BFT PHOBOS N BT Comment utiliser
PHOBOS N BT & PHOBOS NL BT
INSTALLER REFERENCE
VERSION 101115
550 lbs
10 feet
90°
Phobos N BT
110°
Phobos NL BT
16 feet
550 lbs
OUTSIDE
4” max hinge
offset*
OUTSIDE
5” max hinge
offset*
32 1/2”
37”
APPLICATIONS AND CAPABILITIES2
* Maximum hinge offset does not apply to push to open applications
INSTALLATION CHECKLIST 3
Determine the proper geometry. Pages 4 & 5.
Insta the Post bracket. Page 6 & 7.
Insta the Gate Bracket. Page 7.
Insta the magnet ho der. Page 7
Wire the motors. Page 8.
Attach the actuators to the mounting brackets. Page 8.
Set the imit switches. Page 9.
Connect the motors to the contro board. Page 10.
Insta and connect your safety devices. Page 11.
Insta and connect your operating devices (if app icab e). Page 11.
Insta and connect your magnetic ock (optiona ). Page 12.
Program your remotes. Page 13.
Set your contro er to Sing e Motor Operation if needed. Page 13.
Run and time your motors from fu y open to fu y c osed positions.
Set your s owdown settings. Page 14.
Set the torque adjustment. Page 14.
Set additiona features as needed. See Programming Menu Reference page (Back cover).
TECH SUPPORT U.S. TOLL FREE: 877 995 8155 / INT'L: +1 561 995 8155
A
B
A
90°
90°
B
90°
90°
PIVOT POINT
PIVOT POINT
PHOBOS' PIVOT POINT
Gate hinge
Gate frame
Gate
post
C
C DIMENSION For C dimension, the measurement is taken from the Phobos pivot point
to the center of the arge ho e on the gate bracket WITH THE GATE ON ITS FULLY
CLOSED POSITION.
Gate bracket
A & B DIMENSIONS For A and B dimensions, the measurement is taken from the center
of the gate's hinge point to the center of the Phobos pivot point.
SQUARE WITH THE GATE It is very important that the measurements are taken using
the gate frame fu y c osed as perpendicu ar ang e reference. If a fu y c osed gate is not
square with the gate post, you must make the proper ang e adjustments.
DEFINING THE BRACKET GEOMETRY4
For Push to Open applications, please call Tech Support at 877 995 8155
Table 2.1
IDEAL GEOMETRY A symmetrica geometry wi give you even speed and torque throughout the entire
movement of the gate as we as equa y strong everage to ho d the gate in position at both open and c ose ends
of strokes. If you are we ding the post bracket, when possib e, use the geometry in tab e 1:
Table 1
USING THE ARB BRACKETS The ARB adjustab e brackets simp ify the insta ation process.
The tab es 2.1 and 2.2 gives you different options depending on the three most common gate
hinge offsets. These dimensions on y app y to insta ations where the fu y c osed gate is square
with the gate post. DO NOT DEVIATE FROM THE DIMENSIONS ON THE TABLES
Gate hinge
Gate frame
Gate
post
Hinge offset
Gate hinge offset – The gate
hinge offset is the distance
from the center of the gate
hinge to the inside edge of the
gate post
ARB
Table 2.2
A B C ARB
1 1/2” 5 1/8” 6 3/4” 27 1/2” 5 1/4”
2” 5 1/8” 6 5/8” 27 1/2” 4 5/8”
3” 4” 7 5/8” 27 1/2” 4 5/8”
HINGE
OFFSET
A B C ARB
1 1/2” 7 3/8” 7 3/8” 32 1/2” 5 7/8”
2” 7 1/2” 7 7/8” 32 1/2” 5 7/8”
3” 7 1/2” 7 7/8” 32 1/2” 4 7/8”
HINGE
OFFSET
PHOBOS N BT
ARB GEOMETRY
PHOBOS NL BT
ARB GEOMETRY
DETERMINING THE BEST GEOMETRY 5
A B C
PHOBOS N BT
PHOBOS N BT 5 7/8” 5 7/8” 27 1/2”
PHOBOS NL BT
PHOBOS NL BT 7 1/2” 7 1/2” 32 1/2”
For Push to Open applications, please call Tech Support at 877 995 8155
ARB BRACKET LENGTHS
ARB BRACKET LENGTHS To achieve the desired ARB ength, use a 3 bo ts on the
ho es that are represented by b ack dots on the i ustration of the ong bracket piece.
Insert them on y on the ho es that are represented by b ack dots on the short bracket
piece. The ong piece can be f ipped to match the ho es on the short piece.
5 5/8”
5 1/4”
5 7/8”
6
3 7/8”
Phobos N BT gate bracket
5 3/8”
Phobos N L BT gate bracket
1) DETERMINE THE PROPER GEOMETRY FOR YOUR INSTALLATION. You can use the tab e be ow to
write down your dimensions.
3) BOLT AND/OR WELD THE GATE BRACKET ACCORDING TO YOUR GEOMETRY. Remember to
measure the distance to C with a fu y c osed gate.
WELD OR BOLT
4) INSTALL THE MAGNET HOLDER OVER THE GATE BRACKET. Do
not insta before or right after we ding. Wait for bracket to coo down. Do
not try to operate the actuators without the magnet ho der in p ace.
2) BOLT AND/OR WELD THE POST BRACKET ACCORDING TO YOUR GEOMETRY.
SIDE A B C ARB
RIGHT LEAF
LEFT LEAF
HINGE
OFFSET
MY GEOMETRY
INSTALLING THE MOUNTING BRACKETS 7
C
OFFSET
ARB
A
B
WHITE
RED
BLACK
14 AWG STRANDED
1) WIRE THE MOTORS Before attaching the actuator to the mounting brackets, wire
the motor cab e and then insta the protective cover as i ustrated.
2) ATTACH THE ACTUATOR Fo ow i ustrations to insta the actuator to the post and gate
brackets.
INSTALLING THE ACTUATOR
8
1) SET TO MANUAL OPERATION - Disengage the drive gear by using the triangu ar key and turning
c ockwise.
2) SET THE CLOSE LIMIT - Push the gate to its fu y c osed position. Remove the screw that ho ds the
proximity sensor at the front end of the actuator. S ide it back so that the back end of the sensor
housing is 3-1/2” from the center of the drive carriage and re-attach screw that secures sensor in
p ace.
3) SET THE OPEN LIMIT - Push the gate to its fu y
open position. Remove the screw that ho ds the
proximity sensor c osest to the actuator body. S ide it
forward so that the back end of the sensor housing is
3-1/2” from the center of the drive carriage and re-
attach screw that secures sensor in p ace.
3-1/2”
4) RE ENGAGE THE MANUAL RELEASE - Use triangu ar key and turn counterc ockwise to re-
engage gears.
SETTING THE LIMIT SWITCHES 9
SINGLE MOTOR OPERATION
DUAL MOTOR OPERATION
16 AWG
NOTE: For push to open app ications, the RED
and BLACK wires are reversed
CONNECTING THE MOTORS10
2
3
1
2
3
1
35
4
68
7
Autres manuels pour PHOBOS N BT
6
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels BFT ouvre-porte
BFT
BFT CLONIX1-2 Manuel utilisateur
BFT
BFT GIUNO ULTRA BT A20 Manuel utilisateur
BFT
BFT CELLULA 180 Manuel utilisateur
BFT
BFT ARES Manuel utilisateur
BFT
BFT LUX BT 2B Manuel utilisateur
BFT
BFT IGEA Manuel utilisateur
BFT
BFT LUX Manuel utilisateur
BFT
BFT EOS 120 VENERE D Manuel utilisateur
BFT
BFT DEIMOS BT KIT UL Manuel utilisateur
BFT
BFT ELI BT A35 V Manuel utilisateur
BFT
BFT LEO B CBB DL2 3 230 L02 Manuel utilisateur
BFT
BFT PHOBOS N BT Manuel utilisateur
BFT
BFT EBB KIT BL-LARGE Manuel utilisateur
BFT
BFT DEIMOS BT Manuel utilisateur
BFT
BFT WIND AC A230/240-76 EF Manuel utilisateur
BFT
BFT DEIMOS BT A400 120 Manuel utilisateur
BFT
BFT LUX BT 2B Manuel utilisateur
BFT
BFT PHOBOS N Manuel utilisateur
BFT
BFT MOOVI AC 30 Manuel utilisateur
BFT
BFT LEM7 Manuel utilisateur
