Blodgett BLT-30G Manuel du propriétaire
1
BLT-G
GAS FLOOR MODEL BRAISING PAN WITH
MANUAL TILT
INSTALLATION – OPERATION – MAINTENANCE
BLODGETT OVEN COMPANY
www.blodgett.com
44 Lakeside Avenue, Burlington, Vermont 05401 USA Telephone (800) 331-5842, (802) 860-3700 Fax: (802) 864-0183
S00071 Rev A (5/04)
2
IMPORTANT NOTES FOR INSTALLATION AND OPERATION
It is recommended that this manual be read thoroughly and that all instructions be
followed carefully. This manual should be retained for future reference.
This is the safety alert symbol. It is used to alert you to potential
personal injury hazards. Obey all safety messages that follow this
symbol to avoid possible injury or death.
FOR YOUR SAFETY: Do not store or use gasoline or other
flammable vapors or liquids in the vicinity of this or any other
appliance.
WARNING: Improper installation, operation, adjustment, alteration,
service or maintenance can cause property damage, injury or death.
Read the installation, operating and maintenance instructions
thoroughly before installing, operating or servicing this equipment.
WARNING: Instructions to be followed the event that the operator of
this appliance smells gas must be posted in a prominent location.
This information shall be obtained by consulting the local gas
supplier.
WARNING: In the event you smell gas, shut down equipment at the
main shut off valve and contact the local gas company or gas
supplier for service.
Do not attempt to operate this unit in the event of a power failure.
Keep the appliance area free and clear from combustibles.
NOTICE: Contact the factory, the factory representative or local service company to
perform maintenance and repairs.
Do not obstruct the flow of combustion and ventilation air.
Adequate clearances must be maintained for servicing and proper operation.
3
TABLE OF CONTENTS
DESCRIPTION PAGE
Important Notes for Installation and Operation ............................................................... 2
Service Connections ....................................................................................................... 4
1.0 Installation Instructions ............................................................................................. 5
2.0 Operating Instructions .............................................................................................. 9
3.0 Cooking Guidelines ............................................................................................... 11
4.0 Cleaning ................................................................................................................15
5.0 Maintenance ........................................................................................................... 15
6.0 Troubleshooting ..................................................................................................... 16
4
SERVICE CONNECTIONS
SUPPLY PIPE PRESSURE (W.C.)
BLT-40G
BLT-30G
MODEL
kW/HR.BTU/HR.
11"-14" (279-356mm)7"-14" (178-356mm)
29.3
23.4
100,000
80,000
GAS SUPPLY
Natural Propane
DIMENSIONS
10.5
267
10.5
267
74.25
1886
37.25
946
43.13
1095
51.75
1314
24
610
24
610
33.5
851
43.5
1105
988
38.88
959
37.25
A
49.5
1257
58.5
1486mm
inches
mm
inches
CAPACITYMODEL
30 gallons
114 litres
40 gallons
152 litres
BLT-30G
BLT-40G 100,000
80,000
BTU
37.25
946
BCDEFGHUNITS
1886
74.25
4.75 [121]
3.25 [83]
C
A
2.12 [54]
B
9.75 [248]
D
22 [559]
40.25 [1022]
39.25 [997]
SHOWN WITH OPTIONAL FAUCET
POUR PATH 21 [533]
G9.38 [238]
22 [559]
12 [305]
H
36 [914]
17 [432]
20.75 [527]
F
E
REAR FLANGED FOOT DETAIL
4
7/16" [11mm] HOLES
ON 3 [76] B.C.
EQUALLY SPACED
Ø
DIMENSIONS ARE IN INCHES [MM]
Supply gas through 1/2" pipe . A gas shut-off valve must be installed in supply piping convenient and adjacent to appliance.
Electrical Connection, unless otherwise specified 120 Volts, 60 Hz, 1 PH. furnished with 3 prong plug and cord. Less than 2 amperes.
5
1.0 INSTALLATION INSTRUCTIONS
INSTALLATION CODES AND STANDARDS
Installation must conform with local codes, or in the absence of local codes, with the
National Fuel Gas Code, ANSI Z223.1/NFPA 54, or the Natural Gas and Propane
Installation Code, CSA B149.1, as applicable.
1. The appliance and its individual shut off valve must be disconnected from the gas supply
piping system during any pressure testing of that system at pressures in excess of ½ psi
(3.5 kPa).
2. The appliance must be isolated from the gas supply piping system by closing its individual
manual shut off valve during any pressure testing of the gas supply piping system at test
pressures equal to or less than ½ psi (3.5 kPa).
Electrical grounding must be provided in accordance with local codes, or in the absence of
local codes, with the National Electrical Code, ANSI/NFPA 70, or the Canadian Electrical
Code, CSA C22.2, as applicable.
FLUE CONNECTIONS
Do not obstruct the flow of flue gases from the flue duct located on the rear of the gas
fired tilting skillet. It is recommended that the flue gases be ventilated to the outside of
the building through a ventilation system installed by qualified personnel.
Information on the construction and installation of ventilating hoods may be obtained
from the standard for “Vapor Removal from Cooking Equipment”, NFPA No. 96 (latest
edition), available from the National Fire Protection Association, Batterymarch Park,
Quincy, MA, U.S.A. 02269.
UNPACKING
Immediately after unpacking, check for possible shipping damage. If the gas fired tilting
skillet is found to be damaged, save the packaging material and contact the carrier
within 15 days of delivery.
Before installing, verify that the type of gas supply (natural or propane) and electrical
service agree with the specifications on the rating plate located on the left side console
as you face the front of the appliance. If the supply and equipment requirements do not
agree, contact your dealer immediately.
6
1.0 INSTALLATION INSTRUCTIONS (Continued)
LOCATION
The equipment must be kept free and clear of combustible substances. The appliance,
when installed, must have minimum clearance from combustible and non-combustible
construction of 0" from sides and 6" (152 mm) from the rear. The appliance is intended
for use on non-combustible floors.
The installation location must allow adequate clearances for servicing and proper
operation. A minimum front clearance of 36" (914 mm) is required.
The appliance must be installed so that the flow of combustion and ventilation air will not
be obstructed. Adequate clearance for air openings into the combustion chamber must
be provided. Make sure there is an adequate supply of air in the room suitable for the
amount of combustion gas feeding the burners.
Do not permit fans to blow directly at the appliance, and wherever possible, avoid open
windows next to the appliance. Avoid wall-type fans which create air cross currents
within the room.
LEVELING AND ANCHORING (For appliances not equipped with casters)
1. Set the appliance in place and level left to right and front-to-back using spirit level.
2. Mark hole locations on floor through anchoring holes provided in flanged adjustable
feet.
3. Remove appliance and drill holes in locations marked on floor and insert proper
anchoring devices (not supplied).
4. Set unit back in position and re-level left to right and front to back.
5. Bolt and anchor appliance securely to the floor.
6. Seal bolts and flanged feet with silastic or equivalent compound.
7
1.0 INSTALLATION INSTRUCTIONS (Continued)
GAS CONNECTIONS
All gas supply connections and any pipe joint compound used must be resistant to the
action of propane gases.
The gas inlet is located under the left hand control console.
Connect gas supply to the appliance. The gas supply line must be at least the
equivalent of 3/4" iron pipe with an incoming pressure of 7" - 14" W.C. (Water Column)
for natural gas or 11" - 14" W.C. (Water Column) for propane gas. Make sure the pipes
are clean and free of obstructions, dirt and piping compound.
Codes require that a gas shutoff valve be installed in the gas line ahead of the tilting
braising pan.
Natural gas and propane gas skillets are equipped with fixed orifices and no adjustment
is necessary. Gas burner manifold is set at 3.5" W.C. (Water Column) for natural gas,
and 10" W.C. (Water Column) for propane gas.
After piping has been checked for leaks, all piping receiving gas should be fully purged
to remove air.
ELECTRICAL CONNECTION
WARNING: ELECTRICAL GROUNDING INSTRUCTIONS
This appliance is equipped with a three-prong (grounding) plug for your
protection against shock hazard and should be plugged directly into a
properly grounded three-prong receptacle. Do not cut or remove the
grounding prong from this plug. (120V units only).
The electrical wiring diagram is located inside the left-hand skillet console.
The wiring compartment is located in the left hand control console. For units operated
on electrical supply other than 120 volts, remove the left hand console cover and make
electrical connections per the wiring diagram located inside. The skillet must be
grounded in accordance with requirements of the National Electrical Code or applicable
local code.
Replace console cover.
8
WARNING: For an appliance equipped with casters, the installation shall
be made with a connector that complies with the Standard for Connectors
for Moveable Gas Appliances, ANSI Z21.69-CSA 6.16 and a quick-
disconnect device that complies with the Standard for Quick-Disconnect
Devices for Use with Gas Fuel, ANSI Z21.41-CSA 6.9; adequate means must
be provided to limit the movement of the appliance without depending on
the connector and the quick-disconnect device or its associated piping to
limit the appliance movement; the location where the restraining means
may be attached to the appliance is the bottom rear of the left hand control
console.
If the unit is also equipped with an optional water fill valve it too
must be installed with a flexible water supply tube, a quick disconnect and
strain relief.
9
2.0 OPERATING INSTRUCTIONS
CAUTION: The appliance and its parts are hot. Use care when operating,
cleaning and servicing the appliance.
BEFORE FIRST USE
Using a non-corrosive, grease-dissolving commercial cleaner, clean the protective metal
oils from all surface parts and the interior of the tilting braising pan. Follow the cleaner
manufacturer’s directions. Rinse thoroughly and drain the pan. Wipe dry with a soft
clean cloth.
LIGHTING
CAUTION: If you smell gas during the lighting procedure, immediately shut
off the gas supply until the leak has been corrected.
WARNING: In the event of main burner ignition failure, a 5 minute purge
period must be observed prior to re-establishing ignition source.
1. Open the manual gas shut-off valve located under the left hand console, when facing
the front of the unit.
2. Ensure that the skillet pan is in the down or horizontal position.
3. Turn the “POWER” switch “ON”.
4. Set the thermostat dial to the desired setting. The red “TEMPERATURE” pilot will be
on until the desired setting has been reached.
5. The green “IGNITION” pilot should remain on with the “TEMPERATURE” pilot,
indicating normal ignition and operation. If the “IGNITION” pilot goes off while the
“TEMPERATURE” pilot remains on, this indicates that the system has failed to ignite
the burners. A five minute period of complete shut off is required before restarting.
6. When the skillet has reached the setting, both pilots will go off, indicating the unit has
reached the set temperature and that the burners are off. The unit will cycle on and
off to maintain the set temperature.
7. Turn the “POWER” switch to “OFF” when the skillet is not in use and close the
manual gas shut-off valve.
10
DAILY SHUTDOWN PROCEDURE
1. Turn skillet off, turn thermostat dial to off; turn power switch off.
2. Close manual gas shut-off valve.
TO TILT BRAISING PAN
1. Lift lid.
2. Turn handwheel clockwise to desired position.
3. To return pan to horizontal position, turn handwheel counterclockwise.
4. DO NOT ATTEMPT TO TILT PAN WITH LID DOWN.
NOTE: When the pan is tilted a safety switch will automatically turn off gas supply.
The skillet will not operate once the pan has been tilted.
Autres manuels pour BLT-30G
2
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Blodgett Poêlon
Blodgett
Blodgett BLG-30G Manuel utilisateur
Blodgett
Blodgett BLG-30G Manuel du propriétaire
Blodgett
Blodgett BCH-30G Manuel utilisateur
Blodgett
Blodgett BTT-16G Manuel utilisateur
Blodgett
Blodgett BTT-16G Manuel du propriétaire
Blodgett
Blodgett BLT-30G Manuel utilisateur
Blodgett
Blodgett BTT-16G Manuel utilisateur
Blodgett
Blodgett BLP-30G Manuel utilisateur
Blodgett
Blodgett BLT-30G Manuel utilisateur
Blodgett
Blodgett BCH-30G Manuel du propriétaire
Manuels Poêlon populaires d'autres marques
Presto
Presto 6851 Manuel utilisateur
Mellerware
Mellerware ALONZO Manuel utilisateur
Black & Decker
Black & Decker Multi-Cuisine Grande SKG605 Series Instructions d'installation
Sheffield
Sheffield PLA1240 Manuel utilisateur
Elma
Elma 14.36.1 Manuel utilisateur
RM Gastro
RM Gastro BR-50-78G Manuel utilisateur
