BH LK550 Mode d’emploi

Table des matières

Autres manuels BH vélo d'appartement

BH

BH REX Manuel de l'opérateur

BH

BH LK700U Manuel utilisateur

BH

BH BLADEZ MASTER MAG Manuel utilisateur

BH

BH G820 Manuel de l'opérateur

BH

BH H945BM Manuel de l'opérateur

BH

BH LK700FB Manuel utilisateur

BH

BH H9168E Manuel de l'opérateur

BH

BH BLADEZ ECHELON GS Manuel utilisateur

BH

BH BLADEZ 200U Manuel utilisateur

BH

BH H862 Manuel de l'opérateur

BH

BH S3Ri Manuel utilisateur

BH

BH LK500Ei Manuel utilisateur

BH

BH BLADEZ 200R Manuel utilisateur

BH

BH H853 Manuel de l'opérateur

Manuels vélo d'appartement populaires d'autres marques

Weslo

Weslo Vector 302 Guide de démarrage rapide

TOORX

TOORX BRX85 Manuel utilisateur

Matrix

Matrix KranKcycle Manuel utilisateur

Matrix

Matrix IC3 Manuel utilisateur

Sunny Health & Fitness

Sunny Health & Fitness SF-B121021 Manuel utilisateur

Monark

Monark 827E Manuel utilisateur

Stamina

Stamina 1310 Manuel utilisateur

American Fitness

American Fitness SPR-BK1072A Manuel utilisateur

Cateye

Cateye CS-1000 (CYCLO SIMULATOR) Manuel utilisateur

BH FITNESS

BH FITNESS H9158H Manuel de l'opérateur

Body Sculpture

Body Sculpture BC-7220G Manuel utilisateur

Cateye

Cateye EC-2300 Manuel utilisateur

FYTTER

FYTTER RACER RC MSR Manuel utilisateur

Kikos

Kikos HM-9090M Manuel utilisateur

Pro-Form

Pro-Form 345 Zlx Bike Guide de l'utilisateur

Fuel Fitness

Fuel Fitness SU135-40 Manuel utilisateur

NordicTrack

NordicTrack Gxr 4.2 Bike Manuel utilisateur

Vision Fitness

Vision Fitness U70 Manuel utilisateur

Calibration of the LK550 Adjustment Motor Instructions

(Page 1 of 2)

Objective: There are times when the LK550 adjustment motor may need calibration. Below are the

calibration instructions.

Instructions:

1. For safety disconnect the power Adaptor (H2) so there is no power to the unit.

2. Remove both Left and Right Cranks (A26 & A27). Remove DC Line (A6-2) from left Chain Cover.

Remove Left and Right Chain Covers (A30 & A32).

3. Remove the cotter pin from the end of the Tension Cable (A6-1) on the Adjustment Motor (A6) as

shown below.

4. Pull the Magnetic Housing (A11-3) away from the Magnetic Wheel (A11) to allow slack on the Tension

Cable and slide the Tension Cable up off the fastening pin on the Adjustment Motor as shown below.

5. Adjust Tension Cable tube so that the tube protrudes approximately half its distance as shown below

and tighten with fastening nut.

Cotter Pin

Tension Cable

Adjustment Motor

Fastening Pin

Adjustment Motor

Calibration of the LK550 Adjustment Motor Instructions

(Page 2 of 2)

6. Connect the power Adaptor (H2) and observe the movement of the Adjustment motor fastening pin as

it moves into position “0”.

7. Disconnect the power Adaptor.

8. Pull the Magnetic Housing away from the Magnetic Wheel to allow slack on the Tension Cable again

and slide the Tension Cable back on to the fastening pin on the Adjustment Motor.

9. Connect the power Adaptor again, the Adjustment Motor will re-position again.

10. Press the “+” button to increase the resistance on the Adjustment Motor to maximum and observe the

Magnetic Housing get closer to the Magnetic Wheel. Press the “-“ button and observe the Magnetic

Housing get further from the Magnetic Wheel.

11. Repeat these steps while pedaling to make sure the resistance increases while increasing the

resistance on the Computer.

12. Re-install the cotter pin.

13. Re-install the Chain Covers, DC Line and Cranks in this order.

14. The Adjustment Motor is now calibrated.

Tension Cable Tube

Fastening Nut

Magnetic Housing