Biamp Desono C-IC6 Instructions d'utilisation d'origine
A: 9300 S.W. Gemini Drive Beaverton, OR 97008 USA T: +1 503.641.7287 W: www.biamp.com
JUNE 2019
Product Description
The desono™ C-IC6 is a low-profile, two-way passive coaxial loudspeaker
optimized for speech and music reproduction in conferencing applications.
The C-IC6 may be used with traditional amplifiers, and also directly integrates
with the Tesira® AMP-450BP: a four-channel “backpack” PoE+ amplier that
attaches directly to the C-IC6.
Setup and Use
The Tesira software provides an intuitive interface for setup and programming
of the AMP-450BP. The information supplied by this manual relates to physical
connections and device setup. For more details on software setup, please
consult the Tesira Help File.
The C-IC6 conferencing loudspeaker is equipped with a bridge-mounted
165mm, treated paper low-frequency woofer, a separate 25mm soft-dome
high-frequency tweeter and a passive crossover/protection circuit network. The
coverage angle is 130° and includes a four-position, 5.08 pluggable Euroblock
connector and two RJ-45 connectors for audio signal connections.
The C-IC6 speaker supports audio connections via either standard category
cable or traditional speaker cable. The loudspeaker includes a tile bridge kit
for secure installation in a ceiling. It also features a magnetic grill for tool-less
installation and removal. The grille plate is available in white, black or red, and
can be painted to match the room decor.
The optionally-available AMP-450BP includes an audio locate feature on the
front face that allows installers to validate cabling and connections before the
audio system is fully commissioned.
Installation
Install away from heat sources, such as vents, radiators, heat registers
and stoves. Also avoid installing near water or steam. The conferencing
loudspeaker has a secondary support point via chain or wire for connecting
to the building structure. Do not exceed the maximum ambient operating
temperature of 32° - 95° F (0° - 35° C).
Per UL 1480A Section 6.1.6 - Use watertight cable, conduit, or EMT ttings for
installation in outdoor or wet locations.
The loudspeaker includes a tile bridge installation kit. Detailed installation
instructions are on the following pages.
Features
• Low-profile passive speaker, less than 6-inches (153 mm) total depth
• 8-ohm nominal impedance
• 130° coverage angle optimized for low ceilings
• Supports both standard category cables and traditional speaker wiring for
audio connections
• Designed for integration with the AMP-450BP (backpack PoE+ amplifier)
• Bridge-mounted 1-inch (25 mm) soft dome tweeter
• 6.5-inch (165 mm) treated paper woofer mechanically isolated from the high
frequency driver
• 60W with peak power of 240W
desono™C-IC6 Loudspeaker
Installation & Operation Guide
A: 9300 S.W. Gemini Drive Beaverton, OR 97008 USA T: +1 503.641.7287 W: www.biamp.com
JUNE 2019
Loudspeaker Installation
The C-IC6 loudspeaker is designed to be installed with the included tile
bridge kit and may be installed with or without above ceiling access. It is
at the discretion of the installer to determine the most practical method of
installation while making sure any required safety or regulatory precautions
are followed.
Prior to cutting drywall or ceiling tiles, verify speaker wiring location.
For drop-ceiling installations, do the steps that follow:
1. Locate the center of the tile and use the included tile bridge C-Ring
as a template to mark the speaker cutout with a pencil or appropriate
implement.
2. Cut along the traced line and remove the cutout ceiling material.
3. Remove any rough material or other debris from the cutout and in and
around the hole.
4. Install the two tile bridge rails parallel to each other on either side of the
cutout as shown.
5. Place the C-Ring over the tile bridge rails as shown.
desono™C-IC6 Loudspeaker
1. Connector Cover and Hardware
2. RJ-45 (x2) and Euroblock Connector
3. Hanger Bracket
4. Clamp Assembly (x4)
5. AMP-450BP (PoE+ amplier) Attach Points
6. Speaker Grille
A: 9300 S.W. Gemini Drive Beaverton, OR 97008 USA T: +1 503.641.7287 W: www.biamp.com
JUNE 2019
6. Install the two screws that secure the C-Ring to the tile bridge rails.
7. Remove the grille from the loudspeaker and lift it adjacent to the cutout.
8. Connect the loudspeaker cabling to the appropriate connections.
9. Connect the hanger bracket to a safety chain/cable if required.
10. Insert the speaker assembly into the cutout. Tighten the clamp assembly
screws so the frame legs rotate and clamp the loudspeaker to the C-Ring
and ceiling tile.
11. Replace the loudspeaker grille.
For drywall ceiling installations, do the steps that follow:
1. Use the included tile bridge C-Ring as a template to mark the
loudspeaker cutout on the drywall ceiling with a pencil or appropriate
implement. The tile bridge rails are not needed for this installation.
2. Cut along the traced line and remove the cutout ceiling material.
3. Remove any rough material or other debris from the cutout and in and
around the hole.
4. Insert the C-Ring through the hole. The C-Ring must be manipulated by
inserting one end in the cutout and feeding/slightly twisting it until it is
above the ceiling/in the plenum space.
5. Set the C-Ring in the ceiling cutout.
6. Remove the grille from the loudspeaker and lift it adjacent to the cutout.
7. Connect the loudspeaker cabling to the appropriate connections.
8. Connect the hanger bracket to a safety chain/cable if required.
9. Insert the speaker assembly into the cutout. Tighten the clamp assembly
screws so the frame legs rotate and clamp the loudspeaker to the C-Ring
and ceiling.
10. Replace the loudspeaker grille.
Wiring
The C-IC6 may be wired to an appropriate amplier using a Euroblock
connector or via the RJ-45 connector to one of biamp’s PoE+ ampliers. The
AMP-450BP may be mounted directly to the C-IC6 for convenient installation.
A: 9300 S.W. Gemini Drive Beaverton, OR 97008 USA T: +1 503.641.7287 W: www.biamp.com
JUNE 2019
PoE+ Amplier Wiring Examples
Standard Amplier Wiring Example
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Biamp Intervenants
Biamp
Biamp OVO3T Manuel utilisateur
Biamp
Biamp P30DT Series Manuel utilisateur
Biamp
Biamp Desono MASK4C Instructions d'utilisation d'origine
Biamp
Biamp Desono EX Series Instructions d'utilisation d'origine
Biamp
Biamp L Series Instructions d'utilisation d'origine
Biamp
Biamp R1 Series Mode d'emploi
Biamp
Biamp Desono DX-S5 Instructions d'utilisation d'origine
Biamp
Biamp Desono CM Series Manuel utilisateur
Biamp
Biamp Desono SPA-GHH100 Manuel utilisateur
Biamp
Biamp Cambridge Qt X 300 Instructions d'utilisation d'origine
Biamp
Biamp Desono P6 Instructions d'utilisation d'origine
Biamp
Biamp Desono DX-S5-UB Instructions d'utilisation d'origine
Biamp
Biamp SPA-TR100 Manuel utilisateur
Biamp
Biamp R2 Series Mode d'emploi
Biamp
Biamp Desono DX Series Instructions d'utilisation d'origine
Biamp
Biamp Desono MASK2 Instructions d'utilisation d'origine
Biamp
Biamp Desono SPA-GRB100 Manuel utilisateur
Biamp
Biamp MPLT62-G Mode d'emploi
Manuels Intervenants populaires d'autres marques
Bowers & Wilkins
Bowers & Wilkins 4 Manuel utilisateur
Sonance
Sonance SONOS OUTDOOR Series Manuel utilisateur
Electro-Voice
Electro-Voice EVID FM4.2 Manuel utilisateur
Pioneer
Pioneer XW-HTD630 Manuel utilisateur
Onn
Onn BWA16AA002 Manuel utilisateur
HP
HP GL313AA - USB Speakers PC Multimedia Manuel utilisateur