Bisek BSKS02 Manuel utilisateur
Bisek Cycle
Read Instructions Before Using Your New E-bike
BSKS02/04/05
Bisek Cycle
Specification
Motor: BAFANG high speed brushless motor
Power: 36V 250W/48V 500W
Wheel Size: 26inch
Tyre: 26inch * 4.0 width
Color: Black, Red, Yellow, White, Orange…
Bisek Cycle
NOTICE!
Before using your new E-bike the first time,
Charge 6hours for Li-ion batteries
Always recharge the battery before the power indicator shows no power.
Failure to follow these instructions voids any warranty, whether stated or implied.
Before operating your E-bike
Warning!
This product does not conform to Federal Motor Vehicles Standards and
Is not intended for operation on public streets, roads or highways. Serious injury can
result from the unsafe operations of this vehicle.
This product is not designed to be jumped. If jumped, even from the curb,
The E-bike Frame could break causing serious injury or death.
If jumped, the warranty is void.
Do not operate this product in traffic, on wet, frozen, oily or
Unpaved surfaces or under the influence of drugs and/or alcohol.
Avoid uneven surfaces, potholes, surface cracks and obstacles.
It is recommended that the rider wear leather gloves, kneepads
And leather boots. Always wear a DOT approved helmet.
Never carry passengers on your E-bike.
Check your state and local laws governing the use
of motorized vehicles in your area.
Bisek Cycle,. Co. is not responsible for your
Failure to comply with state and local ordinances
Relating to the use of the E-bike.
Failure to follow these operation instructions
can result in serious injury or death.
Congratulations on your new purchase! Our service department is dedicated to your
satisfaction with +86-519-8595-7950.
Bisek Cycle
Quick Start:
1, Charging:
Before plug in charger, please make sure that the charger’s plug can be properly
used in your area.
Examine the charger plug-in to make sure it suits your local regulation:
U.S. Standard: The United States, Canada, Japan, Brazil, Philippines, Thailand and
other countries and Taiwan
Europe Standard: France, Netherland, Denmark, Finland, Norway, Poland, Portugal,
Austria, Belgium, Hungary, Spain, Sweden and other European countries and South
Korea, Russia and other countries.
British Standard: Hong Kong and the UK, India, Pakistan, Singapore, Malaysia,
Vietnam, Indonesia, Maldives and Qatar.
Bisek Cycle
Switzerland Australia
Israel
You can charge your battery installed in bike or uninstalled. If you want to uninstall
the battery, push the key and twist anticlockwise until hear “Click”. Before take out
the battery, you may need to take out the seat post firstly, with quick release.
Move the cover on battery:
Charging: Chagring Finished:
Install the battery: please make sure that the lead rail on frame get into the slot in
battery. And make sure the battery is placed completely upon the conductive
contact on the bottom.
Bisek Cycle
2, Ready to Go:
1, Twist the key clockwise to “ON” position:
LCD display
2, Hold power ON&OFF button and you can adjust the speed with "▲" and "▼"
Bisek Cycle
Before You Ride
About this Manual
It is important for you to understand your new bicycle. By reading this manual
before you go out on your first ride, you will know how to get better performance,
comfort, and enjoyment from your new bicycle.
It is also important that your first ride on your new bicycle is taken in a controlled
environment, away from cars, obstacles, and other cyclists.
General Warning
Bicycles can be hazardous activity even under the best of circumstances. Proper
maintenance of your cycles is your responsibility as it helps reduce the risk of injury.
This manual contains many “Warnings” and “Cautions” concerning the
consequences of failure to maintain or inspect your bicycle. Many of the warning
and cautions say “you may lose control and fall.” Because any fall can result in
serious injury or even death, we do not repeat the warning of possible injury or
death whenever the risk of falling is mentioned.
A Special Note for Parents
It is a tragic fact that most bicycle accidents involve children. As a parent or guardian,
you bear the responsibility for the activities and safety of your minor child. Among
these responsibility are to make sure that the bicycle which your child is riding is
properly fitted to the child; that is in good repair and safe operating condition; that
you and your child have learned, understand and obey not only the local motor
vehicle, bicycle, and traffic laws, but also the common sense rules of safe and
responsible bicycling , As a parent, you should read this manual before letting your
child ride the bicycle. Please make sure that your child always wears and ANSI, ASTM,
SNELL approved helmet when riding.
Safety Checklist
Before you ride, it is important to carry out the following safety checks:
1. Brakes
Ensure front and rear brakes work properly
Bisek Cycle
Ensure brake shoe pads are not over worn and are correctly position
in relation of the rims .
Ensure brake control cables are lubricated, correctly adjusted and
display no obvious wear.
Ensure brake control levers are lubricated and tightly secured to the
handlebar.
2. Wheel and Tires
Ensure tires are inflated to within the recommended limit as displayed
on the tire sidewall
Ensure tires have tread and have no bulges or excessive wear.
Ensure rims run true and have no obvious wobbles or kinks.
Ensure all wheels spokes are tight and not broken.
Check that axle nuts are tight. If your bicycle is fitted with quick
release axles, make sure locking levers are correctly tensioned and in
the closed position.
3. Steering
Ensure handlebar and stem are correctly adjusted and tightened, and
allow proper steering.
Ensure that the handlebars are set correctly in relation to the forks and
direction of travel.
Check that the headset locking mechanism is properly adjusted and
tightened.
If the bicycles is fitted with handlebar end extensions, ensure they are
properly position and tightened.
4. Chain
Ensure chain is oiled, clean and runs smoothly.
Extra care is required in wet or dusty conditions.
5. Bearing
Ensure pedals are securely tightened to the cranks.
Bisek Cycle
Check headset, wheel bearings, pedals bearing and bottom bracket
bearings.
6. Cranks and Pedals
Ensure pedals are securely tightened to the cranks
Ensure cranks are secure to axle and are not bent.
7. Derailleurs
Check that front and rear mechanisms are adjusted and function
properly.
Ensure shift and brake levers are attached to the handlebar.
Ensure derailleur, shift levers and shift and brake cables are properly
lubricated.
8. Frame and Fork
Check that the frame and fork are not bent or broken
If either are bent or broken, they should be replaced.
9. Accessories
Ensure that all reflectors are properly fitted and not obscured.
Ensure all other fittings on the bike are properly and securely fastened,
and functioning.
Ensure the rider is wearing a helmet.
10. Motor Drive Assembly and Throttle
Ensure all motor drive components are correctly mounted and
functioning properly.
11. Battery Pack
Ensure the batteries are in good operation condition and kept fully
charged and properly secured and locked.
Bisek Cycle
Helmets
It is strongly advised that a properly fitting, ANSL or SNELL approved, bicycle safety
helmet be worn at all times when riding your bicycle. In addition, if you are carrying
a passenger on a child safety seat, they must also be wearing a helmet.
The correct helmet should:
-be comfortable
-be lightweight
-have good ventilation
-fit correctly
-cover forehead
Always wear a properly fitted helmet which covers the forehead when riding a
bicycle. Many states require specific safety devices. It is your responsibility to
familiarize yourself with the law of the state where you ride and to comply with all
applicable laws, including properly equipping yourself and your bikes as the law
requires. Reflectors are important safety devices which are designed as an integral
part of your bicycle. Federal regulations require every bicycle to be equipped with
front, rear, wheel, and pedal reflectors. Theses reflectors are designed to pick up and
reflect street lights and car lights in a way that helps you to be seen and recognized
as a moving bicyclist. Check reflectors and their mounting brackets regularly to make
sure they are clean, straight, unbroken and securely mounted, Have your dealer
replace damaged reflectors and straighten or tighten and that are bent or broken.
Ce manuel convient aux modèles suivants
2
Table des matières
