Blackview X1 Manuel utilisateur
User Manual
Please read and understand the manual
Bind watch
1
Correct operation:Scan the
QR code below or download
“H Band” APP through the
mobile APP store to pair with
the watch
Wrong operation: Pair the
watch directly with the
Bluetooth in your mobile
phone's settings.
Bluetooth
2
Product Parameters:
M
odel X1 Screen Size 1.3 inches
Battery
c
apacity
260mAh
Charging
voltage
5V±0.2V
C
harging time 2.5hours Battery life 10 days
Waterproof
l
evel
5ATM Standby time 45 days
O
perating
t
emperature
-20 --45 Bluetooth
version
BLE5.0
S
creen
m
aterial
Corning Gorilla
3 generation
Strap width 22mm
Product Introduction
1. Slide up or down on the dial interface to switch the dial display.
2. Slide left or right on the dial interface sliding operation to switch to the shortcut
function display, which has the day's movement data, sleep detection, watch information,
function menu, etc.
3
Introduction To the Connection between Watch and Mobile Phone
1. Download and install APP (H Band)
Scan the QR code on the box or the built-in QR code on the watch via the mobile browser program
to download. Downloading needs WIFI network or data traffic. Install it after downloading, open the
APP after the installation, and give the software corresponding rights which are needed for Bluetooth
connection. (Note: H Band supports IOS9.0 or later and Android6.0 or later)
(H Band QR Code)
2. The way to connect the watch to the phone (same for iOS and Android)
Turn on the Bluetooth of the mobile phone, and then open the H Band on the mobile phone desktop
(Figure 1). You can choose to log in without an account or register with an account. After the
successful login, go to the home page. On the home page, click the red part "not connected" to the
Bluetooth search interface (Figure 2). Select the corresponding device (X1) and click to connect.
Wait for a few seconds, it will prompt the watch to make a Bluetooth pairing request with the mobile
phone. Please allow Bluetooth pairing. This completes the pairing connection between the mobile
phone APP and the watch (Figure 3). Then, it will ask if you want to upload data to the cloud (Figure
4). This operation can be selected by yourself. Clicking NO or YES will enter the connection success
interface and synchronize the data once (Figure 5). (Note: The sync data function is automatically
uploaded every 30 minutes. If you turn on the automatic heart rate monitoring function, the heart rate
is tested once every 10 minutes and then uploaded to the APP.)
4
Important:
If the Apple mobile phone is not used for a long time (2 hours), in standby or
hibernation (in a state of blank screen), H Band may be cleaned by the Apple's
IOS system. When the connection of the APP and a watch is in the off state, the
APP function will not be able to use. Open the APP again, it will automatically
reconnect on watch.
After installing the APP on the android phone, you need to open the background
application startup permission in the Settings of the phone, which is different for
each phone. Take Huawei mobile phone as an example, the steps are as follows:
Setting - Application -Application Startup Management-H Band, find the
applicationchange the automatic management to manual management, and open
all permissions (allow self-startup, allow associated start, allow background
activities). This work is only for the application to keep the Bluetooth connection
with the watch without the Android system cleaning up when the phone is in
standby (the phone has no bright screen).
(Figure 1) (Figure ５)
(Figure 2) (Figure ３) (Figure ４)
5
Watch Function Introduction
1. Heart Rate
Find the Heart Rate function in the Function Menu interface, click the Heart Rate icon to open and
start the heart rate test. The test lasts for 60 seconds and then thescreen will automatically turn off
after the test. Before the test, please remain sitting still, do not wear the watch too tight or too loose
for ensuring data accuracy.
2. Multisport
Find the Multisport function in the function menu interface, click the multisport icon to enter the
sport mode. The watch provides 9 types of sports: outdoor run, outdoor walk, indoor run, indoor
walk, hiking, climbing, outdoor cycle, stationary bike, and elliptical.
3. Message
This function can be set in the APP settings, when set it to "on", mobile phone received the
application (calls, text messages, QQ, WeChat, Facebook, twitter, Linkedlh, whatsApp, Line,
lnstagram, snapchat, skype, Gmail, other, etc.) when the messages are pushed, the watch shows
content (IOS need pairing; Android permission needs opening; equipment can push the normal tips).
The watch only can store 3 messages at most.
4. Find My Phone
Find out Find My Phone function in the function menu interface, click open the search function to
6
find the phone. If the mobile phone is connecting to the watch, the phone will vibrate and ring. If
in the off state, "unconnected Bluetooth" prompt will be displayed.
5. Music
Find the Music function in the Function Menu interface, click to open to enter the music control
interface. If the mobile phone and watch are connected, click the corresponding play, the
previous song, the next song, and pause to control the music playing on the phone player. If in the
off state, "unconnected Bluetooth" prompt will be displayed. (Note: There may be compatibility
issues due to thelarge number of playback software and the large number of Android phone
manufacturers. Under normal circumstances, you can directly control the phone's music play
from the watch. Some music play software needs to be opened before you can control it.)
6. Stopwatch
Find the Stopwatch function in the Function Menu interface, click to open the Stopwatch
function, click the start button in the lower right corner to start the timer, click the button again to
pause the timer, or click the button in the lower left corner to restore the timer. The screen will be
turned off after one minute of turning on the stopwatch. By wake screen on wrist raise function or
press the power button to wake up, the stopwatch interface will be displayed. The stopwatch
cannot be exited during timing. You need to click the Restore button in the lower left corner to
restore, then swipe from left to right or short press the power button to exit the Stopwatch
function. turning on the stopwatch. By wake screen on wrist raise function or press the power
button to wake up, the stopwatch interface will be displayed. The stopwatch cannot be exited
during timing. You need to click the Restore button in the lower left corner to restore, then swipe
from left to right or short press the power button to exit the Stopwatch function.
7. Time Countdown
Find the Time Countdown function in the Function Menu interface, click to open, and you can set
the hours, minutes and seconds to count down. After setting the time, click Start to return to the
7
Function Menu. The countdown will continue in the background. When the countdown is
completed, there will add the pop-up window and vibrates to remind.
8. Settings
Find the Settings function in the function menu interface, click to open the Setting function, you
can set the Brightness adjustment and download the APP QR code. Brightness adjustment is
divided into 3 levels, which can be adjusted according to their own needs. The higher the
brightness is, the greater the power consumption will be. Scan QR code of APP to download H
Band.
Mobile APP function introduction
Notes: The APP sync data function synchronizes the step data and the heart rate data
automatically every 30 minutes. If you turn on automatic heart rate monitoring, the test will be
performed every 10 minutes and the data will be uploaded to the APP.
1.Message Reminder
Turn on "H Band"-> My-> My device-> Message Reminder, you can freely control the function
switch which can push messages to the watch. If the functionswitch is off, the messages cannot
be pushed to the watch; if it is on, the messages are normally pushed to the watch. (Note: If you
can't switch normally, please click the help in the upper right corner to troubleshoot)
2.Alarm Clock Setting
Open "H Band"-> My-> My device-> Alarm Reminder-> click the upper right corner '+', set the
time and date of the reminder (if you set a Repeat Alarm, select the Repeat Time)-> click the top
3.Sedentariness setting
Open "H Band" --> My--> My equipment--> Sedentariness reminder--> turn on --> click to
enter the setting page (set the start and end time as well as sedentariness judging interval) -->
save. The default is 14:00 p.m.-18:00 p.m. and reminding every 60 minutes.
8
When it is "on", the user can set the sedentariness judging interval and the watch shall start to
continuously monitor the user to confirm whether he or she is sitting. In case the user keeps sitting
for more than the set time period, the watch will vibrate and display the sedentariness reminder
interface.
4.Heart rate alarming
Open "H Band" --> My--> My equipment--> Heart rate alarming --> turn on --> click to enter the
setting page (set the alarming value) --> save. The default is 115bpm. In case the heart rate is
detected equal to or higher than the set value, the watch will vibrate to remind the user.
5.Binding equipment
Open "H Band" --> My--> My equipment --> Binding equipment --> turn on.
After unlocking this function, when the watch syncs the data to APP, APP shall save the data
locally (if the user logs in without using any account) or upload to cloud (in case the user logs with
certain account).
6.Firmware update
Open "H Band" --> My --> My equipment --> Firmware update.
In case there’s any new edition of the equipment program, connect APP and it shall remind the
firmware updating.
7.Clear data
Open "H Band" --> My --> My equipment --> Clear data.
Once this operation is started, the watch shall eliminate all the data and the on-off state of all the
functions shall be recovered to default.
9
Autres manuels pour X1
1
Table des matières
Langues :
Autres manuels Blackview Montre
