Blue Aura WS90t Manuel utilisateur
1
Features:
▪ Multifunction remote control – with Track Fwd/Back/Pause/Play feature.
▪ Range up to 25 meters
▪ No interference or delays – audio latency 18ms (max)
▪ RF Band 2.4GHz/Sample Rate 48KHz
▪ Built in Receiver with Transmitter supplied
▪ Plug & play – no software required
▪ Faux leather covered cabinets with stitching detail
WS90t
2
What's in the box?
?
2 x Power Cable
1 x Transmitter
1 x 3.5 – 3.5 Audio Cable
1 x USB – USB Mini Cable
1 x Optical – 3.5 Cable
1 x USB Adapter
1 x Remote Control
1 x 3.5-RCA Cable
Box A.
Box B.
Box C.
2 x Floor-Stand Speakers
2 x Base
8 x M6 Bolt (Pozi)
8 x Spike
8 x Rubber Ended Spike
8 x Spike Foot
3
WS90t Operating Instructions
Thank you for choosing Blue Aura
The agship product of the Blue Aura Performance Series, WS90t has been developed using the latest advances in wireless
technology, the operating frequency (2.4GHz) is not prone to interference from other wireless devices and the effective
signal range is 25 metres. Both loudspeakers are tted with active ampliers equipped with high quality audio components
aiding delivery of the audio signal. Equipped with two paper cone drive units and a soft dome high frequency unit, the
WS90t delivers a commanding acoustic performance making a statement, both in sound and style.
To gain maximum performance from your WS90t loudspeakers please take time to read this operating guide.
System setup is straight forward, however if you are having any problems please contact us at [email protected] or
visit the Q&A section of our website.
4
This symbol indicates a safety warning
This symbol indicates an advisory warning
Once connected to the mains supply, never attempt to remove drive units or rear amplier panels. Do not use these
loudspeakers if defective and if for any reason they are found to be defective, unplug from the mains supply.
Only use the supplied power cables and USB power adapter and replace immediately if damaged.
Should you have any problems please contact your Blue Aura Distributor.
www.blueaura.co.uk/contacts
The loudspeakers are covered with a soft faux leather material. Please take care when unpacking the speakers to
avoid scratching or indenting the material.
Before installing this product please read all of the instructions.
The amplier inside the loudspeaker have built in thermal and short circuit protection.If an amplier is driven beyond
its power output capabilities it will produce distorted sound which may damage your loudspeakers. Make sure
you do not leave your loudspeakers unattended when playing and reduce the volume at the rst sign of audible
distortion.We recommend that you keep all packing until you are completely satised with your purchase.
The mesh grilles on your WS90t loudspeakers have been designed to provide acoustic clarity and no signicant
sound improvement will be gained by removing them.
5
Getting Started
Tools required
A B C D Ex 8 x 8 x 8 x 8
Unpacking your loudspeakers and attaching the plinth.
WS90t is supplied with a plinth which must be attached to ensure loudspeaker stability.
10KG
Parts supplied
6
Align the screw holes
and fit four M6 pozi
head screws.
To ensure a rigid
and stable fit, secure
screws 1 and 4
followed by 2 and 3
2.
A
12
4
3
EBefore unpacking, ensure a
clean soft but stable surface
is available to place the
loudspeaker on its top to allow
the plinth to be tted.
Carefully remove the
loudspeaker from the carton
and place on its top to allow
access to the base of the
cabinet.
Carefully unpack the plinth
and place on the base of the
cabinet.
1.
Floor
7
ENSURE SPIKES DO NOT PENETRATE CABLES
Fit the desired feet, spikes for carpets
or rubber feet where flooring is to be
protected.
If using Spikes – Insert the spikes and loosely
fit lock nuts. Once upright, ensure the
loudspeaker is stable.
Adjust spikes where necessary to ensure
loudspeaker is level, and then fully tighten
lock nuts.
Spike support cups are available to use
where Spikes are preferred but flooring is
to be protected.
3.
B
D
Why use spikes?
Some low frequency energy is dissipated when a loudspeaker
is placed on a soft surface, i.e. carpets. This effect can be
minimised by using Spikes to help couple the loudspeaker to the
oor.
Spikes help to minimize overall vibration of the loudspeaker by
reducing the amount of sound energy between the loudspeaker
and the oor
8
Loudspeaker placement
Left and Right loudspeakers can be identied by looking at the amplier panel on the rear of each cabinet. Place the
loudspeakers in your preferred position but within reach of wall sockets. With the wall socket in the OFF position connect the
power lead to the loudspeaker using only the supplied power cables. Once connected, the mains switch can be turned to
the ON position.
What is the ideal position for my WS90t loudspeakers?
Placing each WS90t at least 300mm from the back wall will reduce reections and improve accuracy and detail. Each
loudspeaker should be the same distance from where you are seated. Ideally the loudspeakers and the listening position
should form an equilateral triangle. Depending on room layout, some “toeing in” may improve stereo imagery and staging
by reducing reections from side walls.
The listening postion and
the loudspeakers should
form an equilateral triangle.
Depending on room layout,
some "toeing in" may
improve stereo imagery.
9
To use your speakers with a PC or MAC
To use your speakers with other devices (RCA connection)
The transmitter needs to be powered; by using the USB connector on a PC for example, power is provided.
To use the transmitter with equipment that does not have a USB socket the mains adapter is required.
Connect the USB connector from the transmitter to the USB socket on the supplied mains adapter.
Using the “line out” cable provided, plug the red and white plugs (RCA) into your device with line out, e.g. CD player or TV,
connect the other end of the cable (mini jack) to the transmitter.
Plug the adapter into to a convenient wall socket and turn on.
Push the button in the centre of the transmitter to select a free zone.
Using the remote control press the “station” button” to nd the signal from the new source equipment.
Wireless Connection Methods
MAC set-up
1.Insert the USB connector from the
transmitter to a free USB socket on your
MAC.
2.Go to System Preferences and under
Hardware choose Sound.
3.Click Output in Menu and choose USB
headset.
PC set-up
1.Insert the USB connector from the transmitter to a free USB socket on your PC or
laptop.
2.Wait until the software has been installed, usually a conrmation beep or
message window alert.
If the above instructions do not work you may need to do the following.
Click Start button on PC, go to the Control Panel, and choose Sound & Sound
Devices
Under Playback of Audio; Default unit choose USB headset.
If you are still having problems please contact [email protected].
10
To use your speakers with MP3 devices (headphone out)
Plug one end of the supplied 3.5mm mini jack lead into the transmitter and the other end into the headphone socket on your device.
Plug the USB connector from the transmitter into the mains adapter and plug the mains adapter into a convenient wall socket and turn on.
Push the button in the centre of the transmitter to select a free zone.
Using the remote control press the “station” button” to nd the signal from the new source equipment.
Using the Optical Connection
For source devices with optical connections the supplied Optical – 3.5mm plug can be used. Insert the Optical (TOSlink) plug into the
optical socket on your source device and the other end into the 3.5 socket on the transmitter. Plug the USB connector from the transmitter
into the supplied mains adapter and plug the the mains adapter into a convenient wall socket, and turn on. Push the button in the
transmitter to select a free zone. Using the remote control press the STATION button to nd the signal from the new source equipment. The
LED colour on both loudspeakers should be the same as the LED on the transmitter.
….WIRELESS SOUND FROM MULTIPLE DEVICES
By adding more transmitters (optional), the audio network can by separated into 3 house codes allowing multiple devices to be used to
play music through your WS90t speakers.
….ADD MORE WS90t SPEAKERS TO THE AUDIO NETWORK
Limitless numbers of WS90t speakers can be added to your system within wireless range of the transmitter. You can add more speakers to
one room, or add speakers in several rooms.
What are the benets of using the optical cable? Using the Optical connection method provides a pure digital audio signal, no
line loss or ground interference.
Table des matières
Autres manuels Blue Aura Système de haut-parleurs
Manuels Système de haut-parleurs populaires d'autres marques
Sondpex
Sondpex Active Speaker System and Digital Music... Manuel utilisateur
JVC
JVC NX-PN7 Manuel utilisateur
Marshall Amplification
Marshall Amplification AR-DM61-BT Manuel utilisateur
Yamaha
Yamaha NX-A01 - Speaker Sys Manuel utilisateur
SE Audiotechnik
SE Audiotechnik I-LINE Manuel utilisateur
Gemini
Gemini WRX-843 Series Manuel utilisateur