Blue Ridge BOLBF Mode d’emploi

506792-01B Page 1 of 6Issue 1216

Congratulaons...

...you have one of the most modern oil furnaces made.

Your unit has been carefully selected to keep you warm and

comfortable during the winter months. It will deliver superb

performance with only minimal help from you.

To keep your operating costs low and to eliminate

unnecessary service calls, we have provided a few

guidelines to help you with your furnace. These guidelines

will help you understand how your furnace operates and how

to maintain it so you can get years of safe and dependable

service.

For your safety – read before operating

This appliance is equipped with an ignition device which

automatically lights the burner. Do not try to light the

burner by hand.

Do not use this appliance if any part has been under water.

Immediately call a qualied service technician to inspect the

appliance and to replace any part of the control system and

oil control which has been under water.

Periodic Inspections

Your oil furnace is designed to give many years of efcient,

satisfactory service. However, the varied air pollutants

commonly found in most areas can affect longevity and

safety. Chemicals contained in everyday household items

such as laundry detergents, cleaning sprays, hair sprays,

deodorizers, and other products which produce airborne

residuals may have an adverse affect upon the metals used

to construct your furnace.

It is important that you visually inspect the conditions of

the burner and vent from the furnace. A ashlight will be

useful for these inspections. Make one inspection prior to

the beginning of the heating season and another during the

middle. Should you observe unusual amounts of rust, akes

or other deposits, coatings, or corrosion, it is important that

you call your authorized dealer at once to obtain a qualied

service inspection. Even if no unusual rust or other deposits

are observed, it is recommended that the furnace be

inspected and serviced at least once per year by a

qualied service technician.

USER’S INFORMATION MANUAL

BOLBF, BOLBR, BOLHF, BOLHR, BOLUF

Oil-Fired Furnaces

Save these instructions for future reference

If the information in this manual is not followed exactly, a re or explosion may result causing property

damage, personal injury, or loss of life. For assistance or additional information, consult a qualied

installer or service agency.

WARNING

Do not store combustible materials, including gasoline

and other flammable vapors and liquids, near the

furnace, vent pipe, or warm air ducts. The furnace area

must not be used as a broom closet or for any other

storage purposes. Such uses may result in actions that

could cause property damage, personal injury, or death.

WARNING

Never burn garbage or paper in the heating system

and never leave rags, paper, or any ammable items

around the unit.

CAUTION

Installaon and service must be performed by a qualied

installer or service agency.

CAUTION

TABLE OF CONTENTS

PERIODIC INSPECTIONS.............................................1

OPERATING YOUR FURNACE ....................................2

Lighting Instructions .........................................2

Temperature Control ........................................2

Fan Operation ..................................................2

MAINTENANCE OF YOUR FURNACE.........................2

Cleaning/Replacing Filters ...............................2

Combustion/Ventilation Air ...............................4

Venting and Furnace Support ..........................4

WARRANTY...................................................................5

Manufactured By

Blue Summit LLC

8201 C National Turnpike

Louisville, KY 40214

(P) 506792-01B

*P506792-01B*

Page 2 of 6 Issue 1216 506792-01B

Thermostat Operation (when you have heating only)

The thermostat is the only control you’ll need to set, as the

furnace is completely automatic. Just set the temperature

to the desired comfort level.

Thermostat Operation (when you have heating and

cooling)

There are two switches located on the thermostat. One

switch controls the heating and cooling functions. The other

switch is for “FAN” operation, either continuous or automatic.

On the thermostat is the temperature range for the heating

temperature and the cooling temperature desired.

To put the system into operation, push the switch to either

“HEAT” or “COOL” position.

After you have chosen the type of operation you desire,

move the thermostat dial or lever to select the temperature

you would like the system to maintain.

Fan Operation

You may wish to increase your comfort by setting your

system for continuous air circulation of the indoor air. The

fan switch on the thermostat permits you to do this (see

Figure 1).

With the switch in the “ON” position the fan will operate

continuously. “AUTO” position gives fan operation only when

the unit is in either heating or cooling.

Maintenance Of Your Furnace

There are routine maintenance steps you should take to

keep your unit operating efciently. This will assure longer

life, lower operating costs, and fewer service calls. The

steps given in this publication are easy to follow and are

not time consuming. Certain service and maintenance

procedures require the skill of a trained service person who

has specialized tools and training for their use. Please call

your dealer for service. Personal injury can result if you are

not qualied to do this work.

Cleaning/Replacing the Filter

It is very important to clean or replace the air lter regularly.

A dirty air lter can sharply increase the operational costs

of your unit...in some cases it can double the cost. The air

lter should be inspected at least every 6 weeks and

cleaned or replaced as required.

Operating Your Furnace

Lighting Instructions

1. STOP! Read the previous safety information.

2. Set the thermostat to the lowest setting. Turn off electric

power to the appliance.

3. This appliance is equipped with an ignition device. Do

not try to light the burner by hand.

4. Check the oil supply valve.

5. Turn on electric power to the appliance.

6. Set the thermostat to the desired setting.

7. The burner should light and the system should be

controlled by the thermostat. If the appliance will not

operate, call your service technician.

What to do if your unit is not heating properly

If your unit is operating but fails to provide complete comfort,

check the following before calling for service:

1. Be sure the thermostat setting is correct.

2. Check to see if the lter is clean.

3. Be sure air can circulate freely throughout your home.

Do not block supply registers or return grilles with

furniture or rugs.

And if you also have cooling...

4. Keep surface of the outdoor coil free from dirt, lint, paper,

or leaves.

5. Check and clean indoor coil if necessary. (This check

should be made at the start of each cooling season by

your service technician.)

What to do if your unit fails to operate

1. Be sure the main switch that supplies power to the unit

is in the “ON” position.

2. Replace any burned-out fuses or reset circuit breakers.

3. Be sure the thermostat is properly set.

4. If the unit still does not start, call your service technician.

Temperature Control

There are many types and styles of thermostats. Yours may

look different from the one pictured in Figure 1, depending

on the type of thermostat and whether cooling was installed

with the system. However, almost all thermostats perform

the same basic functions described in the following section.

Always turn off the power to your furnace before

removing the doors or lters. Failure to turn the power

off could result in property damage, personal injury, or

death.

WARNING

Thermostat

Figure 1

506792-01B Page 3 of 6Issue 1216

Upow Units

To replace the lter in an upow unit, refer to the following

directions and Figure 2.

Side Return

To replace the lter in a furnace with an external lter rack

or cabinet on either side of the furnace cabinet:

1. Turn off the power to unit.

2. The lter(s) may be removed by sliding toward the front.

Replace in a reverse procedure.

Bottom Return

To replace the lter in a furnace with a bottom return air:

1. Turn off the power to unit.

2. Remove lower front panel by lifting up and pulling out.

3. The lter(s) may be removed by sliding toward the front.

Replace in a reverse procedure.

Basement Units

To replace the lter in a basement unit (see Figure 3):

1. Turn off power to unit.

2. Remove lower rear panel by lifting up and pulling out.

3. The lter(s) may be removed by sliding out through the

rear of the furnace. To reinsert, place lter on the two

lter supports and slide into unit.

Restore power to the furnace after the door or panel has

been replaced and check furnace for proper operation. If

the unit does not operate, call your dealer for service.

Lubrication

Lubrication of the bearings in the circulating air blower motor

and the combustion blower motor is not recommended.

Side Return Bottom Return

R/A

Duct

Fi lter Rack

Filter

(slides in from front of unit)

Filter Base

Side

Panel

Front

Panel

Upow Units: Filter Replacement

Figure 2

Filter Rear

Furnace

Filter

Supports

Basement Units: Filter Replacement

Figure 3

The unit may contain either a disposable lter or a permanent

lter. The type of lter may be indicated on a label attached

to the lter. If a disposable lter is provided, replace with the

same type and size as the original lter. If a permanent lter

is provided, clean lter and place back in furnace. To clean

a permanent lter, shake lter to remove excess dirt and/

or use a vacuum cleaner. Wash lter in soap or detergent

water and replace after lter is dry.

If your air distribution system has a central return air lter-

grille, you do not need a lter in your furnace. Be sure to

clean the lter-grille as recommended above.

Dirty lters are the most common cause of inadequate

heating or cooling performance. A clogged lter will not

permit adequate airow. This can cause heat exchanger

failure or cooling coil freeze-up along with the accompanying

costly service calls.

The dealer may have changed the filter size, so the

information provided in Table 1 may not apply to your

installation.

Always measure the original lter and replace with the same

size and type.

Table 1

Factory-Supplied Filters

Models BOLHF and BOLHR are not equipped with factory-supplied

lters. The lters for these units are supplied in the eld.

Models Size

BOLUF 16” X 25”

BOLBF, BOLBR (57/72, 84/95) 18” X 19”

BOLBF, BOLBR (112/125) 19” X 21”

BOLBR (140/168) 20-1/8” X 22-7/16

BOLBR (168/196) 24-5/8” X 24-3/8”

Page 4 of 6 Issue 1216 506792-01B

Combustion and Ventilation Air

Adequate air must reach your furnace to provide for proper

and safe operation. Any obstruction of this airow can

cause an unsafe condition which may result in death

or permanent injury. Lethal carbon monoxide gas can

be produced if combustion air is restricted.

Furnaces located in a closet, alcove, or utility room must

have provision for adequate air supply by means of upper

and lower grilles in the door, or by the introduction of outside

air, or both. National codes and local code requirements

are generally alike. However, local codes take precedence.

Venting and Furnace Support

Venting of this furnace must comply with our published

instructions. If the installer has not followed these

requirements, you should request the installer to comply

as soon as possible.

Make sure all ue product materials external to the furnace

are clear and free of any obstruction, slope upward, and

have no holes or leaks.

It is important that the outside area where the vent

terminates is kept clear of any obstructions which might

block or impede the venting of the furnace.

Should any unusual conditions be observed during your

inspections, call your authorized service dealer at once.

Return Air

Check that all return air duct connections are tight and

sealed to the furnace cabinet and that all return air grilles

or registers are located outside the space containing the

furnace.

506792-01B Page 5 of 6Issue 1216

BLUE SUMMIT LLC

EQUIPMENT LIMITED WARRANTY

APPLIES IN U.S.A. AND CANADA ONLY

FAILURE TO MAINTAIN YOUR EQUIPMENT WILL VOID THIS WARRANTY

COVERED EQUIPMENT

The following heating and cooling equipment is covered by the Limited Warranty,

Condensing Units: BA13, BA16

Heat Pumps: BHP15, BHP16LT

Gas Furnaces: BG801UHP, BG801UHE, BG802UHV, BG921UHP, BG951UHP, BG951UHE, BG952UHV, BG961UHE

Oil Furnace: BOL83BF, BOL83BR, BOL83HF, BOL83HR, BOL83UF

Air Handlers: BE5C, BE5E, BE5V

Package Equipment: BPHP14, BPGE14

PARTS and COMPRESSOR COVERAGE

The covered equipment and covered parts and compressor are warranted by Blue Summit for a period of ve (5) years from the date of the original installation, when installed in a residential application (which includes homes,

duplexes, apartments and condominiums). The covered equipment and covered parts are warranted for a period of one (1) year and compressor is warranted for ve (5) years by Blue Summitfrom the date of the original installation,

when installed in non-residential applications. If, during this period, a covered component fails because of a manufacturing defect, Blue Summit will provide a free replacement part to the owner through a licensed service contractor

utilizing an Blue Summit distributor. You must pay shipping charges and all other costs of warranty service. Blue Summit will not pay labor involved in diagnostic calls or in removing, repairing, servicing or replacing parts. Such cost

may be covered by a separate warranty provided by the installer.

HEAT EXCHANGER COVERAGE

All covered heat exchangers are warranted by Blue Summit for a period of twenty (20) years from the date of original installation in a residential application. Heat exchangers in all non-residential applications are warranted for a

period of ten (10) years.

NOTE: In the event that a component covered by this warranty is no longer available, Blue Summit, at its option, through a established Blue Summit distributor, will provide a free suitable substitute component or will allow a credit

toward the purchase of an equivalent new Blue Summit product (at the current suggested distributor’s cost).

If the date of original installation cannot be veried, the warranty period will be deemed to begin six (6) months after the date of manufacture.

EXCLUDED COMPONENTS

The following components are not covered by this warranty: cabinets, cabinet pieces, air lters, driers, refrigerant, refrigerant line sets, belts, wiring, fuses, oil nozzles, unit accessories and any parts not affecting unit operation.

CARE OF EQUIPMENT

Your new Blue Summit unit must be properly installed, operated and maintained in accordance with the unit installation, operation and maintenance instructions provided with each Blue Summit unit. Failure to provide maintenance

per Blue Summit instructions will void this warranty.

WARRANTY PROCEDURE

When service or warranty parts are required:

1. Call your local licensed service dealer or contractor

2. If the installing dealer is unable to provide warranty service, check online at www.alpinehomeair.com.

3. Be prepared to furnish the following information:

a. Complete model and serial number

b. Proof of required periodic maintenance, installation date and location.

c. An accurate description of the problem

WARRANTY LIMITATIONS

1. All installation must be in compliance with applicable laws, regulations, codes, and ordinances.

2. Products purchased over the internet or through other electronic means must be installed by a qualied installer and the installation must adhere to the Quality Installation protocols of the Air Conditioning Contractors of

America (ACCA), and these products must be registered with the manufacturer within 60 days of installation for the warranty to be in place.

3. This warranty is void if the covered equipment is removed from the original installation site.

4. This warranty does not cover damage or defect resulting from:

a. Flood, wind, re, lightning, mold, or installation and operation in a corrosive atmosphere, or otherwise in contact with corrosive materials (chlorine, uorine, salt, recycled waste water, urine, fertilizers, or other

damaging substances or chemicals). Accident, or neglect or unreasonable use or operation of the equipment including operation of electrical equipment at voltages other than the range specied on the unit

nameplate (includes damages caused by brownouts).

b. Modication, change or alteration of the equipment, except as directed in writing by Blue Summit.

c. Operation with system components (indoor unit, outdoor unit and refrigerant control devices) which are not an AHRI match or meet the specications recommended by Blue Summit.

d. Operation of furnaces with return air temperatures of less than 60ºF (16ºC) or operation of a furnace eld installed downstream from a cooling coil.

e. Use of contaminated or refrigerant not compatible with the unit.

The installation of replacement parts under the terms of this warranty does not extend the original warranty period.

Blue Summit makes no express warranties other than the warranty specied above. All implied warranties, including the implied warranties of merchantability and tness for a particular purpose, are excluded to the extent to a

period legally permissible. Should such exclusion or limitation of the warranty be unenforceable, such implied warranties are in any event limited to a period of one (1) year. Liability for incidental and consequential damages is

excluded. Some states do not allow limitation of incidental damages, so the limitations or exclusions may not apply to you. Blue Summit will not pay electricity or fuel costs, or increases in electricity or fuel costs, for any reason

whatsoever, including additional or unusual use of supplemental electric heat. This warranty does not cover lodging expenses or labor charges.

Blue Summit shall not be liable for any default or delay in performance under this warranty caused by any contingency beyond its control.

This warranty gives you specic legal rights, and you may also have other rights which vary from state to state.

NOTE TO CUSTOMER

Please complete information below and retain this warranty for your records and future reference.

Outside Unit Model Number: _______________________________________________ Serial Number: _______________________________ Installed Date: _______________

Furnace / Air Handler: ____________________________________________________ Serial Number: _______________________________ Installed Date: _______________

Installing Company Name: ________________________________________________________________________________ Phone: _________________________________

Installing Company Address: ________________________________________________ State/Province: _______________________________ Zip/Postal Code: ____________

8201 C National Turnpike, Louisville KY 40214

(09/22/2017)