BINDTEC YL-300PM Manuel utilisateur

- 0 -

YL-300PM

USER MANUAL

- 1 -

CONTENTS

1. Overview of Safety Features and Precautions

2. Product Introduction and Accessories

3. Parts and Functions

4. Band Installation

5. Binding

6. Removing a Failed Band

7. Troubleshooting

8. Specifications

Product Warranty

- 2 -

Overview of Safety Features and Precautions

For your safety

Carefully read this user manual before operating the machine.

Maintenance requirements

1. Make sure the power is supplied and the voltage fluctuation be kept at a

minimum.

2. High temperature, high humidity, or any other environmental conditions

jam the band around the roller, rendering the unit not inoperable.

3. Please clean the unit regularly. In particular, clean the upper cover and

the roller with a brush.

4. Unit warranty is void if it has been tampered with or disassembled by

anyone other than designated service personnel.

5. Touching the heater when the unit is operational or within 10 min after

the shutdown of the machine may cause burn injuries.

6. Make sure the power is off after using the unit.

Do not lift the arch when moving the machine.

- 3 -

Product Introduction and Accessories

Automatic binding machine with press (YL-300PM)

* The compactness and ease of installation make the unit efficient to use.

* It is Korea's first press binding machine.

*It performs fast binding time with belt-driven compression.

* It uses a 20 mm film band.

*It takes about 18 sec to warm up.

* It binds without odor.

Accessories

1. Manual .............................................................. 1 pc

2. Film band ......................................................... 1 roll

3. Guide ................................................................ 1 set

4. Power cable .................................................... 1 pc

5. Brush .............................................................. 1 pc

- 4 -

Parts and Functions

Arch

2. Start Button

3. Feed/Reset Button

4. Press/Reverse Button

5. Item Sensor

Band Reel Cover

6.Temperature

Control Knob

Front Cover

1. Power Switch

Idle Roller

Main Roller

Spacer

- 5 -

1. Power Switch

It turns the power ON or OFF.

2. Start Button

The Start Button’s LED blinks when the band is supplied to the rail, and the

object is placed in the correct position. At this point, press the button to start the

binding.

3. Feed/Reset Button

The Feed Button’s LED blinks if the band is not supplied to the rail. To supply

the band, press the Feed Button to rotate the main roller forward.

Reset: Press and hold the Feed Button for about 1.2 sec to loosen the gap

between the main and idle rollers, and adjust the band input. Furthermore,

perform this function to remove the band in case it is jammed. Then, press the

button again to return to its initial state.

4. Press/Reverse Button

When the power is on, the LED on the Press Button turns on and the unit is set

to press binding mode.

Press the Press Button to turn the press on or off.

Reverse: Press the Press Button for about 1.2 sec to let the main roller turn in

reverse, allowing the attached band to be removed.

5. Item Sensor

The Item Sensor’s LED blinks when the item to be bound is in place.

6. Temperature Control Knob

This knob is used to adjust the heater’s temperature, whereas

turning the knob clockwise increases the temperature.

- 6 -

Band Installation

1. Asses the band’s condition

If the cutting surface is not straight, the band is crumpled, or foreign matter is

found, remove the portion using scissors. Poor band conditions can lead to

jamming.

2. Open the front cover and band reel cover.

3. Orient the band in a counterclockwise position,

as shown in the photo.

4. Press the Feed Button for about 1.2 sec

to widen the gap between the main and idle rollers.

5. Slide the band between the main and idle rollers.

The band’s edge must pass between the main roller and the idle roller for about

2–4 cm. Furthermore, be careful not to operate the band if it is caught between

the idle roller and the guide.

6. Press the Feed Button shortly to install the band.

7. Close the band reel cover and front cover.

8. A quick press of the Feed Button rotates the main roller, and subsequently,

the band is supplied. If the feed motor rotates and the band is correctly installed,

the Feed Button’s LED turns on from blinking.

- If the edge of the band is damaged, setting the band may fail. Fix the

edge by cutting off the damaged portion.

- Be sure to close the band reel cover.

- Be careful with foreign substances at the beginning and end of the

band. These may cause jamming and damage to the machine.

Caution

main roller

guide

- 7 -

Binding

1. Turn the power on.

2. Check if the Start Button and Feed Button’s LEDs

are on.

3. To bind without using the press,

press the Press Button and wait for the LED to turn off.

4. Place the objects on the item sensor,

and press the Start Button.

5. Once the binding is complete, unload the objects.

6. Check the band’s adhesion and adjust the

temperature if necessary with the temperature control knob.

Be careful not to touch the press or band during operation.

Removing a Failed Band

How to fix a band that is jammed or has deviated from the rail

1. Open the front cover and the band reel cover.

2. Using scissors, vertically cut the band that has clustered on each side of the

main roller.

3. Press the Feed Button for about 1.2 sec to widen the gap between the main

and idle rollers.

Remove the shredded band by pulling it, as horizontally as possible, in the

reverse direction of the main roller.

4. Remove any band pieces from the rails.

5. Supply the band by following step no. 5of 4. Band Installation.

In case of a jam or the rail departure of the band, quickly pressing the

Feed Button will cause the band to be wrapped around the main roller, making it

difficult to remove the band. Thus, it is important to carefully follow the steps above.

①Power

switch

Spa

cer

Tape unrill

direction

Caution

Power Switch

Feed/Reset

Start

Press/Reverse

- 8 -

When the band is entangled on the spacer

1. Turn off the power.

2. Cut off the upper portion of the band that is nearest

the spacer, as shown in the photo.

3. Pull out the remaining part of the band, as shown in the photo.

4. Turn on the power.

Troubleshooting

Follow the steps below when experiencing issues with the machine’s

operation.

1. If the Start Button’s LED is OFF

* Check if the power plug is connected.

* Check if the power switch is turned on.

→Insert the power plug and turn on the power switch.

2. If the Feed Button’s LED is blinking

* Check if the band is supplied.

* Check if the band is supplied to the spacer.

→Refer to 4. Band Installation when supplying the band.

3. The machine cannot cut the band.

→The cutter’s service life has expired. Seek a replacement from A/S.

4. Weak adhesion

* Check the heater’s temperature if it is too low.

→Adjust the heater’s temperature using the control knob.

5. The adhesive part of the band is burnt or smells of smoke.

→The temperature is too high, so lower the temperature.

spacer

- 9 -

Specifications

Speed

10 cycles/min

Binding Size

240(W) ×220(H) mm

Power Supply

AC110/220 V, 50/60 Hz

Power Consumption

250 W

Tension

About 4–5 kg

Press Pressure

About 18 kg

Band Width

Film band 20 mm

Product Size

487(W) x 274(D) x 593(H) cm

Weight

36 kg

Autres manuels pour YL-300PM

Table des matières

Autres manuels BINDTEC Compteur de billets de banque

BINDTEC

BINDTEC YL-300PM Manuel utilisateur

Manuels Compteur de billets de banque populaires d'autres marques

BellCon

BellCon BellCount S515 Manuel utilisateur

Orbit Research

Orbit Research iBill Manuel utilisateur

Grace Technology

Grace Technology GV-870 Manuel utilisateur

Safescan

Safescan 2265 Manuel utilisateur

Ribao

Ribao BC-30 Manuel utilisateur

Mixed Bills

Mixed Bills DG 1000 Manuel utilisateur

Safescan

Safescan 2660-S Manuel utilisateur

PRO Intellect Technology

PRO Intellect Technology PRO 95U Manuel utilisateur

Dors

Dors 600 Manuel utilisateur

radiotec

radiotec rapidcount S 575 Manuel utilisateur

CUMMINS ALLISON

CUMMINS ALLISON JetScan Manuel utilisateur

PRO Intellect Technology

PRO Intellect Technology 40 NEO Manuel utilisateur

Conrad

Conrad 75 17 78 Manuel utilisateur

Total

Total M2300U Manuel de formation

Double Power Electronics

Double Power Electronics DP-8120VB Manuel utilisateur

ratiotec

ratiotec Soldi Smart Plus Manuel d'utilisation et d'entretien

Olympia

Olympia NC 455 Manuel utilisateur

Plaisio

Plaisio Q-CONNECT QCD11 Manuel utilisateur