Blitz BZA2290 Manuel utilisateur
OWNER'S MANUAL
BZA-2290/BZA-2390
BZA-2490/BZA-4190
BRIDGEABLE MOSFET
POWER AMPLIFIERS
Table of Contents
Table of Contents
8
1
2
3~7
9~11
9
10~11
12
Troubleshooting
Wiring 13
Introduction
Introduction & Features
Features
Congratulations on your purchase of a BLITZ amplifier.
You have purchased a quality product designed and engineered to
give you many years of uncompromised musical service.
BLITZ amplifiers are designed with the latest technology available,
incorporating a DC to DC Switching Power Supply, which provides
headroom for even the most demanding peaks and dynamic ranges
found on modern CD's and recordings.
Electronic Crossover Network
Bass Boost Circuit
Bridgeable at 4 Ohms
2 Ohm Stereo Stable
Tri-Mode Capable
Gold plated RCA Inputs
Line Outs for Left and Right Channel
Line Outs for 1/2 Channel(BZA-4290 only)
Low Pass Filter Controls
High Pass Filter Controls
Remote Bass Level Control (Optional)
Power and Protection LED Indicators
BLUE Lighting Illumination
6+6 LED Level meter
Soft Turn-on/Turn-off
1
Specification
Specification
BZA-2390 BZA-2490
RMS at 4 Ohms
MAX at 4 Ohms
MAX at 4 Ohms
BRIDGED
MAX at 4 Ohms
BRIDGED
RMS at 2 Ohms
VARIABLE HIGH PASS
VARIABLE LOW PASS
T.H.D
S/N RATIO
Input Sensitivity
Channel Separation
FREQ. Response
Dimensions (W x H x L)
BZA-2290
2 X 130W
2 X 400W
1 X 500W
2 X 200W
40Hz~3KHz
40Hz~350Hz
<0.04%
>90dB
100mV ~ 4V
>65dB
10Hz ~ 30KHz
10" X 2.17"
X 7.9"
2 X 150W
2 X 500W
1 X 60 0 W
2 X 250W
40Hz~3K0Hz
40Hz~350Hz
<0.04%
>90dB
100mV ~ 4V
>65dB
10" X 2.17"
X 8.7"
2 X 250W
2 X 800W
1 X 950W
2 X 400W
40Hz~3KHz
40Hz~350Hz
<0.04%
>90dB
100mV ~ 4V
>65dB
10" X 2.17"
X 9.8"
BZA-4190
4 X 100W
4 X 250W
2 X 400W
4 X 150W
40Hz~3KHz
40Hz~350Hz
<0.04%
>90dB
100mV ~ 4V
>65dB
10" X 2.17"
X 11.4"
2
10Hz ~ 30KHz 10Hz ~ 30KHz 10Hz ~ 30KHz
Features & Controls
BZA-2290 / BZA-2390 / BZA-2490
FULL
LPF HPF
40 350
REMOTE
PROT.
PWR.
ONOFF
BASS
BOOST
LOW
PASS MODE HIGH
PASS
INPUT
LEVEL
MIN MAX
LINE
INPUT
LINE
OUT
R
L
40 3K
Features & Controls
123 4 56 7 8
3
SPEAKER
FUSE
+12V
+REM
GND
POWER
BRIDGED MODE
RL
13 10 11 12
Features & Controls
Features & Controls
BZA-4190
4
BASS
BOOST
MIN MAX
HIGH
PASS
40 3K
40 350
ONOFF FULL LPF HPF
3/4 CH
REMOTE
PROT.
PWR.
INPUT
LEVEL
LOW
PASS
MODE
LINE
INPUT
LINE
INPUT
LINE
OUT
Ch3
Ch4
Ch1
Ch2
40 350
LOW
PASS
HIGH
PASS
40 3K
MODE
HPF LPF FULL ON OFF
BASS
BOOST
INPUT
LEVEL
MIN MAX
CHANNEL 1+2CHANNEL 3+4
11 2
3
654 2 67 78
4
5
3
FUSES
SPEAKER
+12V
+REM
GND
POWER
BRIDGED BRIDGED
CH1 CH2 CH3 CH4
13
9
10 11 12
Features & Controls
Features & Controls
1.REMOTE CONTROL INPUT ( Pig-1 )
2.BASS BOOST SWITCH - ON and OFF
3.VARIABLE LOW-PASS FILTER(40Hz ~ 350Hz)
When Crossover Mode Selector is in Low Pass Mode, this control limits
the frequencies which will be distributed to the speakers to those below
the value to which this is set within the range 40~350Hz.
4.MODE CONTROL
Adjust the crossover for your chosen installation method.
-LPF : Low pass filter- only bass tones go to speakers. Use with woofer or
sub-woofer.
-HPF : High pass filter - blocks very low tones from the speakers.
-FULL : No filter - all tones go to speakers. Use with full-range speakers,
or with external crossovers.
5.VARIABLE HIGH-PASS FILTER(40Hz ~ 3kHz)
When Crossover Mode Selector is in High Pass Mode, this control limits
the frequencies which will be distributed to the speakers to those above
the value to this is set within the range 40Hz~3kHz.
6.INPUT LEVEL(INPUT SENSITIVITY ADJUSTMENT)
This control adjust the amplifier's input sensitivity. Input sensitivity is
variable from 100Millivolts to 4 volts. Clockwise increases sensitivity.
Counterclockwise decreases sensitivity.
This knob is not a volume control signal levels. A lower signal level will
require increased sensitivity for full power. A higher signal level will
require decreased sensitivity.
7.LINE INPUT RCA JACKS
These inputs are for signal cables from the source. Always use high
quality shielded RCA cables.
8.LINE OUT RCA JACKS
The LINE OUT allows you to build multiple amplifier systems without
having to use splitter cords to distribute the signal. Now it is simple
a matter of bringing one set of RCAs into the first amplifier, then
using the line out RCA jacks as the feed to the next amplifier.
5
9.LED Indicator
- POWER : This GREEN LED will illuminate when the amplifier is turned
"ON". If it fails to illuminate, check the power connections to
the Amplifier and fuses.
- PROTECTION : The amplifier protection circuitry will disable the amplifier
if input overload, short circuit or extremely high
temperature conditions are detected. When the
protection mode is in operation, the LED indicator on the
side panel will be illuminated, indicating the amplifier has
gone into a self preservation mode.
If you observe that the Protection LED is lit, please check the system
carefully to determine what has caused the protection circuit to engage.
The amplifier can be reset by turning the remote power off and then on
again. If the amplifier shut down due to a thermal overload condition,
please allow it to cool down before restarting. If the amplifier shut down
because of an input overload or short circuit, be sure to repair these
conditions before attempting to power up the amplifier again.
10.B- TERMINAL (CHASSIS GROUND)
To avoid unwanted ignition noise caused by ground loops, it is essential
that the Amplifier be grounded to a clean, bare, metal surface of the
vehicles chassis.
11.REMOTE POWER ON
To remote wire car stereo. This amplifier is turned "ON" remotely when
vehicle's stereo is turned "ON".
Note: IF YOUR RADIO DOES NOT HAVE +12 VOLT OUTPUT LEAD WHEN
TURNED ON, THE "REMOTE" TERMINAL ON THE AMPLIFIER CAN BE
CONNECTED TO VEHICLES ACCESSORY CIRCUIT WHICH PROVIDES
+12V WHEN THE CAR IS ON.
Features & Controls
Features & Controls
6
MAXMIN
LEVEL
REMOTE
PROT.
PWR.
Features & Controls
Features & Controls
MAX
MIN
LEVEL
Fig 1.
Remote Bass Level Control : Optional
Remote Bass Boost Control : This control adjusts the Bass Boost gain for the
amplifier's speaker output (0 - +12dB)
12.B+ TERMINAL (BATTERY POSITIVE)
Due to the power requirements of the Amplifier, this connection should
be made directly to the positive(+) terminal of battery. For safety measure,
install an in-line fuse Holder (not included) as close to the battery
positive(+) terminal as possible with an ampere rating not to exceed total
value of fuses in Amp.
13.SPEAKER TERMINAL
7
Installation & Precautions
Installation
1. Find a suitable location in the vehicle to mount the amplifier.
2. Make sure there is sufficient air flow around the intended mounting
location.
3. Bolt the amplifier to the mounting surface.
4. Connect the power ground terminal to the nearest point on the chassis
of the car. Keep this ground wire less than one meter (39") in length.
Use 8 gauge wire.
5. Connect the remote terminal to the remote output of the head unit using
14 gauge wire.
6. Connect an empty fuse holder within 300 mm (12") of the battery and run
8 gauge or larger high quality cable from this fuse to the amplifier location.
7. Make sure there is no fuse in this fuse holder. Then make the connection
to the "BATT"connection on the amplifier.
8. If multiple amplifiers are being used, use cables (each with it's own fuse
at the battery) or a # O or #2 cable from the fuse holder at the battery to
a distribution block at or near the amplifier's location.
9. Connect all line inputs and outputs using high-quality RCA-RCA cables.
10. Insert fuse(s) at the battery fuse holder(s).
11. Recheck all connections before powering up.
12. Set all level controls to their least sensitive positions and set all
crossover controls, switches, etc. To the desired frequency or position.
13. Once the system is powered up, set the volume control on the head unit
to about the 2 O'clock position, and then set all the amplifiers' level
controls for maximum output level.
14. Further fine tuning of the various controls may be m\necessary to
obtain the desired results.
Precautions
1. Before you drill or cut any holes, investigate your car's layout very carefully.
Take care when you work near the gas tank, fuel lines, hydraulic lines and
electrical wiring..
2. Do not operate the amplifier when it is unmounted. Attach all audio system
components securely within the automobile to prevent damage, especially in
an accident
3. Do not mount this amplifier so that the wire connections are unprotected or
in a pinched condition, or likely to be damaged by nearby objects. Be sure to
select a location inside your vehicle which has adequate ventilation..
4. Before making or breaking power connections in your system, disconnect the
vehicle battery. Confirm that your head unit or other equipment is turned off
while connecting the input jacks and speaker terminals.
5. If you need to replace the power fuse, only replace it with a fuse identical to
that supplied with the system. Using a fuse fo a different type or rating may
result in damage to your system which isn't covered by the manufacturer's
warranty.
8
Ce manuel convient aux modèles suivants
3
Table des matières
Autres manuels Blitz Amplificateur de voiture
