Blue Guard BG-One Manuel utilisateur

PRODUCT DESCRIPTION

The BG-One is an electronic oil and fuel detector with smart bilge pump switch that uses patented technology to detect the presence of oil or fuel and

integrates with the bilge pump system. Pump power is controlled by the BG-One. If oil or fuel is detected, the BG-One will prevent pumping the oil out

of the bilge by turning the pump power OFF. If water or other liquid is detected, the pump will be turned ON. The BG-One is CE and ISO 8846 Marine

Ignion Protecon Cered, tested to ABYC-1500 standards.

There are three modes that are available in the BG-One which are congured using the BGI Cong App, which can be downloaded from the App Store or

Google Play. The App is used on a mobile device with Bluetooth to wirelessly connect to the BG-One device. The App allows selecon of the operang

mode and will report the input voltage level, system temperature alarm state, and pump switch state. The BGI Cong App also allows changing the name of

the device for easy idencaon. The App can only congure the device in the rst minute that it is powered up.

INSTALLATION

The BG-One is designed for mounng near the bilge pump in a vessel.

It should be mounted approximately 2” above the bilge pump outlet as

shown in the Blue Guard Installaon Guide. A mounng bracket and three

#8x0.75” 316 stainless steel screws are provided to allow mounng to a

vercal or horizontal structure.

If the device is mounted on the boom of the hull of the vessel the

strainer should be mounted rst and then the main unit aached.

The Blue Guard Installaon Guide shows the wiring for all supported

conguraons. All wiring connecons are made using heavy-duty 14

gauge marine grade wire. All wiring should be done by a licensed

electrician following NEC code.

INSTALL STEPS:

1) Locate proper mounng locaon for the BG-One, near the bilge pump

and approximately 2” above the pump outlet.

2) Install mounng bracket to bulkhead using two #8x0.75” 316 stainless

steel screws provided*.

3) Aach the BG-One into bracket with product label facing up, and wiring

close to bracket.

4) Run wiring to BG-JBox, BG-CP, bilge pump, and baery depending on

the installaon chosen from the Blue Guard Installaon Guide. Secure

the wiring. It is recommended that connecons to the BG-JBox be

made using 14 AWG crimp spade lugs at the ends of the wires.

5) Apply power to the system.

6) Connect to the BG-One using the BGI Cong App, set the Mode if not

using Mode A (Marina). The App can be used to view the system

parameters at any me, but the user must connect within one minute of

powering on the BG-One device to congure it.

*The BG-One can also be mounted on the hull using three #8x0.75” 316 stainless steel screws.

Mount the strainer rst, then aach the BG-One into place.

SMART SWITCH MODES OF OPERATION

Mode A (Marina)

- Turns pump ON when water is detected

- Turns pump OFF when oil or fuel is detected

- Turns pump back ON when only water is detected

Mode B (Marine Sanctuary)

- Turns pump ON when water is detected

- Turns pump OFF when oil or fuel is detected

- Stays OFF unl alarm and bilge is cleared (Requires power cycling

of device)

Standard Mode (High Seas)

Bilge pump switch only (will turn ON or OFF for any liquid)

Strainer

Detachable Mounng Bracket

BG-One

Smart Bilge Pump Switch with Oil and Fuel Detector

USER MANUAL

BG-One |USER MANUAL |REV A

WIRING DESCRIPTION

Auto Power (Orange Wire) — System Power In (Can be supplied on either the Auto or Manual wire): If power is supplied to the Auto wire, the BG-One

mode of operaon will control the voltage on the Bilge Pump Power (Brown Wire). Supports 12 or 24 Vdc power system.

Manual Power (Red Wire) — System Power In (Can be supplied on either the Auto or Manual wire): If power is supplied to the Manual wire, the BG-One

will energize the Pump Power (Brown Wire). Supports 12 or 24 Vdc power system.

Bilge Pump Power (Brown Wire) — Pump Power Output: Connect to Bilge Pump power. Note: The voltage supplied on this line is the same as the voltage

provided into the BG-One on the Auto or Manual Power line. Max current sourced is 20 amps.

Alarm (Yellow Wire) — Alarm Output: Transions from 0 Vdc to the voltage supplied on the Auto or Manual lines when oil is detected in Mode A (Marina),

Mode B (Marine Sanctuary), and Standard Mode (High Seas). The output supplies up to 1 amp current. Be careful not to connect devices that have a high

inrush current that exceeds 1 amp or permanent damage to the unit may occur.

Ground (Black Wire) — Ground Return: Connect to system ground per Blue Guard Installaon Guide.

MAINTENANCE

Periodically check the base of the unit to ensure that no foreign material is stuck inside the sensor poron of the unit.

If salt has built up on the sensor poron, rinse with fresh water to clean.

When oil is detected in the bilge, the leak should be repaired and the bilge should be cleared of oil as a part of praccing prudent seamanship. Aer the

user of the boat has cleared the bilge of oil, the boom of the BG-One’s sensor should be wiped with a so clean cloth to remove the oil or fuel residue. If

any further cleaning is required, use rubbing alcohol followed by wiping with a so clean cloth.

FCC & IC STATEMENT

Federal Communicaons Commission Statement

You are cauoned that changes or modicaons not expressly approved by the part responsible for

compliance could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operaon is subject to the following two

condions: 1. This device may not cause harmful interference and 2. This device must accept any

interference received, including interference that may cause undesired operaon of the device.

FCC RF Radiaon Exposure Statement

This equipment complies with FCC radiaon exposure limits set forth for an uncontrolled environ-

ment. End users must follow the specic operang instrucons for sasfying RF exposure limits.

This transmier must not be colocated or operang with any other antenna or transmier.

Industry Canada (IC)

This device complies with Industry Canada licence-exempt RSS standards. Operaon is subject to

the following two condions: 1. This device may not cause interference, and 2. This device must

accept any interference, including interference that may cause undesired operaon of the device.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio ex-

empts de licence L’exploitaon est autorisée aux deux condions suivantes: 1. l’appareil ne doit pas

produire de brouillage, et 2. l’ulisateur de l’appareil doit accepter tout brouillage radioélectrique

subi, même si le brouillage est suscepble d’en compromere le fonconnement.

IC RF Radiaon Exposure Statement

To comply with IC RF exposure requirements, this device and its antenna must not be co-located or

operang in conjuncon with any other antenna or transmier.

Pour se conformer aux exigences de conformité RF canadienne l’exposion, cet appareil et son

antenne ne doivent pas étre co-localisés ou fonconnant en conjoncon avec une autre antenne

ou transmeeur.

WARRANTY INFORMATION

Blue Guard Innovaons, LLC 4909 Naulus Ct N, Suite 121 Boulder, Colorado 80301 warrants

to the original consumer purchaser that this product will be free from defects in material and

workmanship, providing that the unit is not opened or otherwise abused for a period of three (3)

years from the date originally purchased unless otherwise noted or sold by the manufacturer. The

exclusive remedy of the consumer purchaser in the event the product is defecve is to return the

product to Blue Guard Innovaons, LLC at the above address, freight prepaid with original sales

receipt. IMPORTANT: FOR THIS WARRANTY TO BE EFFECTIVE, the product MUST BE SUPPLIED

WITH PROOF OF ORIGINAL PURCHASE DATE OF THE PRODUCT. THE ACCEPTANCE BY BLUE

GUARD INNOVATIONS, LLC OF ANY PRODUCT RETURNED SHALL NOT BE DEEMED AN

ADMISSION THAT SUCH PRODUCT IS DEFECTIVE OR IN VIOLATION OF ANY WARRANTY. THE

COMPANY RESERVES THE RIGHT TO REPAIR OR REPLACE THE PRODUCT. NO REPRESEN-

TATIVE OR OTHER PERSON IS AUTHORIZED TO ASSUME FOR BLUE GUARD INNOVATIONS,

LLC ANY ADDITIONAL LIABILITY IN CONNECTION WITH THE SALE OF ITS PRODUCTS OR TO

ALTER THIS WARRANTY IN ANY WAY. IN NO EVENT WILL BLUE GUARD INNOVATIONS, LLC BE

LIABLE FOR MORE THAN THE SALES PRICE OF THE PRODUCT. UNDER NO CIRCUMSTANCES

WILL BLUE GUARD INNOVATIONS, LLC BE LIABLE FOR ANY LOST PROFITS, INCIDENTAL OR

CONSEQUENTIAL COSTS, EXPENSES, OR DAMAGES. THE LIMITATION ON LIABILITY FOR LOST

PROFITS, INCIDENTAL OR CONSEQUENTIAL COST EXPENSES OR DAMAGES SHALL SURVIVE

ANY FAILURE OF ESSENTIAL PURPOSE OF THIS LIMITED WARRANTY. All wiring on the vessel

shall be performed by a QUALIFIED MARINE ELECTRICIAN and in accordance with the “Fire

Protecon Standard for Motor Cra”, NFPA No. 302. The Standards of the American Boat and Yacht

Council, Inc., and the USCG Safety Standards for Boat Electrical Systems (33 CFR 183). Some states

do not allow the exclusive or limitaon of incidental or consequenal damages, so the above limita-

on may not apply to you. NO EXPRESS OR LIMITED WARRANTY, INCLUDING WARRANTY OF

MERCHANTABILITY AND FITNESS SHALL EXTEND FOR ANY PERIOD OF TIME GREATER THAN

THREE (3) YEARS FROM THE DATE OF ORIGINAL PURCHASE OF THIS PRODUCT. Some states

do not allow limitaon on how long an implied warranty lasts, so the above limitaon may not apply

to you. CAUTION - Warranty void if seal on product is broken or product is tampered with in any

way, if any electric cord is cut back more than 4 inches, if electric splices become submerged, or if

product is installed contrary to instrucons or warnings. Blue Guard Innovaons, LLC 4909 Naulus

Ct N, Suite 121 Boulder, Colorado 80301.

OIL DETECTION SENSITIVITY & PUMP RUN TIME

Set low, medium, or high oil detecon sensivity via the BGI Cong App. Set the pump run me aer water and oil detecon via the BGI Cong App.

Set BG-One Switch Pump Run Time*

Aer Water Detecon Event (Normal) — Set pump run me (15-60 seconds). Factory default is 15 seconds.

Aer Oil Detecon Event — Set pump run me aer oil detecon (3-15 seconds). Factory default is 3 seconds.

*Aer water is detected or water is detected for ve seconds aer oil is detected, the pump will be acvated. The pump mer set above will start when the sensor detects air during pump acvaon. As long