Blagdon 1057233 Manuel utilisateur
DESIGN
INNOVATIVE
Lithium Battery Powered
Solar Recharged
Part No. Description Spares
1Solar Panel with Battery
pack
1057288
Battery only
1057301
2Solar Panel Post and Bracket
3Solar Panel Post
Ground Spike
4Solar Panel Post Wall
Mounting Bracket
5Fountain Fittings
6LED Light 1057295
7Pump 1057318
8Pump Float
9Mesh Bag – Float Anchor
10 Indoor mains power/charger
cable (1.5m + 5m extension) 1055901
Single Jet Star Jet
7 Hole
Daisy Jet 12 Hole
Daisy Jet
Flow
Control
Valve
3
/
8”and
1
/
2” Hose
Adaptors
Fountain
extension
pipe x4
50mm
5.
6.
7.
9.
8.
1. Solar panel installation.
Ground mounted: Wall/fence mounted:
Ground mounted: Insert solar panel bracket into one end of the tube, insert the ground spike into the opposite
end, and push into your chosen area of ground.
Wall/fence mounted: Using the supplied wall plugs and screws, attach the wall/fence mounting bracket to
your chosen wall or fence. Next slide on the tube, followed by the solar panel bracket.
Once you have mounted the bracket in your chosen location slide the lip on the reverse of the solar panel into
the groove present on the bracket. Then using the wingnut adjust the angle of the panel to between 30° and
45° from vertical.
Important:
The solar panel must face as
close to South as possible, with
no obstruction from buildings,
shrubs or trees, to ensure that it
receives the optimal amount of
sunlight to charge the battery
effectively.
2. Pump assembly.
1. Attach the pump outlet adaptor to the pump.
2. Connect the flow control valve to the pump outlet adaptor – this will allow you to adjust the water flow (not
required for deep water/floating).
3. Connect the correct amount of extension tubes to raise the outlet above the water surface. (For deep water/
floating installation only one extension will be required)
4. Push the top extension pipe through the LED ring.
5. Connect the fountain head adaptor to the end of the top extension pipe.
6. Attach your chosen fountain head – if you have chosen the single jet, it can simply be connected to the
extension pipe in place of the fountain head adaptor.
Deep water/floating only:
•After attaching the extension pipe to the pump, push the pipe through the hole cut out on the float prior to
installing the LED.
•Fill the supplied mesh bag with gravel, and attach to the pump using the string – adjust the length according
to the depth of the pond in the location you would like the pump to be.
Important:
Only the correct, official Blagdon Liberty battery pack should be used for replacement, as alternatives may in
incompatible, they may damage the system or create an electrical hazard – this will void the guarantee.
Do not place the removed battery in or near fire, or in direct sunlight. Heating the battery can damage the
safety circuitry, which can cause additional heating, rupture or ignition of the battery.
1
2
345
Table des matières
Autres manuels Blagdon Pompe de bassin
Blagdon
Blagdon Amphibious IQ Series Manuel utilisateur
Blagdon
Blagdon MINIPOND 2000 Manuel utilisateur
Blagdon
Blagdon Hydratech Torrent 3000 Manuel utilisateur
Blagdon
Blagdon inpond 5 in 1 3000 Manuel utilisateur
Blagdon
Blagdon AMPHIBIOUS Series Manuel
Blagdon
Blagdon Force hybrid 5000 Manuel utilisateur
Blagdon
Blagdon Koi Air 25 Manuel
Manuels Pompe de bassin populaires d'autres marques
TeichTip
TeichTip Sunsun Bio Pond Filter Set Manuel utilisateur
Hozelock Cyprio
Hozelock Cyprio Cascade 5500 Manuel utilisateur
Hozelock Cyprio
Hozelock Cyprio Aquaforce Series Manuel utilisateur
HEISSNER
HEISSNER SPF 150-00 Manuel utilisateur
AquaScape
AquaScape AQUAFORCE 4000-8000 Instructions d'utilisation
Messner
Messner system-X 1501 Manuel utilisateur