Black Box IC442A-R2 Manuel utilisateur

CUSTOMER

SUPPORT

INFORMATION

Order toll-free in the U.S.: Call 877-877-BBOX (o tside U.S. call 724-746-5500)

FREE technical s pport 24 ho rs a day, 7 days a week: Call 724-746-5500 or fax 724-746-0746

Mailing address: Bla k Box Corporation, 1000 Park Drive, Lawrence, PA 15055-1018

Web site: www.bla kbox. om • E-mail: info@bla kbox. om

JUNE 2002

IC442A-R2

RGB Video Baluns

RED

VIDEO

PAIR 4

(7 & 8)

GREEN

VIDEO

PAIR 2

(3 & 6)

BLUE

VIDEO

PAIR 3

(1 & 2)

RGB Vide Balun

FCC/IC RFI STATEMENTS, TRADEMARKS

FEDERAL COMMUNICATIONS COMMISSION AND INDUSTRY CANADA

RADIO-FREQUENCY INTERFERENCE STATEMENTS

Class B Digital Device. This equipment has been tested and found to comply with the

limits for a Class B computing device pursuant to Part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful interference

in a residential installation. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or telephone reception,

which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

• Consult an experienced radio/TV technician for help.

Caution: Changes or modifications not expressly approved by the party responsible

for compliance could void the user’s authority to operate the equipment.

To meet FCC requirements, shielded cables are required to connect this device to

other Class B certified devices.

This digital apparatus does not exceed the Class B limits for radio noise emission from digital

apparatus set out in the Radio Interference Regulation of Industry Canada.

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites

applicables aux appareils numériques de classe B prescrites dans le Règlement sur le brouillage

radioélectrique publié par Industrie Canada.

TRADEMARKS USED IN THIS MANUAL

BLACK BOX and the logo are registered trademarks of Black Box

Corporation.

VELCRO is a registered trademark of Velcro USA Inc.

Any other trademarks mentioned in this manual are acknowledged to be the property of the

trademark owners.

RGB VIDEO BALUNS

NORMAS OFICIALES MEXICANAS (NOM)

ELECTRICAL SAFETY STATEMENT

INSTRUCCIONES DE SEGURIDAD

1. Todas las instrucciones de seguridad y operación deberán ser leídas antes de

que el aparato eléctrico sea operado.

2. Las instrucciones de seguridad y operación deberán ser guardadas para

referencia futura.

3. Todas las advertencias en el aparato eléctrico y en sus instrucciones de

operación deben ser respetadas.

4. Todas las instrucciones de operación y uso deben ser seguidas.

5. El aparato eléctrico no deberá ser usado cerca del agua—por ejemplo, cerca

de la tina de baño, lavabo, sótano mojado o cerca de una alberca, etc..

6. El aparato eléctrico debe ser usado únicamente con carritos o pedestales que

sean recomendados por el fabricante.

7. El aparato eléctrico debe ser montado a la pared o al techo sólo como sea

recomendado por el fabricante.

8. Servicio—El usuario no debe intentar dar servicio al equipo eléctrico más allá

a lo descrito en las instrucciones de operación. Todo otro servicio deberá ser

referido a personal de servicio calificado.

9. El aparato eléctrico debe ser situado de tal manera que su posición no

interfiera su uso. La colocación del aparato eléctrico sobre una cama, sofá,

alfombra o superficie similar puede bloquea la ventilación, no se debe colocar

en libreros o gabinetes que impidan el flujo de aire por los orificios de

ventilación.

10. El equipo eléctrico deber ser situado fuera del alcance de fuentes de calor

como radiadores, registros de calor, estufas u otros aparatos (incluyendo

amplificadores) que producen calor.

11. El aparato eléctrico deberá ser connectado a una fuente de poder sólo del

tipo descrito en el instructivo de operación, o como se indique en el aparato.

NOM STATEMENT

12. Precaución debe ser tomada de tal manera que la tierra fisica y la polarización

del equipo no sea eliminada.

13. Los cables de la fuente de poder deben ser guiados de tal manera que no

sean pisados ni pellizcados por objetos colocados sobre o contra ellos,

poniendo particular atención a los contactos y receptáculos donde salen del

aparato.

14. El equipo eléctrico debe ser limpiado únicamente de acuerdo a las

recomendaciones del fabricante.

15. En caso de existir, una antena externa deberá ser localizada lejos de las lineas

de energia.

16. El cable de corriente deberá ser desconectado del cuando el equipo no sea

usado por un largo periodo de tiempo.

17. Cuidado debe ser tomado de tal manera que objectos liquidos no sean

derramados sobre la cubierta u orificios de ventilación.

18. Servicio por personal calificado deberá ser provisto cuando:

A: El cable de poder o el contacto ha sido dañado; u

B: Objectos han caído o líquido ha sido derramado dentro del aparato; o

C: El aparato ha sido expuesto a la lluvia; o

D: El aparato parece no operar normalmente o muestra un cambio en su

desempeño; o

E: El aparato ha sido tirado o su cubierta ha sido dañada.

RGB VIDEO BALUNS

Contents

Chapter Page

1. Specifications ............................................................................................. 5

2. Introduction ............................................................................................... 7

3. Installation .................................................................................................. 8

4. Troubleshooting ...................................................................................... 10

4.1 Things to Try If Problems Occur ..................................................... 10

4.2 Calling Black Box .............................................................................. 11

4.3 Shipping and Packaging ................................................................... 11

CHAPTER 1: Specifications

1. Specifications

Cable Required: Between Balun pairs: Unshielded twisted pair (UTP):

Construction Standard: Category 3 or higher;

Gauge: 24 AWG or lower;

Termination: RJ-45 plugs;

Pairs: 3 or more (6 wires used);

Impedance: 100 ohms at 1 MHz;

Maximum Capacitance: 20 pF/ft. (6.1 pF/m);

Maximum Attenuation: 6.6 dB/1000 ft. (2 dB/km);

To attached devices: (3) Coaxial 75-ohm RG-59/U cables

with BNC male connectors on the Balun end, preferably

the three such cables supplied with the Balun

Compliance: FCC Class B, IC Class/classe B;

CISPR Pub. 22 Class B

Standard: Composite (baseband) video: RGB

Impedance: Coaxial side: 75 ohms;

UTP side: 100 ohms

Video Bandwidth: DC to 8 MHz

Maximum RF

Input: 1.1 volts at 60 Hz

Insertion Loss: Less than 2 dB over the DC-to-8-MHz frequency range

Return Loss: Greater than 15 dB over the DC-to-8-MHz frequency range

Common-Mode

Rejection: Greater than 40 dB at 8 MHz

Maximum

Distance: With Category 3 cable: 330 ft. (100.6 m);

With Category 5 cable: 500 ft. (152.4 m)

Connectors: (1) RJ-45 female and (3) BNC female

RJ-45 Pins Used: Pins 1 (blue), 2 (blue ground), 3 (green), 6 (green ground),

7 (red), 8 (red ground)

RGB VIDEO BALUNS

Temperature

Tolerance: Operating: 32 to 131˚F (0 to 55˚C);

Storage: -4 to +185˚F (-20 to +85˚C)

Humidity

Tolerance: Up to 95% noncondensing

Enclosure: Fire-retardant plastic with included optional VELCRO®

mounting material

Size: 2.3"H x 2.4"W x 1"D (5.8 x 6.1 x 2.5 cm)

Weight: With included cables: 6.3 oz. (178.6 g);

Without included cables: 2.8 oz. (79.3 g)

CHAPTER 2: Introduction

2. Introduction

With the RGB Video Balun, you can transmit composite baseband red/green/blue

video signals across Category 3 or better unshielded twisted-pair (UTP) cable,

which is already wired into most commercial sites. Use pairs of Baluns to transmit

RGB video: The Balun near the video source takes the three composite baseband

video signals from 75-ohm coaxial cable, converts them, and transmits them over

UTP cable to the other Balun, which puts them back on coax and sends them to

their destination.

Connect the RGB Video Balun to a site’s structured cabling through a modular

wall jack in the work area. Each Balun has three BNC connectors at one end and

an RJ-45 jack at the other end.

The Video Balun is designed for use with RGB monitors, such as those often

deployed in banks, investment houses, and stock-exchange trading floors.

RGB VIDEO BALUNS

3. Installation

To install a pair of RGB Video Baluns, take these steps:

CAUTION!

D n t attempt t pen the h using. There are n user-serviceable parts

inside the RGB Vide Balun. Opening the unit will v id y ur warranty.

1. Make sure that the video-destination device is not too far away from the video-

source device (refer to the Maximum Distance specification in Chapter 1). If

the destination device is beyond the reach of the source Balun, the video

signal the device receives will be weak or nonexistent.

2. Follow the manufacturer’s instructions for turning off power to the video

equipment you will be attaching, and disconnecting that equipment from AC

power and from all other devices.

3. Make certain that the telecommunications outlets and cross-connects to

which you will connect the Baluns are configured properly and are labeled so

that the circuit can be identified.

CAUTION!

D not c nnect the RGB Vide Balun t a telec mmunicati n utlet

wired t unrelated equipment. Making such a c nnecti n may damage

the equipment and/ r the Balun. Make sure that all wiring is straight-

thr ugh-pinned.

4. Verify that the twisted-pair circuit you want to use is not already being used

for other LAN or telephone equipment.

5. Optional: Each Balun comes with VELCRO®mounting pads. To mount a

Balun to a surface, first make sure that that surface is free of dust, oil, etc., so

the VELCRO will adhere to it. Then peel off the adhesive backing, attach one

side of the pads to the Balun, and attach the other side to the surface.

CAUTION!

D not m unt the Balun ver equipment-ventilati n penings. D ing s

might damage the Balun r cause the equipment t verheat.

6. Attach each Balun to its associated RGB device with a set of three cables,

preferably the three included with the Balun. (If you use other cables, they

must have BNC male connectors on the Balun end.)

CHAPTER 3: Installation

7. Connect one end of a UTP cable to each Balun’s RJ-45 modular jack, as

shown in Figure 3-1. These cables must carry at least three wire pairs, and

these wires must be pinned to RJ-45 Pins 1, 2, 3, 6, 7, and 8.

Figure 3-1. The Balun and its connectors.

8. Plug the other end of each UTP cable into the appropriate video wall outlet

or patch panel. When this is done, a complete cabling circuit should run

between the two baluns, as shown in Figure 3-2 below.

Figure 3-2. Two Baluns cabled together.

9. Reconnect and power up the video equipment.

Your RGB Video Balun system should be ready for continuous operation.

RED

VIDEO

PAIR 4

(7 & 8)

BLUE

VIDEO

PAIR 3

(1 & 2)

GREEN

VIDEO

PAIR 2

(3 & 6)

RGB Vide Balun

RED

VIDEO

PAIR 4

(7 & 8)

BLUE

VIDEO

PAIR 3

(1 & 2)

GREEN

VIDEO

PAIR 2

(3 & 6)

RGB Vide Balun

RED

VIDEO

PAIR 4

(7 & 8)

BLUE

VIDEO

PAIR 3

(1 & 2)

GREEN

VIDEO

PAIR 2

(3 & 6)

RGB Vide Balun

RJ-45 f r UTP

Categ ry 3 r

higher UTP

Table des matières

Autres manuels Black Box Convertisseur de média

Black Box

Black Box ME660A Manuel utilisateur

Black Box

Black Box CL050A-R3 Manuel utilisateur

Black Box

Black Box AC150A-4 Manuel utilisateur

Black Box

Black Box VSC-VGA-TV Manuel utilisateur

Black Box

Black Box AC216A Manuel utilisateur

Black Box

Black Box PI125A-R2 Manuel utilisateur

Black Box

Black Box IC961A Manuel utilisateur

Black Box

Black Box IC525A-F Manuel utilisateur

Black Box

Black Box LGC5400A Manuel utilisateur

Black Box

Black Box AVSP-HDMI1X2 Manuel utilisateur

Black Box

Black Box LH1709A-SCTS-US Manuel utilisateur

Black Box

Black Box AC150A-2 Manuel utilisateur

Black Box

Black Box SP385A-R3 Manuel utilisateur

Black Box

Black Box AC336A Manuel utilisateur

Black Box

Black Box AC340A Manuel utilisateur

Black Box

Black Box LGC5134A-R3 Manuel utilisateur

Black Box

Black Box PI130A Manuel utilisateur

Black Box

Black Box G.703/V.35 Manuel utilisateur

Black Box

Black Box LPD401A Manuel utilisateur

Black Box

Black Box LGC5134A Manuel utilisateur

Black Box

Black Box LG6630C Manuel utilisateur

Black Box

Black Box IC199A-R3 Manuel utilisateur

Black Box

Black Box IC149A-R2 Manuel utilisateur

Black Box

Black Box ACU315A-R2 Fiche technique

Manuels Convertisseur de média populaires d'autres marques

SoundTraxx

SoundTraxx Blunami BLU-2200 Manuel utilisateur

SPROLINK

SPROLINK VA1 Manuel utilisateur

Acclaim Lighting

Acclaim Lighting DDC-1-AC Manuel utilisateur

Nikon

Nikon AF-S TC-20E III Manuel utilisateur

Axis

Axis AXIS Q7406 Manuel utilisateur

Omega

Omega TAC80B-J Manuel utilisateur

Zoom

Zoom Thunderbolt TAC-2R Manuel utilisateur

OST

OST iConverter 10/100M Manuel utilisateur

Vertiv

Vertiv Netsure Manuel utilisateur

birddog

birddog MINI Manuel utilisateur

Roland

Roland GI-10 Manuel utilisateur

Wallenstein

Wallenstein WX310 Manuel utilisateur

Pace

Pace MSS 200-1 Manuel utilisateur

Solar Converters

Solar Converters EQ 12/24-50 Manuel utilisateur

CYP

CYP EL-7400V Manuel utilisateur

TIE

TIE MIDI 1i1o Manuel utilisateur

DCS

DCS Vivaldi Upsampler Manuel utilisateur

Westermo

Westermo MCW-211 SERIES Manuel utilisateur