BlueBox Eight1080 Manuel utilisateur
BlueBox Video Wall Controller Series -
BB-VW
User Manual
Contact
BlueBox Video Ltd,
Pontefract Road,
Unit 5 Courtyard 31,
Normanton,
WF6 1JU,
United Kingdom.
Tel: +44 7307 052693
www.bluebox.video
Version 31/03/2020
Video Wall Controller Series User Manual
Copyright © 2020
Preface
Throughout the remainder of this document the product titles Eight1080, Nine1080 and Six4K will
be identified as the “appliance”. Please see product quick start guide for installation and basic setup
guidance.
Copyright
BlueBox Video Limited claims copyright on this documentation. This publication, including all
images, drawings and software, is protected under international copyright laws, with all rights
reserved. No part of this manual may be reproduced, copied, translated or transmitted in any form
or by any means without the prior written consent from BlueBox Video Limited.
Disclaimer
Whilst every effort is made to ensure that the information contained in this manual is correct,
BlueBox Video Limited make no representations or warranties with respect to the contents thereof,
and do not accept liability for any errors or omissions. BlueBox Video Limited reserves the right to
change specification without prior notice, it does not represent commitment from BlueBox Video
Limited and cannot assume responsibility for the use made of the information supplied.
The information in this publication is provided “as is” without warranty of any kind. The entire risk
arising out of the use of this information remains with the recipient.
BlueBox Video shall not be liable for direct, indirect, special, punitive, incidental, consequential or
other damages (including without limitation, damages for loss of business profits, business
interruption or loss of business information) arising out of the use of any product, nor for any
infringements upon the rights of third parties, which may result from such use.
Acknowledgement
All registered trademarks used within this documentation are acknowledged by BlueBox Video
Limited.
Video Wall Controller Series User Manual Page 2
Copyright © 2020
Declaration of Conformity
This section provides the FCC compliance statement for Class A devices and describes how to keep
the system CE compliant.
For EMC compliance, good quality shielded cables or adapters should be used for connection from
the appliance to the display device.
FCC
This appliance complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference
2. This device must accept any interference received, including interference that may cause
undesired operation.
This equipment has been tested and verified to comply with the limits for a Class A digital device,
pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. Operation of this
equipment in a residential area (domestic environment) is likely to cause harmful interference, in
which case the user will be required to correct the interference (take adequate measures) at their
own expense.
CE
The product(s) described in this manual comply with all applicable European Union (CE) directives if
it has a CE marking. Maintaining CE compliance also requires correct cable and cabling techniques.
Directives applied to this product are:
●Low Voltage Directive – 2014/35/EU
●EMC Directive – 2014/30/EU
●RoHS – Restriction of Hazardous Substances Directive – 2011/65/EU
●Waste Electrical and Electronic Equipment Directive – 2012/19/EU
WEEE Disposal
At the end of life all appliances products should be disposed of as per local laws and regulations
dictate. Please contact your local distributor to arrange disposal if in doubt. Our WEEE registration
number is WEE/AX3802YC.
Video Wall Controller Series User Manual Page 3
Copyright © 2020
Warranty and RMA
Warranty Period
Products will be free from defects in material and workmanship for 3 years, beginning on the date of
purchase invoice.
Return Merchandise Authorization (RMA)
Customers must collect and detail all the information about the problems encountered and note
anything abnormal or, print out any on-screen messages, and describe the problems to our repair
team via email.
Customers may be required to return faulty products with or without accessories (manuals, cable,
etc.). If the accessories were suspected as part of the problems, please note clearly which
components are included. Otherwise, the RMA process is not responsible for the devices/parts.
Customers are responsible for the safe packaging of defective products, making sure it is durable
enough to be resistant against further damage and deterioration during transportation. In case of
damages occurred during transportation, the repair is treated as “Out of Warranty.” We always
recommend shipping the product using the original packaging (As it arrived to you).
If the returned item's fault is diagnosed to be from user error or mistreatment, repairs will be treated
as “Out of Warranty”.
Any products returned after the RMA process to other locations besides the customers’ site will
bear an extra charge and will be billed to the customer.
Repair Service Charges for Out-of-Warranty Products
The RMA process will charge for out-of-warranty products in two categories, one is basic
diagnostic fee and another is component (product) fee.
System Level
Component fee: The RMA process will only charge for main components such as CPUs, GPUS,
Memory, Hard Drives etc.
Items will be replaced if the original component cannot be repaired. Ex: motherboard, power
supply, etc.
Board Level
Component fee: The RMA process will charge for main components, such as ICs etc.
Passive components will be repaired free of charge, example: resistors, capacitors.
If RMA goods cannot be repaired, items and components will be returned to the customer without
charge.
Video Wall Controller Series User Manual Page 5
Copyright © 2020
Safety Precautions
WARNING: Read these instructions carefully! Follow all warnings and instructions specified within
this document and/or on the equipment. All cautions should be noted.
CAUTION: The unit will be powered on upon connecting a valid power supply source. Please make
sure to properly shut-down the device’s operating system prior to removing power.
1. Keep this User Manual for later reference.
2. WARNING: Appliance MUST be EARTHED. The appliance uses a three-wire earthed power
system, the input power connector which is equipped with a third pin, is to earth the unit and
prevent electric shock. Do not defeat the purpose of this pin. You must use a 3 pin IEC C13
power cable. If your outlet does not support this kind of plug, contact your service person to
replace your obsolete outlet and install the appliance safely.
3. Disconnect this equipment from any AC outlet before cleaning. Use a soft damp cloth. Do not
use liquid or spray detergents for cleaning. Ensure dry before turning on.
4. Keep this equipment away from liquids. Never pour any liquid into an opening. This may cause
fire or electrical shock.
5. For plug-in equipment, the power outlet socket must be located near the equipment and must
be easily accessible.
6. Put this equipment on a stable surface during installation. Dropping it or letting it fall may cause
damage.
7. The openings on the enclosure are for air convection to protect the equipment from
overheating. DO NOT COVER OPENINGS.
8. Ensure voltage of the power source is correct before connecting the equipment to the power
outlet.
9. Place the power cord in a way so that people will not step on it. Do not place anything on top
of the power cord. Use a power cord that has been approved for use with the product and that
it matches the voltage and current marked on the product’s electrical range label. The voltage
and current rating of the cord must be greater than the voltage and current rating marked on
the product.
10. All cautions and warnings on the equipment should be noted.
11. If the equipment is not used for a long time, disconnect it from the power source to avoid
damage by transient overvoltage.
12. WARNING: Never open the equipment. For safety reasons, the equipment should be opened
only by qualified service personnel. NOTE: Opening the equipment case will void the warranty.
13. If one of the following situations arises, get the equipment checked by service personnel:
a. The power cord or plug is damaged.
b. Liquid has penetrated into the equipment.
Video Wall Controller Series User Manual Page 6
Copyright © 2020
c. The equipment has been exposed to moisture.
d. The equipment does not work correctly, or you cannot get it to work according to the user
manual.
e. The equipment has been dropped and damaged.
f. The equipment has obvious signs of breakage i.e. Rattling sounds
14. Do not place heavy objects on the equipment.
15. The appliance should be installed by qualified personnel only (persons having the appropriate
technical training and experience necessary for product installation).
16. The unit is always recommended to be installed in a rack cabinet, with a supporting rack shelf
below is possible. The unit is always recommended to be installed in a rack cabinet, with a
supporting rails below if possible. The unit should be secured to the cabinet using the 2
mounting tabs.
17. Ensure the unit is installed securely to avoid the unit being dropped or falling from height
accidentally. Dropping it or letting it fall may cause damage.
18. When installing the equipment, please make sure that cables are installed so that accidents
cannot occur. Cables connected to the equipment must not be subject to any mechanical
strain.
CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED. REPLACE ONLY
WITH THE SAME OR EQUIVALENT TYPE RECOMMENDED BY THE MANUFACTURER. DISCARD
USED BATTERIES ACCORDING TO THE MANUFACTURER’S INSTRUCTIONS.
Video Wall Controller Series User Manual Page 7
Copyright © 2020
Hardware
What’s included in the box:
●Appliance
Optional Extras (Depending on Specific Model):
●Mouse/Keyboard
●Optical Cables
●Active DP to HDMI Adapters
Required:
●A common IEC C13 cable is required to power the appliance, this is not provided and the
customer will be required to purchase one of the appropriate length and region for
installation.
This cable must be a 3 wire earthed cable and must be connected to an earthed outlet
socket.
Note: When unpacking, inspect the shipment box and appliance to identify any possible damages
due to shipping. Make sure all items have been delivered and that no items are missing. Contact
your representative should you find any damages or defects.
Note: The product serial number is on the product label, this number helps the support team
identify your device. The serial number can also be obtained through the web portal or on an
appliance built-in display, if supported by your device.
Video Wall Controller Series User Manual Page 8
Copyright © 2020
Product Introduction
Overview
The appliance platform provides a high definition, compact video wall with recording options for
command and control surveillance environments. Equipped with up to 9 1080p/4k outputs,
simplifying traditional video wall systems by reducing footprint to a powerful, single condensed 2U
appliance. Combined CPU and GPU technologies present users with a generic hardware platform for
choice of application. The appliance allows video to be received over the network or locally from
disk. Users can action the latest graphics technologies to provide an unrestricted video layout design
under a familiar Windows platform.
An appliance is optionally supplied with the latest Windows 10 operating system installed and
configured. Interfaces including DirectX and OpenGL allow user applications to leverage hardware
acceleration technology found within the appliances latest generation GPU processor. See appliance
model data sheet for further details
The appliance is a custom industrial hardware platform sourced from long life embedded
components. The customised unit provides a resistant enclosure for physical durability, cooling and
system reliability.
Video Wall Controller Series User Manual Page 9
Copyright © 2020
Hardware Specifications
Appliance
Eight1080
Nine1080
Six4K
Product Codes
BB-VW-8FHD
BB-VW-9FHD
BB-VW-6UHD
Platform
Modular Embedded Motherboard
Modular Embedded
Motherboard
Modular Embedded Motherboard
Processor
7th Gen Intel
7th Gen Intel
7th Gen Intel
Graphics
Intel
Intel
NVidia
Memory
2 x 4GB Dual DDR4, upgrade
options available (Up to 32GB,
2133MHz, 1.2V)
2 x 4GB Dual DDR4, upgrade
options available (Up to 32GB,
2133MHz, 1.2V)
2 x 4GB Dual DDR4, upgrade
options available (Up to 32GB,
2133MHz, 1.2V)
I/O Interface
-Front
1 x Power Switch with LED (Blue)
2 x USB 3.0
1 x Power Switch with LED (Blue)
2 x USB 3.0
1 x Power Switch with LED (Blue)
2 x USB 3.0
I/O Interface
-Rear
2 x USB 2.0
2 x Gigabit RJ45
8 x DisplayPort 1.2 outputs
1 x AC power inlet
2 x USB 2.0
2 x Gigabit RJ45
8 x DisplayPort 1.2 outputs
1 x AC power inlet
2 x USB 2.0
2 x Gigabit RJ45
8 x DisplayPort 1.2 outputs
1 x AC power inlet
Storage
Up to 2 x SATA 2.5” HDD/SDD for
RAID Configuration
Up to 2 x SATA 2.5” HDD/SDD
for RAID Configuration
Up to 2 x SATA 2.5” HDD/SDD for
RAID Configuration
Dimensions
444mm (W) x 221mm (D) x 88mm
(H)
444mm (W) x 221mm (D) x
88mm (H)
444mm (W) x 221mm (D) x 88mm
(H)
Form Factor
2U Rack Mount
2U Rack Mount
2U Rack Mount
Weight
2.5Kg
2.5Kg
2.5Kg
Power Supply
1 x Internal Power supply
Input: 90VAC-240VAC 50/60Hz
180W Typical
250W Max
1 x Internal Power supply
Input: 90VAC-240VAC 50/60Hz
180W Typical
250W Max
1 x Internal Power supply
Input: 90VAC-240VAC 50/60Hz
180W Typical
250W Max
Environment
Operating temperature: 0°C to
40°C
Storage temperature: -40°C to
80°C
Humidity: 10 to 95%
(non-condensing)
Operating temperature: 0°C to
40°C
Storage temperature: -40°C to
80°C
Humidity: 10 to 95%
(non-condensing)
Operating temperature: 0°C to
40°C
Storage temperature: -40°C to
80°C
Humidity: 10 to 95%
(non-condensing)
Compliance
CE approval
FCC Class A
CE approval
FCC Class A
CE approval
FCC Class A
Video Wall Controller Series User Manual Page 10
Copyright © 2020
Ce manuel convient aux modèles suivants
5
Table des matières
