BlueSpot 19011 Manuel utilisateur
18 PCE POLISHING KIT
User Manual
19011
Contact Us:
Find out more about the BlueSpot® Lifetime Guarantee at www.BlueSpot.uk.com
Orme Business Centre, Greenacres Road, Oldham, OL4 3NT
01
Thank you for purchasing a BlueSpot product, you can find further information
on our range at www.BlueSpot.uk.com. Please ensure that you are using the
product correctly and that all guidance and cautions are followed in accordance
with the instructions. Please retain these instructions for future reference.
General Information
Please make sure that you read these instructions carefully in order to avoid injury when
using the polishing kit. Follow all health and safety rules and regulations. If in doubt and
available please contact a more knowledgeable source.
DO NOT use if damaged.
• If the kit is damaged do not use as this may cause damage to property or cause injury.
• Maintain the kit in good and clean condition for best and safest performance.
• ALWAYS wear protective clothing which includes safety goggles, face shield, dust mask
and gloves when working with this kit.
• Maintain correct balance and footing. Ensure the floor is not slippery and wear
non-slip shoes.
• Keep the work area clean, uncluttered and ensure there is adequate lighting. Ensure that
your work surface has been properly assessed for any potential hazards before
starting work.
• It is advised to mask up any areas that need protection such as table tops and chairs.
• Keep children and unauthorised persons away from the work area.
Safe use
The BlueSpot 18 Piece Polishing Kit includes large high quality buffing wheels, polishing
buffs, woollen mounted points and 6 bars of polishing compound.
The polishing kit is manufactured to give a smooth clean polish on a variety of materials.The
kit is used to reduce dirt and scratches on a painted surface. Once the surface is cleaned and
prepared a polish with this kit will restore the original shine.
The polishing kit works similar to a sanding kit which makes the surface smoother and
reduces the depth of the finish to the deepest scratch leaving it spotless.
A variety of compounds are provided in this kit ranging from coarse for very damaged
surfaces to fine polishes for delicate work. The set also includes many different tools for
different types of materials that are identified in the grid provided.
All buffing wheels and felt bobs are mounted on ¼” shanks that fit most common drill types.
Product Introduction
02
Contents
Instructions (continued)
1. Analyse the surface for any scratches or imperfections that can be identified by touch or
easily by sight.These need to be removed with sanding paper before any work can be
done.
2. After the surface is clean, dry and sanded, select your chosen buffing tool and insert it
into an electric drill or bench grinder (maximum 3000rpm).
3 PCE Buffing wheels: 50mm, 75mm & 100mm
4 PCE Polishing buffs: 50mm & 75mm
5 PCE Woollen mounted points: ball, cone, tapered round, round & bullet
6 PCE Polishing compound: green stainless, white diamond, brown tripoli,
black emergy, red rouge, blue.
03
Instructions (continued)
Disposal
Always check and adhere to national regulations when disposing of any tools that are no
longer functional and cannot be repaired.
• Do not dispose of power tools with household waste.
• Contact your local waste disposal authority for information on how to correctly dispose
of power tools.
3. Refer to the chart and select your chosen material with the polishing compound, starting
from the coarsest.
4. Coat the buff by lightly spinning it into the chosen compound, use it sparingly as only a
small amount is needed for excellent results.
5. Apply the coated buff to the surface to be polished without exceeding 3000rpm as this
will cause the compound to be ineffective.
6. Maintain a constant light pressure whilst leaving the compound and buff to do the work.
7. Continue polishing and applying more compound as required.
8.To remove the compounds after use, apply the drill and buff against a sharp metal edge
to remove any residue.
9. For the best results, use a different buff for each of the compounds to ensure no left
over residue is accidentally applied.
10. Repeat the process with the next finer compound in the chart shown.
11. Continue until the surface appears shiny with no visible marks.
12. Apply the finished compound to the loose single stitched buff and apply light pressure
to finish the job.
13. Wash the polished areas with warm soapy water to remove any leftover residue and
wipe clean with a cloth for a perfect shine.
Notes
ContactDistance to Spot Size
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and
packaging should be sorted, taken to a recycling centre and disposed of in a manner which is
compatible with the environment. When the product becomes completely unserviceable
and requires disposal, drain any fluids (if applicable) into approved containers and
dispose of the product and fluids according to local regulations.
Environmental Protection
Table des matières
