zn
Nut HU M8 Z
C
Double Sided mount
A
B
Mounting stand
Stand baseplate
Stand bracket
C
7
III - Electrical installation
III.1 Power supply
The power supply is a dual voltage unit. The
selection of the input voltage is done by mean
of a slide switch located on the side of the
power supply. By default the selected input voltage is 230v 50/60Hz. To set it
for 115v, rst remove the digit card in front of the power supply and then the Z
shape bracket to have access to the switch.
Connect the Chronoled power cord to 115/230v AC mains or the 12v DC power
inverter (cigarette lighter) if it is used.
Note 1: remove the glass to gain access to the power supply unit (see § II. 1).
Note 2: the adhesive protection delivered must be stuck above the terminal strips of the
power supply at the end of the wiring, preventing direct contact with hazardous voltages.
III.2 Connecting a double-sided Chronoled
In the case of a double-sided Chronoled, one panel must be master and the
other one salve. A synchronization cable kit made of two sections must be used.
The male section connects to the RS485 connector of the master and the female
section to the slave. Connect the 2 sections together.
III.3 Conguring the dips
The dips are set at the factory, however if several Chronoleds are to be connected
together then dips 3 to 5 need to be set according to following table (next page).
8
Clock type Dip 1 Dip 2
CHRONOLED 1 0
Clock type Dip 1 Dip 2 Dip 3 Dip 4 Dip 5
MASTER HMT LED 0 0 / / /
HMS LED 0 1 / / /
SLAVE
Slave 1 1 0 0 0 1
Slave 2 1 0 0 1 0
Slave 3 1 0 0 1 1
Slave 4 1 0 1 0 0
Slave 5 1 0 1 0 1
Slave 6 1 0 1 1 0
Slave 7 1 0 1 1 1
RS 485 connector for slave sync.
III.4 Chronoleds in series
Up to 8 Chronoleds can be connected in series (1 master and up to 7 slaves).
- Set one Chronoled as master via the dips, then all the other Chronoled as
slave (each slave Chronoled must have a unique number). See table above.
- Connect the RS485 synchronization cable to the RS485 connector of each
Chronoled. See the above illustration.
III.5 Pairing an HF remote control
Using the HF remote control to operate the Chronoled requires pairing. This operation is
performed in the factory.
Pairing is accomplished during a limited time of 30sec after powering up the
Chonoled by holding down the [T] key for 1 sec, 88 is then displayed.
Unpairing a remote control is performed identically to pairing.
Note: everytime a Chronoled is powered up, a remote control which is already
paired is inactive for 30 seconds.
9
[Sel] push button (inside Chronoled only)
- To call the main menu (chro/time/scor/prog/test) hold down this push-button.
- To exit a menu, hold down this push-button.
- Press briefly on this push-button to validate the menu or the parameter
previously selected.
[+] push button (inside Chronoled only)
- While displaying a menu, press this button to select the next menu or
parameter.
[S] Remote control key
- While displaying a menu, press this key briefly to validate the menu or the
parameter previously selected.
– In timing mode, press this key to start the timer, and press this key again
stop the timer.
[R] Remote control key
- Selects the next menu or next parameter.
- In timing mode, resets the timer when it is stopped.
[M] Remote control key
- Hold down this key to call the main menu (chrono / time / scor / prog / test).
- Press this key briefly to exit a programming menu.
S : ‘S’ key
+ : ‘R’ key
M : menu key
T : version / Test key
HF remote control
Sel
+
Programming push-buttons
IV - Parameter Setting
To set the parameters of the Chronoled, use the 2 push-buttons located inside
the Chronoled or the HF remote control. The push-buttons are accessible by
removing the right side of the Chronoled.
Caution: to prevent short circuits, do not insert any metallic objects in the Chronoled.
10
[T] Remote control key (called test key)
- Hold down this key for 1 sec. to perform a display test and to display the
software version number.
Note on remote control and Chronoled keys
- During the process of data entry, if no key is pressed for 30 sec, automatic
menu exit is performed, without validating the currently selected parameter.
A parameter is validated only after pressing [S].
IV.1 Main menu
The main menu provides access to all setting functions of the Chronoled display.
It contains 5 menus :
CHRO : sets timing functions (count up/count down).
TIME : sets time of day and date.
SCOR : manages 2 scores, Home and Visitors, from 0 to 99.
PROG : sets brightness of the display LEDs, sets a countup/countdown
loop, sets the time of the relay at end of timing.
TECH : Allows the selection of the display mode12/24h and the display
order month/day (31.12 or 12.31), to set the time synchronisation
mode, to set the options of time zone and summer/winter change-
over, to modify the time base, to select the temperature unit (C or
F), temperature display mode, to apply an offset to the tempera-
ture and the humidity and to set the channel of the HF transmitter.
This menu is for technician only.
TEST : tests the display panel to check that each LED runs properly and
displays the software version number.
Just validate one of these first 3 menus (CHRO, SCOR
and TIME) to display the corresponding mode.
For example, to display the time when the Chronoled displays
a time countdown, just enter the TIME menu and validate.
1. The display is idle while displaying the time. Press [M] on
the remote control (or the [Sel] key for 1 sec) to call the main
menu.
2. The rst menu displayed is the CHRO menu, to go to the
next menu (tIME), press the [R] key.
3. Press [S] to validate the chosen menu. Conversely, pressing
[M] lets you exit the menu (or the [Sel] key for 3 sec).
Table des matières
