Bigassfans OBSIDIAN BACF15120B Manuel utilisateur

–

MODELS

VOLTAGE

TOTAL POWER (W)

CURRENT(AMPS)

BACF15120B

120

1500

12.5

FIRE/EXPLOSION HAZARD WARNING

NOT FOR USE IN HAZARDOUS OR EXPLOSIVE ATMOSPHERES

During operation, always ensure combustible materials are kept at a safe distance from the heater

body and from the emitted radiant energy. This heater is not intended for use in hazardous areas where

flammable vapours, gases, liquids or other combustibles are present. Failure to do so can result in

personal injury/or property damage.

FOR INDOOR AND OUTDOOR COMMERCIAL AND RESIDENTIAL USE

BIG ASS FANS dba DELTA T LLC 238 INNOVATION DR. LEXINGTON KY 405011 PHONE: 877.BIG.FANS

TABLE OF CONTENTS

1 - SAFETY............................................................................................................................................................. 3

2 - INSTALLATION INSTRUCTIONS ........................................................................................................................ 5

3 OPERATING INSTRUCTIONS............................................................................................................................... 7

2.6.1 Operation of the Remote Control ......................................................................................................8

4 MAINTENANCE .................................................................................................................................................. 9

5 GROUNDING INSTRUCTIONS........................................................................................................................... 12

WARNINGS

THIS ELECTRIC APPLIANCE PRODUCES INFRARED HEAT, AND FAILURE TO FOLLOW

WARNINGS AND INSTRUCTIONS CAN CAUSE FIRE, ELECTRIC SHOCK, OR INJURY.

Heater must be installed by a certified electrician and installation must

adhere to all local, state and national electric codes.

READ AND SAVE THESE INSTRUCTIONS

Please read this owner’s manual carefully before using the unit and keep the manual for future reference.

USE THIS HEATER ONLY AS DESCRIBED IN THIS MANUAL. ANY OTHER USE NOT RECOMMENDED BY THE

MANUFACTURER MAY CAUSE FIRE, ELECTRIC SHOCK OR INJURY TO PERSONS

Notice: Changes or modifications not approved by the party responsible for compliance will void the user's

authority to operate the equipment.

IMPORTANT INSTRUCTIONS

When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric

shock, and injury to persons, including the following outlined in section 1 –SAFETY. Read all instructions before installing or

using this heater.

1- SAFETY

WARNINGS

WARNING: FIRE OR EXPLOSTION HAZARD

•Failure to precisely follow safety warnings could

result in serious injury or property damage.

•Heater has hot surfaces and arcing or sparking

parts inside. Do not use the heater in areas where

gasoline, paint or flammable vapors or liquids are

used or stored.

•Heater is not to be installed or used in an area

containing hazardous or flammable materials

including but not limited to rags, fabrics, spray or

aerosol cans, cleaning compounds, plastic

containers, paper products, organic dusts,

straw/hay, gasoline, kerosene, lighter fluid, etc.

•To prevent a possible fire, do not block air intakes

or exhaust in any manner.

•Do not insert or allow foreign objects to enter any

ventilation or exhaust opening as this may cause

an electric shock or fire, or damage to the Heater.

Do not cover the heater in any manner, do not

hang clothing on or near the heater.

•Caution! Do not use the heater together with

another appliance connected to the same supply

line or connected to the same breaker.

•Use the heater with a properly grounded three

prong plug.

•The power cord must not be left on or around the

heater body.

•Keep combustible materials, such as furniture,

pillows, bedding, papers, clothes, curtains, etc. at

least 6 feet (1.8m) from the front of the heater

and keep them away from sides and rear.

WARNING: PERSONAL INJURY HAZARD - OPERATION

•This heater is hot when in use. To avoid burns, do

not let bare skin touch hot surfaces.

•Use this heater only as described in this manual.

Any other use not recommended by the

manufacturer may cause fire, electric shock, or

injury to persons.

•Extreme caution is necessary when any heater is

used by or near children or invalids and whenever

the heater is left operating and unattended.

•Never leave the heater unattended while it is

operating.

•Do not use the heater without the aluminium

grille in place.

•Do not operate any heater after it malfunctions.

Disconnect power at service panel and have

heater inspected by an electrician before reusing.

•Do not use the heater to light cigarettes or similar

materials.

•Do not insert objects in heater openings.

Electrical shock could result.

•Connect to properly grounded outlets only. To

disconnect heater, turn controls to off, and turn

off power to the heater circuit at the main

disconnect panel.

WARNING: PERSONAL INJURY HAZARD - CLEANING AND MAINTENANCE

•To avoid property damage, personal injury

or death due to electrical shock DO NOT

service the unit without turning the unit

OFF and disconnecting the heater from the

main power supply.

•Before cleaning the unit or replacing the

emitter, turn off the main power. Make sure

the heater and/or the emitter is cool before

handling.

•Service must be performed only by a

qualified service technician.

WARNING: INSTALLATION

•This product must be installed by a certified

electrician and must adhere to all local,

state and national electric codes (NEC)

•Do not direct the radiant part of the heater

towards the ceiling.

•Specified minimum clearances from front,

sides, bottom and back of unit must be met.

Failure to meet clearance minimums can

result in fire.

•Heater is not for use in bathrooms, laundry

areas or other locations where unit could fall

into water.

•Do not use the heater if it has been dropped

or damaged in any way. Ensure the emitter is

not cracked or chipped visually. Contact an

authorized BIG ASS FANS dealer for support.

•Do not use the heater if the power cord is

damaged. Contact an authorized servicer or

qualified electrician to replace the cord prior

to use.

•Unplug the appliance when it is not in use for

long periods of time, or for cleaning and

maintenance.

•Use this heater only as described in this

manual. Any other use not recommended by

the manufacturer may cause fire, electric

shock, or injury to persons.

•Heater is not to be recessed

•The heater must be installed at level on a

ﬂat, stable surface, rigid enough to safely

withstand the weight of the heater and the

heater must not be covered by any flexible

material, such as carpets, plastic or fabric.

SAVE THESE INSTRUCTIONS

2- INSTALLATION INSTRUCTIONS

Heater installation must be carried out by qualified personnel in compliance with local National Codes

(NEC) as well as any other applicable standards. Failure to comply with applicable requirements could

result in personal injury and/or property damage. Wiring procedures and connections shall be made in

accordance with national and local electrical codes having jurisdiction.

BIG ASS FANS infrared heaters produce radiant heat that warms people and objects, rather than the air around

them. The heater can be wall mounted and includes brackets which allow the user to direct the infrared heat

where desired.

To reduce the risk of fire, do not store or use gasoline or other flammable vapors and liquids in the vicinity of

the heater.

2.1 INSTALLATION CLEARANCE DISTANCES

DANGER FIRE HAZARD

The minimum clearances indicated on the nameplate and in the user manual must be observed at the time of

installation.

CAUTION: High temperatures are present, risk of fire! Keep electrical cords, drapery, furnishings and other

combustibles at least 6 feet (1.8m) from the front of the heater and away from the sides and rear.

Minimum Clearance Distances

Floor

Ceiling

Adjacent walls

6’7” (2 m)

1’ (30 cm)

18” (45 cm)

Wall Mount Minimum Clearances

2.2 ELECTRICAL INSTALLATION

Safety Precautions

1. Each power supply circuit must be properly grounded.

2. Use a certified ground fault protection device for wet environment installations.

3. Use a proper electrical connection box

4. Supply voltage and frequency must correspond to the electrical rating indicated on unit’s information

plate

2.3 WALL-MOUNTED INSTALLATION

1. Take the heater out of the box and remove all

protective foam inserts.

2. Select the installation location on the wall by

identifying the studs or structural beams that will

allow the heater to be securely attached.

WARNING: Ensure minimum clearances outlined in

section 2.1 are met.

3. Securely fasten the L-shaped brackets to the

mounting surface using both fixing holes in the

short part of the bracket. NOTE: Wall bolts or

anchors are not supplied. Select an appropriate

size to provide adequate support for the weight

of the unit and taking into consideration any

wind load conditions.

CAUTION: If there is any question regarding

security of the bolts and fixtures, contact a

professional contractor.

4. Mount the heater to the brackets with the

terminal box at the right side of the heater.

5. Adjust the heater to the desired directional

angle, then fix in this position by tightening the

fixing bolts on the brackets at the back of the

heater.

6. Secure the electrical supply cable so it does not

contact the heater body or obstruct the air vents.

Follow local and national electrical code

requirements.

The angles of attachment are 20° to 70°,

measured from the mounting wall.

2.4 ADJUSTING DIRECTIONAL POSITIONING

WARNING

Never attempt to move or adjust the heater angle while it is running. Personal

injury could result.

1. Turn off the heaters electrical supply line from the main power supply.

2. Allow the heater to cool before adjusting the angle.

3. Loosen the fixing bolts on the brackets at the back of the heater; adjust the heater as desired, then re-

tighten the fixing bolts.

Notice :The unit produces radiant heat that warms people and objects rather than the air around them. Install

the heater at an angle which points the reflector at the target space. Do not point the heater at windows or vacant

spaces, as the heat will not be delivered to the occupants.

3OPERATING INSTRUCTIONS

Caution! The heater must be properly installed before it is used.

Caution! When the heater is not in use for extended periods of time, be sure to set the operating mode to the

"OFF" position.

The heater has two modes of operation, these two modes can be selected using the button on the right side of

the heater.

PCB bypass Mode

Remote Mode

OFF

INCORRECT

CORRECT

3.1 PCB BYPASS MODE

When the bypass mode is selected, the heater will operate at 100% of rated power OR may be controlled by

other type of external control system. Installer or specifier is responsible for compatibility and safety of controls

not included with this heater.

3.2 REMOTE MODE

The remote control must be pointed in the direction of the receiver on the heater body (located on the front

face) and must be used within a maximum distance of 6 m.

In remote mode the heater has 6 power levels. The power level can be selected with the remote. The selected

power level is displayed on the screen on front of the heater. The remote mode only works with the remote

control supplied with the product. L0 represents standby while L6 represents the maximum heating level.

3.2.1 OPERATION OF THE REMOTE CONTROL

Symbol

Description

Up one heating level

MAX

The heater goes directly to the highest heating level (short

delay on start).

Down one heating level.

To switch the heater ON: Press On.

The heater has a soft start function using only 16% of

maximum power. 4 seconds after the heater has been turned

on, it will automatically switch to the last heating level used.

In case of the first-time use, after 4 seconds the heater will

automatically switch to 100% power.

OFF

To switch the heater OFF: Press OFF. The heater will switch to

Standby mode (the receiver indicator will light up).

Notice:

Display

Description

Power setting

Heating level 1

33%

Heating level 2

50%

Heating level 3

66%

Heating level 4

80%

Heating level 5

88%

Heating level 6

100%

Standby

1. Use 2 pieces AAA, 1.5V batteries (not included) in the remote control. Remove the batteries when not in use for an

extended period of time to increase battery life.

2. The heater can be still used normally in the event the remote control is misplaced, however it must be used in PCB

bypass mode where the heater will run fully on. Contact your local authorized BIG ASS FANS Dealer for remote

replacement.

3. The remote-control function may not work if there is a barrier between the remote control and heater.

4. Replace the batteries as required to ensure correct remote functionality.

4MAINTENANCE

WARNINGS

1. Allow the heater and the emitter to cool down before handling.

2. Installation and maintenance must be performed by a qualified technician.

3. Turn oﬀ the power before beginning maintenance.

4. Do not attempt to service or repair the unit while it is running.

5. Should the heater be dropped or damaged or malfunction at any time, immediately turn oﬀ the main

power source and do not use it until it has been examined by an authorized service facility.

Notice: Do not touch the emitter with bare hands. Wearing soft cotton gloves is highly recommended. Finger

prints will burn into the carbon emitter during use and cause premature heater failure. If the emitter is

anidvertently touched, or if it needs to be cleaned, carrefully wipe it using rubbing alcohol or methylated spirits.

4.1 CLEANING

To keep the heater running at peak performance and prevent premature failure, the emitter lamp and reflector

should be cleaned as required. Buildup of dust on these components will accelerate aging. In seaside

environments, salt spray may collect on these components. Salt spray should be removed regularly.

To clean the reflector or emitter lamp, follow these steps:

1. Turn the power to «OFF» and disconnect the heater from the main power supply.

2. Remove screws from the left side cover and slide the perforated front grille out of the heater body.

3. Carefully wipe the reflector with a soft, lint-free cloth.

4. After cleaning, be sure to properly reinstall the heater grille.

4.2 REPLACING THE EMITTER

Contact your distributor for the correct replacement emitter, providing the model number and rating from the

rating label. Using an incorrect replacement emitter can cause the heater to fail.

Notice: Read through the Emitter replacement procedure below before beginning the replacement. For easier

replacement, remove the heater from the wall or ceiling.

1. WARNING! TURN OFF THE POWER AND

DISCONNECT THE HEATER FROM THE MAIN

POWER SUPPLY. FAILURE TO DISCONNECT

HEATER BEFORE REPLACING THE EMITTER

COULD CAUSE ELECTRIC SHOCK OR DEATH!

2. Be sure the heater and the emitter are cool:

burns can result from touching hot

components.

3. Remove screws from the left side of the heater

fixture and remove the aluminum end cap.

(keep these parts).

4. Carefully slide the protective grille out of the

heater body to expose the emitter and the

plastic sealing connectors.

5. Carefully unscrew the protective plastic cap

and carefully slide the cap back cap to expose

the wire/ metal connector system.

Caution! Disconnect the metal locking

connectors by squeezing the metal tab.

6. Bend the metal tabs to remove the small

reflector shield sheet metal parts. Hold on to

these pieces. This will allow you to slide the

emitter into a bigger cavity to remove it from

the reflector and heater body. Properly dispose

of the broken emitter at your local recycling

center.

7. Hold the new emitter by the ceramic ends or

wear clean dry gloves to prevent and position

the new lamp inside the unit.

Ceramic Infrared Emitter End

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Bigassfans Chauffage de terrasse

Bigassfans

Bigassfans Obsidian BAFCF30240B Manuel utilisateur

Manuels Chauffage de terrasse populaires d'autres marques

empasa

empasa HMXD-E-NHS Manuel utilisateur

Sunred

Sunred Indus Manuel utilisateur

HEAT1

HEAT1 ECO pro-line 2300W Manuel utilisateur

Heatmaxx

Heatmaxx SRPH98 Manuel utilisateur

Sunjoy

Sunjoy A30600640 Manuel utilisateur

Event Furniture

Event Furniture 16091 Guide de dépannage

Prem-I-Air

Prem-I-Air EH1462 Manuel utilisateur

Blumfeldt

Blumfeldt 10028637 Manuel utilisateur

Sunjoy

Sunjoy L-PH011PSS-2 Manuel utilisateur

Melissa

Melissa 670-202 Manuel utilisateur

Quality Heating

Quality Heating THE-12DW Manuel utilisateur

DCS

DCS PHFS-P4 Guide d'installation

EUROM

EUROM 334241 Manuel utilisateur

Lava Heat

Lava Heat Venetian Manuel utilisateur

EHS Ltd.

EHS Ltd. HQH-2000W Manuel utilisateur

VONROC

VONROC ALICUDI PH515AC Manuel utilisateur

OZONA

OZONA Heatflow IF010997 Manuel d'exploitation et d'entretien

theBBQshop

theBBQshop 51611010 Guide de configuration