Black Box Emerald EMD4000T Manuel utilisateur

STEP X - Name of Step

24/7 TECHNICAL SUPPORT AT 877.877.2269 OR VISIT BLACKBOX.COM

EMD4000T, EMD4000R

EMERALD

KVM 4K

QUICK START GUIDE

STEP 1A - Transmitter Diagrams

2 3 6

487 79

Front panel

Back panel

STEP 1B - Transmitter Components

TABLE 1. EMD4000T COMPONENTS

NUMBER IN DIAGRAM AT LEFT DESCRIPTION DESCRIPTION

1 Power LED LED indicates power status

2 12-VDC, 3-A Power In connector Connect to supplied power adapter

3DB9 connector Connects to serial console port

4 USB Type B connector Connect to PC/workstation USB

connector

5 RJ-45 connector Connects to LAN

6DisplayPort 1.2 video connector Connect to PC Video

7 (2) SFP+ ports Dual 10G network ports

8Audio Line In Connect to PC Line Out

9 Audio Line Out Connect to PC Line In

STEP 2A - Receiver Diagrams

1234

510

710

Front panel

Back panel

STEP 2B - Receiver Components

TABLE 2. EMD4000R COMPONENTS

NUMBER IN DIAGRAM AT LEFT DESCRIPTION DESCRIPTION

1On/Off button Powers on and off unit. LED

indicates power status.

2 Audio LIne Out Connects to speakers

3 Audio Microphone In Connects to microphone

4 (2) USB Type A connectors Connect to USB peripherals

5 12-VDC, 3-A Power In connector Connect to supplied power adapter

6DB9 connector Connects to serial console port

7 (2) USB Type A connectors Connect to USB peripherals

8 RJ-45 port Connect to network

9DisplayPort 1.2 Video connector Connect to monitor

10 (2) SFP+ connectors Dual 10G network ports

STEP 3 - Connect Power

CONNECT POWER TO TRANSMITTER

1. Locate the power supply adapter and the AC

line cord.

2. Plug the DC connector of the power supply

into the matching socket on the rear of the

transmitter.

3. Attach the AC line cord to the power supply

adapter.

CONNECT POWER TO RECEIVER

1. Locate the power supply adapter and the AC

line cord.

2. Plug the DC connector of the power supply

into the matching socket on the rear of the

receiver.

3. Attach the AC line cord to the power supply

adapter.

STEP 4 - Connect the Peripherals

CONNECT THE TRANSMITTER

1. Attach the Emerald Transmitter to the target

PC/workstation using DisplayPort and USB

Type B cables.

2. Connect the SFP+ transceiver appropriate

for the cable type and distance you are running

over the fiber to the SFP+1.

3. Connect from this transceiver to your

10G network switch or directly to a receiver.

Emerald does support direct attach SFP+,

typically this will be the most cost efficient

option for a relatively short distance (less than

22.9 feet [7 meters]).

NOTE: SFP+1 must be used as the primary

network connection on the Emerald 4K

Transmitters.

CONNECT THE RECEIVER

1. Attach the monitor, keyboard, mouse, USB

and audio devices to the Emerald Receiver.

2. Connect the SFP+ transceiver appropriate

for the fiber cable type and distance you are

running over fiber to SFP+1.

3. Connect from this transceiver to your 10G

network switch or directly to the receiver.

NOTE: SFP+1 must be used as the primary

network connection on the Emerald 4K

Receivers.

STEP 5 - Starting Up and Default Settings for IP

STARTING UP

1. Once everything is connected, press the

Power button on the front of the Emerald

Receiver.

2. The On-Screen Display (OSD) will appear on

the screen.

3. Enter the default administrator user name

and password.

4. The default network setting for the Emerald

Receiver uses a preconfigured static IP

address.

DE FAULT SETTINGS

Default Settings:

Transmitter IP Address: 192.168.1.22

Receiver IP Address: 192.168.1.21

Type: Static

Subnet Mask: 255.255.255.0

Default Gateway: 0.0.0.0

Admin username: admin

Admin password: no password, it is blank by

default

Ports Used: 3389

IMPORTANT: Do not lose the admin password

once configured; there is no way to reset or

retrieve it. The Emerald receiver has the option

to create a second administrator account as a

backup.

STEP 6 - Point-to-Point Installation for IP

POINT-TO-POINT INSTALLATION

In a point-to-point configuration, no

administrator setup of the Emerald

Transmitter or the Emerald receiver is

required. This enables you to install the

system quickly, directly out of the box. In the

point-to-point configuration, you can install

only one transmitter and receiver pair on a

subnet and both must be on the same subnet

unless a router is present in the network

to span subnets. To span across different

subnets, you will need to have admin rights to

both routers on either side of the installation

and setup port forwarding for Port 9020, 9030

and 3389 for KVM; Port 3389 for RDP for

Remote Desktop.

STEP 7 - Matrix Installation and Getting Started for IP

MATRIX INSTALLATION

In an IP installation, every Emerald transmitter

and receiver requires its own IP address.

The network setting is set to static, so the

addresses will need to be configured manually:

1. Always configure the transmitter first by

connecting the transmitter to the receiver, then

connect a keyboard, monitor, and mouse to the

receiver unit (receiver is on at this time).

2. Once the transmitter is configured, you can

now configure the receiver.

3. A transmitter out of the box must be

configured on the same subnet.

GETTING STARTED

Once the IP addresses have been configured,

each receiver will need to be configured for

users, user passwords, user access rights

and default video resolutions. You can access

these settings from the receiver’s OSD (reboot

the receiver and login as admin) and begin

configuring these parameters.

NOTE: Each receiver can support a maximum

of 32 users and a maximum of 32 targets

(virtualized or transmitter).

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Black Box Commutateur matriciel

Black Box

Black Box AVSW-VGA8X8-B Manuel utilisateur

Black Box

Black Box AVS-HDMI2-4X4-R2 Manuel utilisateur

Black Box

Black Box AC180A Manuel utilisateur

Black Box

Black Box SW540A-R3 Manuel utilisateur

Black Box

Black Box DCX1000 Manuel utilisateur

Black Box

Black Box XPT-DVI4X4 Manuel utilisateur

Black Box

Black Box VSW-DVI8x8 Manuel utilisateur

Black Box

Black Box ServSwitch ACL0404A Manuel utilisateur

Black Box

Black Box SW441A-R2 Manuel utilisateur

Black Box

Black Box EMERALD SE Manuel utilisateur

Black Box

Black Box AC1051A Manuel utilisateur

Black Box

Black Box AVS-3200-R2 Manuel utilisateur

Black Box

Black Box EMERALD SE DUAL-HEAD Manuel utilisateur

Black Box

Black Box ACX048 Manuel utilisateur

Black Box

Black Box AVS-HDMI2-4X4 Manuel utilisateur

Black Box

Black Box Boxilla Manuel utilisateur

Black Box

Black Box VSW-HDMI4X4-B Manuel utilisateur

Black Box

Black Box AVS-HDMI2-8X8-R2 Manuel utilisateur

Black Box

Black Box ServSwitch DKM FX Manuel utilisateur

Black Box

Black Box VSW-HDMI2X2-4K Manuel utilisateur

Black Box

Black Box IS290A Manuel utilisateur

Black Box

Black Box AVS1600 Manuel utilisateur

Black Box

Black Box VSDDVI Series Manuel utilisateur

Black Box

Black Box 26645 Manuel utilisateur

Manuels Commutateur matriciel populaires d'autres marques

Broadcast Tools

Broadcast Tools SS 8.2 Manuel utilisateur

Altimium

Altimium MATF32 Manuel utilisateur

ALFAtron

ALFAtron ALF-MUK44N Manuel utilisateur

Monoprice

Monoprice Blackbird 15377 Manuel utilisateur

Kramer

Kramer XL 3216VS Manuel utilisateur

PTN

PTN FMX12 Manuel utilisateur

CYP

CYP nT15GX01 Manuel utilisateur

Kramer

Kramer VP-2x2 Manuel utilisateur

Kramer

Kramer Sierra Video 6432V5xl Manuel utilisateur

TESmart

TESmart HMA0402A40 Manuel utilisateur

Octava

Octava HD4XSTPMX Manuel utilisateur

Intelix

Intelix FLX-88 Mode d'emploi

Kramer

Kramer LASSEN XL 3232S Manuel utilisateur

Roland

Roland XS-1HD Manuel utilisateur

Kramer

Kramer VS-66HDCPxl Manuel utilisateur

Atlona

Atlona AT-HDMI-22M Manuel utilisateur

Link

Link HD8X8 Manuel utilisateur

AMX

AMX AVS-OP-2020-117 Instructions et recettes