BioAxxis BD-1 Manuel utilisateur
http://www.BioAxxis.com
BioAxxis® BD1
1
PREFACE
Thank you for purchasing the BioAxxis® BD-1
fingerprint dead olt.
Please read the documentation carefully efore
installation & use. The manual details all
installation procedures and operation steps.
Manufacturer and/or Distri utors of the BioAxxis®
BD1 will not e responsi le for any damages caused
y incorrect installation or mishandling of the lock.
Any such damages will void manufacturer’s
warranty.
http://www.BioAxxis.com
BioAxxis® BD1
2
Ta le of Contents
Preface………………………………………………………………1
Installation Manual
1. Parts ........................................................................................ 3
2. Required Tools........................................................................ 4
3. Pre installation........................................................................ 5
3.1 Mark and bore holes on the door .................................. 5
3.2 Deadbolt Latch Selection.............................................. 9
4. Installation ............................................................................ 10
4.1 Installation of Deadbolt .............................................. 10
4.2 Installing Strike and Strike Lining Box (on the door
jamb) ................................................................................. 11
4.3 Sizing Tail Piece (to the right length)......................... 12
4.4 Installation of the Outdoor Unit.................................. 14
4.5 Installation of the Indoor Unit .................................... 16
5. Trouble Shooting .................................................................. 23
Operation Manual ..................................................................... 25
Section I Enrolling Administrators (First 2 Fingerprint
Users):............................................................................... 28
Section II Enrolling Fingerprint Users 3 thru 30:........... 33
Section III – Deleting Individual Fingerprint Users:........ 36
Section IV – Deleting ALL Fingerprint Users: ................ 39
Section V – Unlocking the BioAxxis® BD1 from outside:
.......................................................................................... 41
Section VI – Locking the BioAxxis® BD1 from Outside:
.......................................................................................... 43
Section VII – Locking and Unlocking the BioAxxis® BD1
from Inside:....................................................................... 44
USER ENROLLMENT TABLE: ..................................... 45
http://www.BioAxxis.com
BioAxxis® BD1
3
1. Parts
Please familiarize yourself with all the parts in the packaging box of
the BioAxxis® BD1. If any part is missing or damaged, contact our
service center or your local dealer.
Outdoor Unit
Indoor Unit
Strike Lining Box
Outdoor Rubber Gasket
Strike Plate
Keys
D
eadbolt Latch
2 ¾” backset (70mm)
Deadbolt Latch
2 3/8” backset (60mm)
Screws (82 mm)
http://www.BioAxxis.com
BioAxxis® BD1
4
Screws
(2 x 40 mm & 1 x 29mm)
Wooden & Metal
Screws
Alkaline
Batteries
2. Required Tools
① Electric or battery operated Drill
② One 3/8” Diameter Drill Bit
③ One 1” Diameter Drill bit
④ One 2 1/8” Diameter Drill Bit
⑤ A Carpenter Chisel
⑥ A Hammer
⑦ A pair of scissors
⑧
⑧⑧
⑧ Vise Grip
⑨ Philips & flat head screw drivers
⑩
⑩⑩
⑩
Metal Cutters or Hacksaw
11) Marker
http://www.BioAxxis.com
BioAxxis® BD1
5
3. Pre-installation
3.1 Mark and ore holes on the door
3.11 Mark holes on door
For doors with existing deadbolt lock with 2 1/8” diameter hole:
1) Remove existing cylindrical deadbolt .
2) Please be sure to use the installation
template when installing the
BioAxxis® BD1 on a door with an
existing deadbolt.
http://www.BioAxxis.com
BioAxxis® BD1
6
3) Cut out the two, 3/8” holes on the
Installation Template that correspond
to your existing backset (2 3/8” or 2
¾”).
4) Rest the installation template on the
front of the door, on top of the
existing 2 1/8” hole, making sure that
it is aligned properly for the door’s
existing 2 3/8” or 2 ¾” backset.
5) Mark the two, 3/8” holes that you cut
out of the installation template on the
door (with a magic marker).
http://www.BioAxxis.com
BioAxxis® BD1
7
6) Bore the two, 3/8” holes into the door
(using a 3/8” drill bit), making sure
that the holes fully penetrate through
the door.
7) Go to Section 4.3 in the User Manual
http://www.BioAxxis.com
BioAxxis® BD1
8
For doors that do not ha e a cylindrical deadbolt lock or a hole for
the cylindrical deadbolt lock:
A. Start approximately 46” from
floor. Select the appropriate
installation template
according to the length of the
backset. Fold and apply the
template to the edge of the
door bevel. Mark the center
point of the cylinder hole on
the door face, and then mark
the center point of the
deadbolt hole on door edge,
as indicated on the template.
B. For installation of
combination set (door handle
and deadbolt), it is
recommended that the
distance is 5 ½” between the
two center points.
C. Mark the center points of the
two small holes on the door
face for the two upper fixing
posts mounted on the top
plate of the outdoor unit, as
indicated on the installation
template.
http://www.BioAxxis.com
BioAxxis® BD1
9
3.12 Bore holes
A. Bore a 2 1/8” diameter hole in the
center of door face for chassis. (It is
recommended to bore this hole from
both sides of the door to avoid
splintering.)
B. Bore a 1” diameter hole in the center
of door edge for deadbolt.
C. Bore two separate 3/8” diameter
holes for the upper fixing posts.
3.2 Dead olt Latch Selection
There are two deadbolt latches in each box, one with a 2 3/8”
(60mm) backset and the other with a 2 ¾” (70mm) backset. Make
sure which length you will need and select the right one before
installation.
http://www.BioAxxis.com
BioAxxis® BD1
10
4. Installation
4.1 Installation of Dead olt
A.
Insert the deadbolt latch into the hole
in the edge of the door (follow the UP
sign), keeping it parallel to the face of
the door. Mark the outline of the face
plate and remove the deadbolt.
B.
Then chisel 1/8” deep rectangular
shape, per your marking (or until the
faceplate is flush with the door edge).
C.
Insert the deadbolt latch; make sure
the deadbolt UP sign is facing
upwards. Then fasten the screws.
Table des matières
