Bin Master WR-30 Series Manuel utilisateur

WR-30 & WR-90 Repeater Field Unit

Instruction Manual

Division of Garner Industries

7201 North 98th Street

Lincoln, NE 68507-9741

(402) 434-9102

Wireless System

• Wireless Repeater Unit in a Rugged, Industrial Housing

• Simple to Order, Configure, & Install

• Increase Range an Additional 1 Mile Line-of-Sight, 500 Ft Indoor

• Remote or Attached Antenna

• Flanges for Wall or Pipe Mounting

• Software Available for Even Easier Setup

• Rugged, IP68, NEMA 4X Enclosure

Wireless Repeater Field Unit Instruction Manual

Disclaimer

The information contained in this document is subject to change without notice. BinMaster

makes no representations or warranties with respect to the contents hereof and specifically

disclaims any implied warranties of merchantability or fitness for a particular purpose.

Caution: Read complete

instructions prior to installation and

operation of the device.

Warning: Risk of electric shock or

personal injury.

Warning!

• This product is not recommended for life support

applications or applications where malfunctioning

could result in personal injury or property loss.

Anyone using this product for such applications does

so at their own risk. BinMaster shall not be held liable

for damages resulting from such improper use.

• Failure to follow installation guidelines could result in

death or serious injury. Make sure only qualified

personnel perform the installation.

Limited Warranty

BinMaster warrants this product against defects in material or workmanship for the specified

period under “Specifications” from the date of shipment from the factory. BinMaster’s liability

under this limited warranty shall not exceed the purchase value, repair, or replacement of

the defective unit.

Registered Trademarks

Modbus® is a registered trademark of Schneider Electric. All other trademarks mentioned in

this document are the property of their respective owners.

www.binmaster.com

Wireless Repeater Field Unit Instruction Manual

Table of Contents

Table of Contents ......................................................................................................................................... 3!

Table of Figures ........................................................................................................................................... 3!

Introduction ................................................................................................................................................... 4!

Ordering Information .................................................................................................................................... 4!

Specifications ............................................................................................................................................... 5!

General ..................................................................................................................................................... 5!

Wireless Radio .......................................................................................................................................... 5!

WR Manager Software ............................................................................................................................. 5!

Safety Information ........................................................................................................................................ 6!

Installation .................................................................................................................................................... 6!

Unpacking ................................................................................................................................................. 6!

Pre-Installed Conduit Plug ........................................................................................................................ 7!

Mounting Instructions ................................................................................................................................ 7!

Cover Jam Screw...................................................................................................................................... 7!

FCC Notice ............................................................................................................................................... 7!

IMPORTANT ......................................................................................................................................... 7!

Canada (IC) Notice ............................................................................................................................... 7!

Connections .............................................................................................................................................. 8!

Power Connector .................................................................................................................................. 8!

Setup and Programming .............................................................................................................................. 9!

Overview ................................................................................................................................................... 9!

Programming Buttons ............................................................................................................................... 9!

WR Manager Software ........................................................................................................................... 10!

Setup Menu ............................................................................................................................................ 11!

Entering Numeric Values .................................................................................................................... 11!

Network ID ........................................................................................................................................... 11!

Password Setup .................................................................................................................................. 12!

Restore Defaults ................................................................................................................................. 12!

Programming with WR Manager ............................................................................................................. 13!

Mounting Dimensions ................................................................................................................................. 15!

PDA6963-BM Stainless Steel Pipe Mounting Kit ....................................................................................... 15!

Table of Figures

Figure 1. WR-30 Device Assembly, Rear View ............................................................................................ 8!

Figure 2. Power Connections ....................................................................................................................... 8!

Figure 3. Enclosure Dimensions – Front View ........................................................................................... 15!

Figure 4. Enclosure Dimensions – Side Cross Section View ..................................................................... 15!

Figure 5. PDA6963-BM Stainless Steel Pipe Mounting Kit ....................................................................... 15!

Wireless Repeater Field Unit Instruction Manual

Introduction

BinMaster WR-30-RP wireless signal repeaters are used to retransmit wireless signals when

connectivity between WR-30 or WR-90 wireless units is an issue. They are incredibly simple to

install as they only require power and a network ID. Any units in range of the repeater with the

same network ID will retransmit through it, thus increasing signal strength. Use repeaters to

broadcast over very long distances or around permanent obstacles.

Ordering Information

Standard Model

Model

Description

WR-30-RP

Wireless Repeater Field Unit

Accessories

Model

Description

PDA3120-N-BM

RP-SMA F to N Male Antenna Cable 20ft

PDA3140-N-BM

RP-SMA F to N Male Antenna Cable 40ft

PDA3120-S-BM

RP-SMA M/F Antenna Cable 20ft

PDA3140-S-BM

RP-SMA M/F Antenna Cable 40ft

PDA3900-12-N-BM

WR-90 MHz Antenna, 1/2" NPT

PDA3900-6Y-N-BM

Yagi Antenna 6dB

PDA3900-9Y-N-BM

Yagi Antenna 9dB

PDA6963-BM

Stainless Steel WR-30 Mounting Kit

Wireless Repeater Field Unit Instruction Manual

Specifications

Except where noted all specifications apply to operation at +25°C.

General

Display

32-character dual-line alphanumeric

dot matrix LCD display with backlight

(4.68mm x 2.21mm characters)

Display

Orientation

Display may be mounted at 180°

from default orientation

Network ID

Field selectable: 0 - 99

Programming

Methods

Four programming buttons (behind

glass) or PC with WR Manager

software.

Password

A programmable password restricts

modification of programmed settings.

Power

12-28 VDC, 5 W max

Non-Volatile

Memory

All programmed settings are stored

in non-volatile memory for a

minimum of ten years if power is lost.

Isolation

500 V

Environmental

Operating temperature range:

-40 to 65°C (display inoperable

< -20 °C); Storage temperature

range: -40 to 85°C; Relative

humidity: 0 to 90% non-condensing

Connections

Removable screw terminal blocks

accept 16 to 30 AWG wire.

Enclosure

Cast aluminum with glass window,

0.30% max copper content, corrosion

resistant powder coating, color: blue.

NEMA 4X/IP68. Two ½" NPT

threaded conduit openings. One ½"

NPT stainless steel conduit plug with

10 mm hex key fitting installed.

Mounting

May be mounted directly to conduit.

Two mounting holes for 1.5" pipe or

wall mounting. See Mounting

Dimensions on page 15 for mounting

space requirements.

Tightening

Torque

2.5 lb-in (0.28 Nm)

Shipping

Dimensions

17" x 14" x 9" (43.2 cm x 35.6 cm x

22.9 cm) (L x W X H)

Shipping

Weight

5 lbs. (2.27 kg)

Warranty

3 years parts & labor

Wireless Radio

Frequency

900 MHz

Range

500 ft (152.4 m) indoor, 1 mi (1.61

km) outdoor (line-of-sight)

Encryption

AES 128-bit encryption available

using WR Manager software

Interference

Reduction

Frequency Hopping Spread

Spectrum (FHSS)

Power Output

24 dBm (250 mW)

Sensitivity

-101 dBm

WR Manager Software

System

Requirements

Microsoft® Windows® XP/Vista/7/8/10

Communicatio

USB 2.0 (Standard USB A to Micro

USB B)

Configuration

Configure devices one at a time

Wireless Repeater Field Unit Instruction Manual

Safety Information

Caution: Read complete instructions

prior to installation and operation of the

device.

Warning: Read all product labels

completely and follow all instructions

and requirements listed on the labels

for installation or service.

Warning!

Installation and service should be performed only by trained

service personnel. Service requiring replacement of internal

components must be performed at the factory.

Installation

All pushbuttons and wiring connectors are accessed by opening the enclosure. To access

electrical connectors, remove the 2 captive screws and remove the display assembly.

Pushbuttons may also be accessed using the magnet assembly if reed switches are installed.

Unpacking

Remove both units from box. Inspect the packaging and contents for damage. Report damages, if

any, to the carrier. If any part is missing or the unit malfunctions, please contact your supplier or

the factory for assistance.

Wireless Repeater Field Unit Instruction Manual

Pre-Installed Conduit Plug

The WR-30-RP is supplied with one pre-installed optional conduit plug for installations that do not require

the use of both conduit entries. The conduit plug includes an internal hexagonal socket recess for

removal.

Mounting Instructions

The WR-30-RP has two mounting holes that may be used for a 1.5” pipe mounting or wall mounting.

Alternatively, the unit may be supported by the conduit using the conduit holes provided.

It can also be mounted by using the PDA6963-BM mounting bracket in order to orient the device antenna

away from the pipe. Refer to Mounting Dimensions on page 15 for details on wall or panel space

requirements.

Cover Jam Screw

The cover jam screw should be properly installed once the unit has been wired and tested in a safe

environment. The cover jam screw is intended to prevent the removal of the device cover while in

operation without the use of tools. Using a M2 hex wrench, turn the screw clockwise until the screw

contacts the device. Turn the screw an additional 1/4 to 1/2 turn to secure the cover.

Caution: Excess torque may damage the threads and/or wrench.

FCC Notice!

Contains FCC ID: MCQ-XB900HP

The enclosed device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (i.) this device may not cause harmful interference and (ii.) this device must accept any

interference received, including interference that may cause undesired operation.

IMPORTANT

The RF module has been certified for remote and base radio applications. If the module will be used for

portable applications, the device must undergo SAR testing. This equipment has been tested and found

to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the interference

by one or more of the following measures: Re-orient or relocate the receiving antenna, Increase the

separation between the equipment and receiver. Connect equipment and receiver to outlets on different

circuits, or consult the dealer or an experienced radio/TV technician for help.

Canada (IC) Notice

Contains Model: XB900HP, IC: 1846A-XB900HP

Integrator is responsible for its product to comply with IC ICES-003 & FCC Part 15, Sub. B - Unintentional

Radiators. ICES-003 is the same as FCC Part 15 Sub. B and Industry Canada accepts FCC test report or

CISPR 22 test report for compliance with ICES-003.

Wireless Repeater Field Unit Instruction Manual

Connections

To access the power connector, remove the enclosure cover and unscrew the two captive stainless steel

screws. Remove the electronics assembly from the enclosure. The power connection is made to a two-

terminal removable connector on the back of the assembly. Grounding connections are made to the two

ground screws provided on the base – one internal and one external.

Warning!

• Static electricity can damage sensitive components.

• Observe safe handling precautions for static-sensitive components.

• Use proper grounding procedures/codes.

• Observe all safety regulations. Electrical wiring should be performed in

accordance with all agency requirements and applicable national, state, and

local codes to prevent damage to the device and ensure personnel safety.

Figure 1 below shows the locations of screw terminal blocks on the rear of the wireless unit assembly.

Note: Digital I/O, Modbus, and Signal connections are not used with the repeater unit.

Figure 1. WR-30 Device Assembly, Rear View

Power Connector

Power connections are made to a two-terminal connector

labeled POWER in Figure 1. The WR-30 is reverse polarity

protected; it will not be damaged if wired backward.

Make sure that the power supply can provide between 12 and

28 VDC to the wireless device.

Wireless

Module

Figure 2. Power Connections

Wireless Repeater Field Unit Instruction Manual

Setup and Programming

Overview

Setup and programming is done through the programming buttons located underneath the enclosure

cover. After power connection has been completed and verified, apply power to the device.

Programming Buttons

The units can be programmed using the buttons located behind the enclosure cover. Use the menu

button to enter or exit programming mode, the next button to cycle forward through menu options, the

previous button to cycle backward through menu options, and the enter button to select the menu item or

option you want.

During number entry, use the next button to select a digit and the previous button to increment the

selected digit.

Press the display button while in run mode to show the current analog and digital inputs and outputs.

Button

Description

Display

Status

Enter or exit the

device menu

RSSI

Received Signal Strength Indicator

Indicates the wireless signal strength

between wireless devices on a scale of 1

to 10. If the repeater is used in a WR-90

installation, this value represents the

signal strength between the base station

and the repeater. If the repeater is used

in a WR-30 installation, this value

represents the signal strength between

the primary unit and the repeater.

Enter

Select a menu item

of option

Cycle backward

through menus or

increment digit

Receiving/Transmitting

Flashes while the devices are sending

and/or receiving data

Cycle forward

through menus or

select next digit

REP

Repeater

Indicates that the device is a repeater

unit. This distinction is fixed and cannot

be changed.

Wireless Repeater Field Unit Instruction Manual

WR Manager Software

The unit can also be programmed using the PC based WR Manager. Units connect to a PC via the micro

USB connection on their face, underneath the enclosure cover.

Use of WR Manager is required for programming advanced settings such as wireless encryption.

Note: Units must be powered externally prior to programming via USB.

WR Manager is available on the included CD.

Instructions on the use of WR Manager to program the WR-30 wireless units can be found under

Programming with WR Manager on page 13.

Autres manuels pour WR-30 Series

Ce manuel convient aux modèles suivants

Table des matières

Manuels Répétiteur populaires d'autres marques

Gigaset

Gigaset 108 Manuel utilisateur

Ace TECHNOLOGY

Ace TECHNOLOGY USR-1900A Manuel utilisateur

Kenwood

Kenwood TKR-750-850 Manuel de la liste des pièces

Asus

Asus RP-AC51 Manuel utilisateur

Exibel

Exibel HRP0101 Manuel utilisateur

Kidde

Kidde Vega Manuel utilisateur

Telcosat

Telcosat RBB 850 Guide d'installation

York

York Universal LINC485 Manuel utilisateur

MIKOM

MIKOM MRx01B Power Series Manuel utilisateur

Simrad

Simrad RD 301 Manuel utilisateur

Tait

Tait TB7304 Manuel utilisateur

R-tron

R-tron RSN-CDMA-37-C Manuel utilisateur

Inventronics

Inventronics DALI REPEATER SO Manuel utilisateur

XFP

XFP 16 Manuel utilisateur

Andrew

Andrew MRx18 Manuel utilisateur

COMBA

COMBA RXA3748 Manuel utilisateur

ADRF

ADRF SDR-ICS-43 Manuel utilisateur

Teltonika

Teltonika WRP100 Manuel utilisateur