Bock Water heaters 32E Mode d’emploi

TO THE CONSUMER:

Read these and all com -

po nent in struc tions.

Please keep for fu ture

reference. Please re -

mem ber to return the

registration card.

Waranty, registration

card & parts list in clud ed.

TO THE NSTALLER:

Please attach these in -

struc tions next to the

water heater.

BOCK RES DENT AL O L-F RED

WATER HEATERS

Model numbers: 32E, 32PPC, 33E, 50ES,

51EC, 51PPC, 120E

WARN NG:

Improper installation, adjustment, alteration, ser vice

or maintenance can cause serious in ju ry or prop -

erty damage. Refer to this man u al. For as sis tance

or additional in for ma tion, con sult a qual i fied in stall er

or service agency.

WARN NG:

If the information in these instructions is not fol -

lowed exactly, fire or explosion may result and can

cause property damage, personal in ju ry or death.

WARN NG:

Follow minimum combustible clearance as noted

on wa ter heater label. Do not in stall on com bus ti -

ble flooring (see Figure 2, Page 3). In stall in ac cor -

dance with all lo cal codes. In the ab sence of local

codes, re fer to NFPA 31.

CAUT ON:

The recommended temperature for normal residen -

tial use is 120°F. The dial on the aquastat does not

always reflect the outcoming water tem per a ture,

which could occasionally exceed 120°F. The vari a -

tion in outcoming tem per a ture could be based on

factors including but not limited to us age pat terns

and type of installation. Test your water at the tap

nearest to the water heater. (See page 5 for mea -

sur ing the outcoming water tem per a ture).

WARN NG:

otter water increases the risk of scald injury. Be -

fore changing the temperature setting, read the

in struc tion manual. Tem per a tures at which injury oc -

curs vary with the in di vid u al’s age and length of

ex po sure.

The slower reaction times of children, elderly and

physically or mentally impaired persons in creas es

the scald ing hazard to them. It is rec om mend ed low er

wa ter temperatures be used where these sit u a tions

exist.

ouseholds with small children or invalids may re -

quire a tem per a ture setting less than 120°F to pre vent

accidental contact with hot water.

To lower water temperature use point-of-use tem -

per a ture limiting devices.

WARN NG:

Flammable vapors may be drawn to this wa ter heat -

er from other areas of the struc ture by air currents.

Do not store or use any flam ma ble liquids in the

vicinity of this heater.

WARN NG:

Water heater blankets may not be used on the

heater and may cause fire, asphyxiation, per son al

injury or death.

Bock Water Heaters, nc.

110 South Dickinson Street • Madison, W 53703

Phone: 608/257-2225 • Fax: 608/257-5304 • www.bockwaterheaters.com

NSTALLAT ON, OPERAT ON &

MA NTENANCE N STRUC T ONS

23420 Rev 10 (9/17)

– 2 –

THIS MANUAL HAS BEEN PREPARED TO ACQUAINT YOU WITH THE IN STAL -

LA TION, OP ER A TION, AND MAINTENANCE OF YOUR WATER HEATER AND

TO PRO VIDE IM POR TANT SAFETY INFORMATION.

Read all instructions thoroughly before attempting installation or operation of the

water heat er. Keep these and all component instructions for future ref er ence.

The manufacturer of this water heater will not be liable for any damages caused

by failure to comply with the installation and operating instructions outlined on the

fol low ing pages. These instructions are a guide for the correct installation of the

water heater.

If the installer lacks the necessary skills or has difficulty following the

di rec tions, do not pro ceed but get help from a qualified person for that part of the

installation that is not un der stood.

Local plumbing and electrical codes must be followed in the installation of this

water heater. In the absence of a local code use the UNIFORM PLUMBING CODE

and the NFPA Code. Local codes may supersede instructions in this installation

manual.

When two or more burners are used, each unit should have a separate

supply line to the fuel pump to prevent nuisance lockouts caused by one or both

pumps starving for oil. If this is not possible, the use of a priority

control is recommended.

Check new equip ment to see if all com po nents are in good con di tion.

The wa ter heater and oil burner may be shipped as sep a rate units. The aquastat

and im mer sion well may be packed with the oil burner.

The new water heater re quires fuel (#I or #2 heat ing oil), electricity and should be

close to the chim ney and water supply. Lo cate the heater near a floor drain if pos -

si ble for easy main te nance and protection if trouble should occur. Allow ample

space around the heater for servicing (see combustible clearance warning, page

1). Ad e quate air for com bus tion must be available. NOTE: Locate the heater so it

is not subject to physical damage by moving vehicles or possible flood ing.

CONSUMER

RE SPON SI BIL I TIES

MULTIPLE BURNER

INSTALLATION

SELECT THE RIGHT

LOCATION

FIGURE 1

Check for exhaust fans in

the heater room or ad ja -

cent ar eas which draw

com bus tion air away from

heater. THE HEATER

MUST HAVE COM BUS -

TION AIR TO OP ER ATE.

DO NOT INSTALL THE WATER HEATER ON COM BUS -

TI BLE FLOORING (see Figure 2).

Refer to NFPA 31 or

con tact Bock Wa ter Heat ers with questions con cern ing

prop er floor ing ma te ri als.

Minimum clearance to combustible con struc tion is:

SIDES 6"; BACK 6"; FRONT 24". The in stal la tion of

this water heater must con form with local codes and

or di nanc es. In the absence of local codes, the in stal -

la tion must comply with the Na tion al Fire Pro tec tion

As so ci a tion (NFPA 31) Code.

FAILURE TO FOLLOW

THESE INSTRUCTIONS

OR ALL APPLICABLE

BUILD ING CODES AND

REG U LA TIONS VOIDS

THE WAR RAN TY ON THIS

WATER HEAT ER.

FIGURE 2

CAUTION!! Scalding injury and/or water dam age can

occur from ei ther the manual lifting of the lever or the

normal op er a tion of the T&P valve if it is not piped to a

proper drain. If the valve fails to flow water or reseat, call a

plumb er.

– 3 –

CONNECT WA TER

PIPING

Connect the water piping, being careful not to apply heat to the heater

nipples. Install di elec tric unions and shut off valves on both hot and cold water

lines.

Model 33E is equipped with an inlet flow diverter installed

in the tank. This model contains decal next to the inlet

(shown to the left). The purpose of this diverter is to help

keep the tank bottom free of sediment by aiding tank

flushing. The index line on the diverter nipple must be

aligned with the arrow on the decal (left) to function

properly. Do not allow the diverter to rotate out of position

when tightening the inlet fittings.

NOTE: INDEX LINE ON INLET NIPPLE

MUST BE ALIGNED WITH ARROW ON

DECAL. HOLD INLET NIPPLE WHEN

TIGHTENING FITTINGS. ROTATING

NIPPLE COULD DRASTICALLY REDUCE

PERFORMANCE.

Inspect the incoming water line for check valves or water pres sure re duc ing

valves. Any type of check valve may cause pres sure to build up in the heater and

cause tank failure. If the heat er is in stalled in a closed system or if backflow

preventers and pressure reg u la tors are in stalled, add an ex pan sion tank. Do not

try to heat hard water. Install a water soft en er if the heat er is being used in a hard

wa ter area (water hardness more than 7 grains).

An ap proved temperature and pressure (T&P) relief valve is factory installed in the

opening provided in the upper right hand side of the heater. Pipe the T&P to within

6" of the floor or to a floor drain with a free flowing drain pipe.

Install a vent connector between the chimney and the water heater. The size of

the vent connector shall be acceptable based on the rise in height of the connec-

tor and the water heater input.

If it is necessary to connect to an existing vent connector, be sure the connector

utilized is large enough to ac com mo date the products of com bus tion of all units

at tached to it. When utilizing an oth er connector, run in at 45° angle (see Figure 1).

Install a draft regulator con trol only if nec es sary. Overfire draft should not be pos -

i tive. Breech draft should be -.03” W.C. min i mum to -.05” W.C. maximum; CO2

should be a minimum of 11% with zero smoke on the Bacharach scale.

The oil burner is equipped with a primary relay. An aquastat with immersion

well is packed with the burner. The thermostat is factory set at 120°F for residen-

tial use (see caution on page 1 regarding temperature vari a tions). Install the

immersion well with the aquastat and check the bulb length (see “Burner &

Controls” section, page 10).

Remove the cardboard core from the burner opening. Mount the burner on stud

bolts and place the gasket (sup plied) between the burner flange and the heater.

Secure the burner to the heater with 1/4 -20 nuts (supplied). Open the inspection

door on the heater and check the burner tube with a mirror before firing to

be sure the open ing is not blocked (see Maintenance and Service sections on

pages 6 and 7 for troubleshooting).

MOUNT THE OIL

BURN ER

CONNECT TO

CHIMNEY

– 4 –

All wiring must comply with applicable codes and ordinances. The primary relay is

wired to the burner at the factory. Install the aquastat well in the 3/4" tapping at

the front of the heater. Be sure the sensing bulb is inserted all the way into the

well. For Honeywell aquastats, tighten the screw on top of the aquastat to secure

the control to the well. For Carlin EZ-Temp aquastats, refer to the pre-packaged

installation guide for proper set-up procedure. Refer to drawings for correct

models. Connect the power supply to the aquastat and run through a fused dis -

con nect switch (attached to heater in field). See Figure 1.

A properly sized and rated oil filter shall be installed in the oil supply line

(NFPA 31, 4.5.4).

Gravity System: The oil burner is normally equipped with a single-stage pump

equipped for one line (gravity) flow. Use minimum 3/8" O.D. soft copper tubing and

attach with flared fit tings. DO NOT USE COM PRES SION FITTINGS. Install the

shut off valve and oil filter in the oil line. Follow the pump man u fac tur er’s instruc-

tions (attached to the pump).

Lift System: The burner should be ordered with a 2-stage pump. Run a 2-line

system (suc tion and return lines). Install the bypass plug according to the

instructions attached to pump (plug is in a bag with an instruction sheet).

For any horizontal run exceeding the maximum length specified in Figure 3, or any

lift of more than 10 feet, a booster pump must be used. Boost er pumps must be

installed as close to the oil supply tank as possible. Suction and return lines

should be the same diameter and both go within 6” of the bottom of the tank. The

return line should stop slightly above the suction line. Use a minimum of fittings.

Make bends in the tubing with as large a radius as possible. DO NOT USE

COM PRES SION FITTINGS. Caution must be used in the final connection to the

burner so as not to strain the fuel unit. Before attaching the tubing to the burner,

form a coil in the tubing to minimize any vibration. State and local codes must be

followed.

1. Fill the tank with water, opening a hot water faucet to allow trapped air to

escape from the heater. Open the cold water inlet valve. Shut off each faucet as it

delivers water that is free of air. Inspect for leaks. Never operate an empty or

partially full heater.

CONNECT THE OIL

LINE

WARNING!! WHEN YOU

INSTALL THE BYPASS

PLUG YOU MUST RUN A

TWO-LINE SYSTEM.

CONNECT THE

ELECTRICITY

Your log (or one similar to this) must be filled out as follows:

Date Time Test person’s name Set temp. oF Outlet temp. oF

FIGURE 3: MAXIMUM LIFT & HORIZONTAL RUN

1-Pipe Single Stage Horizontal 2-Pipe Two-Stage Horizontal

System Pump Run System Pump Run

3/8” O.D. 1/2” O.D. 3/8” O.D. 1/2” O.D.

Lift Tube Tube Lift Tube Tube

0’ 65’ 100’ 0’ 75’ 100’

4’ 45’ 100’ 4’ 64’ 100’

7’ 31’ 100’ 7’ 55’ 100’

8’ 16’ 64’ 10’ 47’ 100’

PLACE THE WATER

SYSTEM IN

OPERATION

– 5 –

Warning: Handhole

cover may loosen

during ship ping –

check for tightness

before putting heater

in operation.

2. To place burner in operation, follow the instructions provided with the burner.

3. Set the pump pressure to 100 PSI for Wayne, Carlin and Beckett burners and

150 PSI for Riello burners.

4. Adjust the burner combustion air in accordance with the burner manufacturer’s

instructions. Us ing com bus tion in stru ments, check the C02 and smoke. The C02

should be at least 11% min i mum with zero smoke on the Bacharach scale.

5. While the burner is operating, disconnect one of the yellow cad cell wires.

Check to see that the burner control locks out in the time specified on the control.

Reattach the wire and reset the control. The burner should restart. Note: You may

have to wait a minute before resetting the control.

6. The thermostat is factory set at 120°F for residential use. (See caution on

page 1 re gard ing tem per a ture variations. It is the responsibility of the homeowner

and installer to verify that the installer follows the rec om mend ed quantitative

testing for measuring the outcoming water tem per a ture. To make sure that the

system works properly after installation and in the future, it is rec ommend ed that

the heater’s per for mance be measured and monitored. Run water out of the tap

nearest the heater until it comes out warm. Using a calibrated thermometer, take

a mea sure ment. If the water is not at a suitable tem per a ture for the installation,

have a qual i fied service person adjust the aquastat. Contact Bock for further

information on the ther mom e ter if need ed.

WARNING: Hydrogen gas can be produced in a hot water system served by

a heater that has not been used for a long period of time (generally two

weeks or more.) Hy dro gen gas is ex treme ly flammable. To reduce the risk of

injury, open the hot water faucet at the highest lo ca tion in the house for

several minutes before using any electrical ap pli ance connected to the hot

water system. If hy dro gen is present, there may be an un usu al sound such

as air escaping through the pipe as the water begins to flow. Do not smoke

or allow an open flame near the faucet at the time it is open.

1. Follow the burner manufacturer’s instructions for proper maintenance of the oil

burner.

2. EVERY SIX to 12 MONTHS. Drain water from the heater tank and inspect for

sed i ment or lime ac cu mu la tion. Flush out if necessary. If lime has accumulated,

remove with a com mer cial compound for dissolving lime or by scraping through

the hand hole opening (if supplied). Check water softening equip ment if lime is

found in the tank. DO NOT ATTEMPT TO HEAT HARD WA TER. (See

maintenance label on heater.)

3. Change the magnesium anode rods every six to 12 months or when they

are re duced to 3/8” diameter (see maintenance label on heat er).

4. Open the relief valve test lever to flush out the tank. Make sure it reseats itself.

5. If the heater is to be shut off in cold weather, drain the tank to prevent freezing.

1. Check the fuel supply, electrical wiring and fuses, and make sure temperature

control is calling for heat.

2. If the burner fails to operate, call a qualified local service provider.

SERVICE

MEASURING

THE

OUTCOMING

WATER

TEMPERATURE

MAINTENANCE

– 6 –

L4080B

L4006A

FIGURE 7: Honeywell L4006A w/ L8080B

For Models: 50, 120E

FIGURE 5: Beckett or Wayne burner w/ Carlin EZ-Temp

For Models: 32, 33, 50, 51, 120

FIGURE 6: Honeywell L4103A-1142

For Models: 32, 33, 51

FIGURE 6 N TES:

Set point 120°igh limit: 190°

Aquastat:

120° set point

15° differential

WIRING

FIGURE 4: Carlin burner w/ Carlin EZ-Temp

For Models: 32, 33, 50, 51, 120

(see burner manufacturer’s instructions for 20e;

60200 primary w/ three wire harness)

– 7 –

ITEM DESCRIPTION

1. Cold Water Inlet Dip Tube

(N/A 33E)

2. Plastic Cap

3. Magnesium Anode Rod

(aluminum avaliable)

4. Name Plate/Rating Label

6. Immersion Well & Aquastat

8. Drain Valve

9. Mounting Bracket Gasket

10. Burner Mount ing Bracket

(part of jacket assembly on Models

32E through 51 Series; sold

sep a rate ly on 120E)

11. Bottom Pan

12. Combustion Chamber Sleeve

13. Com bus tion Chamber

14. Inspection Block

15. Inspection Door

16. Heater Jacket

17. Tank

18. Hot Out Nipple

51 Series: 1”

AlI others: 3/4”

50ES: N/A

19. Top Pan

20. Burner

OIL FIRED WATER HEATER BOCK TANK ASSEMBLY

PARTS LIST

When ordering repair parts, always give

the part name, model num ber, size and

serial number.

Handhole cover plate and gasket

(for 50ES only) not shown.

– 8 –

LIMITED WARRANTY FOR OIL-FIRED WATER HEATER

Bock Water Heaters, Inc.

110 S. Dickinson Street

Madison, WI 53703

Phone: 608-257-2225

WHAT DOES THIS LIMITED WARRANTY COVER?

This limited warranty applies only to the original consumer purchaser.

General Defects and Malfunctions: This warranty covers defections and malfunctions in your new

water heater for a period of one year from the original installation date. We will repair or replace, at our

option, any defective or malfunctioning component of the water heater. This limited warranty will terminate

if you sell or otherwise transfer the water heater, or the water heater is installed at a location different

from its original installation location.

Tank and Heat Exchanger: We also warrant that the tank and heat exchanger will not leak due to

defective materials or workmanship for five years from the date of original installation or from date of

manufacture in the event the Limited Warranty Registration Card was not completed and returned to

manufacturer. If the tank and heat exchanger is leaking and we have verified that the leak is due to a

defect in materials and workmanship, we will replace the tank with a tank that is the nearest Bock model

available at the time of replacement. If a replacement tank is provided, it will remain warranted under this

section as if it were the original tank. For example, if we send you a replacement tank under this limited

warranty two years after the original installation date, then the replacement tank will remain warranted for

the remaining three years after the original installation date.

HOW DO YOU GET SERVICE UNDER THE LIMITED WARRANTY?

In order for the warranty period to begin on the date of installation, you must return the warranty

registration card attached below within 30 days of purchasing the water heater. You may also register

your water heater online at www.bockwaterheaters.com. You must have a copy of the original sales

receipt at the time you request service. Failure to return the warranty registration card and provide a copy

of the sales receipt will result in the warranty period beginning from the date of manufacture.

To get service under this limited warranty you should contact either the dealer or installer. If dealer or

installer is unknown you can contact us via e-mail at warranty@bockwaterheaters.com or call us Monday

through Friday between the hours of 8 o’clock a.m. to 5 o’clock p.m. Central Time at the following

number: 1-608-257-2225.

You can also write us at the following address:

Bock Water Heaters, Inc.

Warranty Support Group

110 S. Dickinson Street

Madison, WI 53703

We will respond not later than ten days after we have received your request for service.

– 9 –

WHAT DOES THIS LIMITED WARRANTY NOT COVER?

This limited warranty does not cover water heaters that are or were:

• Incorrectly installed, especially where the installation violates state or local plumbing, housing or

building codes.

• Operated at inappropriate settings, excessive pressures or temperatures.

• Exposed to adverse local conditions and specifically sediment or lime precipitation in the tank or

corrosive elements in the atmosphere or unacceptable water quality.

• Installed outside the United Sates or Canada.

• Acidentally damaged.

Also, we will not cover the following charges, costs and losses:

• Any freight or delivery charges.

• Any removal or installation charges.

• Charges to return the water heater or part to the manufacturer.

• Water damage, loss or damage to property, inconvenience or loss of use.

WHAT WILL VOID THE LIMITED WARRANTY?

If you do any of the following, you will void this limited warranty:

• Fail to retain an original copy of your sales receipt.

• Fail to retain the actual rating plate from the water heater.

• Alter or remove the serial number.

• Transfer or sell the water heater.

• Remove the water heater from its original location and install it somewhere else.

• Fail to follow the care and maintenance instructions provided with the water heater.

• Remove the anode rods.

• Fail to inspect and replace the anode rods (you must retain and present your paid receipts as proof

of anode rod replacement).

• The use of any burner and/or controls other than the ones specified for the water heater by Bock

Water Heaters Inc.

HOW DOES STATE LAW RELATE TO THIS LIMITED WARRANTY?

This is a limited warranty. WE MAKE NO OTHER EXPRESS WARRANTIES WITH RESPECT TO THIS

WATER HEATER. We will not assume, nor authorize any person to assume for us any other liability in

connection with the sale or operation of this water heater. ANY IMPLIED WARRANTIES, INCLUDING

MECHANTABILITY OR FITNESS FOR A PARTICULAR APPLICATION, IMPOSED ON THIS SALE

UNDER THE LAWS OF THE STATE OF SALE ARE LIMITED TO ONE YEAR. This warranty gives you

specific legal rights, and you may also have other rights which vary from state to state. Some states do not

allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.

WE WILL NOT BE RESPONSIBLE FOR WATER DAMAGE, LOSS OF USE OF THE UNIT, INCONVEN-

IENCE, LOSS OR DAMAGE TO PERSONAL PROPERTY, WHETHER DIRECT OR INDIRECT, AND

WHETHER ARISING IN CONTACT OR TORT. Some states do not allow the exclusion of incidental or

consequential damages, so the above exclusion may not apply to you.

Bock Water Heaters, Inc. • 110 South Dickinson Street • Madison, WI 53703

Telephone 608-257-2225 • Fax 608-257-5304

www.bockwaterheaters.com

Ce manuel convient aux modèles suivants

Table des matières

Langues :

Autres manuels Bock Water heaters Chauffe-eau

Bock Water heaters

Bock Water heaters PowerGas 32PG Manuel utilisateur

Bock Water heaters

Bock Water heaters 75-76SKG Manuel de service

Bock Water heaters

Bock Water heaters ODOT125 Manuel de service

Bock Water heaters

Bock Water heaters Commercial/Industrial Water Heaters Manuel utilisateur

Bock Water heaters

Bock Water heaters 80030 Manuel utilisateur

Bock Water heaters

Bock Water heaters 38W-155 Manuel utilisateur

Bock Water heaters

Bock Water heaters High Efficiency Condensing Gas Water Heaters Manuel utilisateur

Bock Water heaters

Bock Water heaters Turboflue 541PG Manuel utilisateur

Bock Water heaters

Bock Water heaters Residential Oil-Fired Water Heater Manuel utilisateur

Bock Water heaters

Bock Water heaters 20e Manuel

Bock Water heaters

Bock Water heaters CE050 Manuel de service

Bock Water heaters

Bock Water heaters HEC Series Manuel utilisateur

Bock Water heaters

Bock Water heaters EZ FIT Atmospheric Gas EZ 75-76N Manuel utilisateur

Bock Water heaters

Bock Water heaters EZ 75-76PDV-C Manuel de service

Bock Water heaters

Bock Water heaters 80STE Manuel utilisateur

Bock Water heaters

Bock Water heaters EZFIT Manuel de service

Bock Water heaters

Bock Water heaters Gas 120PG-BCS Manuel utilisateur

Bock Water heaters

Bock Water heaters OT125 Manuel de service

Bock Water heaters

Bock Water heaters LCE6-1 Manuel utilisateur

Bock Water heaters

Bock Water heaters Electric Water Heaters Manuel utilisateur

Bock Water heaters

Bock Water heaters CE050 Manuel utilisateur

Bock Water heaters

Bock Water heaters Energy Saver 66W-399 Manuel utilisateur

Bock Water heaters

Bock Water heaters OT300-A Manuel de service

Bock Water heaters

Bock Water heaters OT600-A Manuel de service

Manuels Chauffe-eau populaires d'autres marques

Kenmore

Kenmore 153.582400 Manuel utilisateur

Applimo

Applimo Edel AIR Manuel utilisateur

STIEBEL ELTRON

STIEBEL ELTRON Eltronom SHU 5 S Manuel utilisateur

clage

clage E-Mini Series Manuel utilisateur

Toyotomi

Toyotomi Oil Miser OM-180 Manuel utilisateur

Bradford White

Bradford White EF Series Manuel utilisateur

Eccotemp

Eccotemp 40-H Manuel utilisateur

Dimplex

Dimplex ECSd125-580 Mode d’emploi

Dux

Dux 32FCR6N Manuel utilisateur

Toyotomi

Toyotomi Oil Miser OM-148 (Type D) Guide de dépannage

Noritz

Noritz N-132M Manuel d'instructions

TESY

TESY GCV7/4S 10047 Fiche technique

A.O. Smith

A.O. Smith Gphe 50 Manuel utilisateur

Koryo

Koryo KWHZF15Y Manuel utilisateur

Pentair

Pentair PSC-14-4-02 Manuel utilisateur

GE 40M06AAG Instructions de montage

Thermor

Thermor AEROMAX SPLIT 2 Manuel utilisateur

American Hometec

American Hometec AHQ-B03X Manuel utilisateur