BLACK NOISE SAM-C Manuel

Introduction

SAM-C

Build instructions

Configure your SAM-C

SAM-C has two modes:

A - crossfader

B - S.A.M.

To configure your module as a crossfader, make

sure the Ajumpers-pads are soldered, the B

jumpers-pads must not be soldered.

You can use desoldering wire to remove the solder

from the jumpers-pad.

To configure your module, the S.A.M Bjumpers-pads

must be soldered bridged and the Ajumpers-pads

must be unsoldered.

You can use desoldering wire to remove the solder

from the jumpers-pad.

Prepare resistors

the resistors must be soldered upright.

Bend one of the legs for each of the

resistors as in the picture.

SAM-C

Build instructions

Thank you for purchasing of SAM-C.

For our first 0HP module, we wanted to take advantage of the benefits of passive

modules. But we also wanted to incorporate as many features as possible.The result

is SAM-C, a small module that takes up no space in your rack and can perform many

simple but useful utility functions.

BLACK NOISE warrants the contents of this kit to be free of defects in materials or workmanship and

to be conform with the specifications at the time of shipment for a period of two years from the date

of purchase.

We do not warrant, and we do not repair or take in modules to troubleshoot end-user DIY build faults

or second hand DIY products.

BLACK NOISE cannot be held responsible for any damage caused by one of our DIY kits and resulting

from an end-user DIY build faults.

If you encounter problems in the assembly you can contact us at: contact@blacknoisemodular.com

Contents of kit

1- SAM-C PCB x1

2- SAM-C Faceplate x1

3- 10K resistors x3

4- 100K resistors x2

5- 3.5mm Jack socket mono x3

6- Potentiometer B100K x1

7- Small knob x1

Sourced

Warranty

BSam

ACrossfader

SAM-C

Build instructions

Install the 10K resistors

Place the 10K resistors R1, R2 and R5 as

shown in the picture. Do not solder the

resistors yet.

Install the 100K resistors

Place the 100K resistors R3 and R4 as

shown in the picture. Do not solder the

resistors yet.

SAM-C

Build instructions

Install the potentiometer

Install the potentiometer, do not solder it

yet.

Install the jack sockets

Install the jack sockets, don't solder it yet.

SAM-C

Build instructions

Install the faceplate

The faceplate has two sides, on one side

it says SAM below the potentiometer, on

the other side it says Crossfader. Place

the faceplate for which indicates the

selected mode.

Install the potentiometer nut

Place the nut of the potentiometer and

screw it.

SAM-C

Build instructions

Install the jack sockets nuts

Place the nuts of the jack sockets and

screw them.

Solder the components

Turn over your module and solder the

components starting with jack sockets,

the potentiometer and the resistors.

SAM-C

Build instructions

Cut the legs of the components

Once soldered, you can cut the legs of the

resistors as close as possible to the PCB.

Clean the PCB

Clean the PCB of flux and solder residue

using Isopropyl alcohol.

SAM-C

Build instructions

Install the knob

Place the potentiometer fully

anti-clockwise and place the knob. Press

down lightly. Turn the potentiometer fully

clockwise to ensure that the knob is

correctly placed. If it is not correctly

placed correct the position and repeat the

operation. Once the knob is correctly

placed push it on the shaft of the

potentiometer.

Test your SAM-C

You can now test your SAM-C. To learn

more about the different modes you can

consult the manual using the QR code

below.

Scan to

access the

SAM-C manual

Table des matières

Autres manuels BLACK NOISE Équipement d'enregistrement

BLACK NOISE

BLACK NOISE PIPE Manuel utilisateur

BLACK NOISE

BLACK NOISE MIXER4 Manuel utilisateur

BLACK NOISE

BLACK NOISE DUAL MULTI Manuel

BLACK NOISE

BLACK NOISE QBI Manuel utilisateur

BLACK NOISE

BLACK NOISE SAM-C Manuel utilisateur

BLACK NOISE

BLACK NOISE COSMOS Manuel

BLACK NOISE

BLACK NOISE DRII Manuel utilisateur

BLACK NOISE

BLACK NOISE SALLEN KEY Manuel utilisateur

BLACK NOISE

BLACK NOISE DR II - S Manuel

BLACK NOISE

BLACK NOISE DRII Manuel

BLACK NOISE

BLACK NOISE EG-LFO II Manuel utilisateur

BLACK NOISE

BLACK NOISE Dual Rectifier II - S Manuel utilisateur

BLACK NOISE

BLACK NOISE GOMA Manuel

BLACK NOISE

BLACK NOISE GOMA Manuel utilisateur

BLACK NOISE

BLACK NOISE SALLEN KEY Manuel

BLACK NOISE

BLACK NOISE QBI Manuel

Manuels Équipement d'enregistrement populaires d'autres marques

KV2 Audio

KV2 Audio 500 Series Manuel utilisateur

Robotics Technologies

Robotics Technologies microBus-Cam II Manuel utilisateur

Seca

Seca 460 Manuel utilisateur

Cognex

Cognex MVS-8000 Series Manuel utilisateur

Mect

Mect MPNC006 Series Manuel utilisateur

Bad Caf

Bad Caf THE LEASH Manuel utilisateur

Strymon

Strymon NIGHTSKY Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Manuel utilisateur

Tews Technologies

Tews Technologies TPMC465 Manuel utilisateur

Honeywell

Honeywell Excel 50 Manuel utilisateur

SeaLevel

SeaLevel COMM+8.LPCI Manuel utilisateur

Arturia

Arturia AUDIOFUSE STUDIO Manuel utilisateur

Rukra

Rukra RK-1240 Manuel utilisateur

Samson

Samson SCOM Manuel utilisateur

Dynacord

Dynacord DPS260 Manuel utilisateur

Nice

Nice Core Manuel utilisateur

Pyle Pro

Pyle Pro PSS8 Manuel utilisateur

RF-System

RF-System TinyGate Manuel d'utilisation et d'entretien