Bewator FH07B Series Manuel utilisateur

FH07B Series

Phoenix™ 7” Flameproof

Camera Housing

INS00306 Page 1 of 24

Installation Instructions

Manual: INS00306 Issue: 3.0

FH07B Series Installation Instructions Issue 3.0

INS00306 Page 2 of 24

IMPORTANT NOTE

Please thoroughly read these Instructions before installing the

FH07B Series Phoenix™ 7” Flameproof Camera Housing.

Table of Contents

About This Manual...................................................................................................................................3

Health & Safety Notice.............................................................................................................................3

INTRODUCTION......................................................................................................................................5

General Description .................................................................................................................................5

Contents of Package................................................................................................................................9

Before Starting Installation.......................................................................................................................9

After Installation .......................................................................................................................................9

Suggested Tools....................................................................................................................................10

ORDERING THE FH07B SERIES UNIT ...............................................................................................11

Certification Requirements For The Camera/Lens ................................................................................11

INSTALLING THE FH07B SERIES UNIT.............................................................................................12

Removing The Rear Cap Assembly.......................................................................................................12

Pre-installation Wiring............................................................................................................................13

Refitting The Rear Cap Assembly And Fitting The Sunshield...............................................................18

Locating The Unit...................................................................................................................................19

Mounting The Unit..................................................................................................................................19

MAINTENANCE.....................................................................................................................................20

1 Month After Installation .......................................................................................................................20

6 Monthly Checks...................................................................................................................................20

2 Yearly Checks.....................................................................................................................................20

5 Yearly Checks.....................................................................................................................................20

SPECIFICATIONS.................................................................................................................................21

Mechanical.............................................................................................................................................21

Electrical.................................................................................................................................................21

Mechanical Dimensions.........................................................................................................................22

Wiring Diagram ......................................................................................................................................23

NOTES...................................................................................................................................................24

FH07B Series Installation Instructions Issue 3.0

INS00306 Page 3 of 24

About This Manual

This manual describes the following equipment, certified to the EC (ATEX) Directive

94/9/EC as II 2 GD (EEx d IIB T85°C):

FH07B-40 Phoenix™ 7” diameter, IP67, Camera Housing (420 x114 x 93mm

internal) c/w sunshield, demister ~ 230Vac.

FH07B-40/L Phoenix™ 7” diameter, IP67, Camera Housing (420 x 114 x 93mm

internal) c/w sunshield, demister ~ 24Vac.

FH07B-40/U Phoenix™ 7” diameter, IP67, Camera Housing (420 x 114 x 93mm

internal) c/w sunshield, demister ~ 110Vac.

FH07B-30 Phoenix™ 7” diameter, IP67, Camera Housing (290 x 114 x 93mm

internal) c/w sunshield, demister ~ 230Vac.

FH07B-30/L Phoenix™ 7” diameter, IP67, Camera Housing (290 x 114 x 93mm

internal) c/w sunshield, demister ~ 24Vac.

FH07B-30/U Phoenix™ 7” diameter, IP67, Camera Housing (290 x 114 x 93mm

internal) c/w sunshield, demister ~ 110Vac.

Health & Safety Notice

SELECT SUITABLE EQUIPMENT

• Please ensure that all equipment is suitable for the application and the environment for

which it is intended.

• Check operating temperatures and where applicable “protection against water ingress”

specifications.

• Please take particular care that the inter-connected equipment is fully compatible with

each other and suitable for such use.

• Check load ratings and dimensions.

SECURELY MOUNT THE ASSEMBLY

• This equipment may be subject to remote control and may move at any time. It should be

installed such that moving parts cannot be exposed to anyone. Persons working on the

equipment should take appropriate precautions to ensure that unexpected movement does

not occur as this could lead to injury.

• This unit must be mounted properly and securely.

• In situations where there could be a risk of injury, should any part of the assembly become

detached for any reason and fall, normal safety precautions should be employed.

• Care should be exercised to select suitable hardware to install the unit, taking into

account both the compositions of the mounting surface and the total weight of the

hardware.

• It is important that only the recommended or supplied fixings are used. In some cases

the fixings material and other details are critical.

• Ensure that each part of the assembly is attached securely.

FH07B Series Installation Instructions Issue 3.0

INS00306 Page 4 of 24

• The mounting surface must be sufficiently solid and strong to take the complete weight of

the assembly and take into account environmental aspects such as exposure to strong

wind.

• It is recommended that the bracket and column spacers detailed on Page 21 should be

used, where appropriate.

• As the mounting surface to which this housing could be attached is site dependent,

Bewator Ltd. does not supply fixings for securing the base of the unit to its mounting

surface. It is the responsibility of installers to ensure that fixings are selected that are fit for

the specific purpose required.

INSTALL OUT OF REACH

• This equipment is to be installed out of reach of the user, or anyone who will come into

casual contact with the installation.

• It is recommended that a prominent warning notice be affixed near to all moveable

Camera Housing assemblies indicating that sudden movement of the equipment may

occur.

• Be sure to provide suitable access equipment to ensure the safety of installation or

service personnel working on the equipment.

INSTALL CORRECTLY

• All persons installing and maintaining this equipment should be suitably qualified and work

to national and local standards and codes of practice.

• Use the appropriate tools. Specific tools may be required for installation purposes

dependant upon the site in which the assembly is to be installed.

• The installation should comply with local codes and standards e.g. EN 60079–14:1997

and its guide PD 60079-14:2000.

• Check that correct cable types and input cable glands are used - Refer to local and

national standards for wiring and follow recommendations.

• Always use the recommended or supplied screws. Failure to do so will invalidate the

certification to EC (ATEX) Directive 94/9/EC.

• Ensure that power is removed from the assembly before attempting installation.

• Ensure the power CANNOT be re-connected by external sources while the unit is being

worked upon.

• Installation must comply with data protection and privacy codes of practice.

WARNINGS

The unit must be connected to Earth.

Do not open the unit when an explosive atmosphere is present.

FH07B Series Installation Instructions Issue 3.0

INS00306 Page 5 of 24

Introduction

General Description

Hazardous Areas

The Phoenix™ 7” FH07B Series Flameproof Camera Housing is certified to the EC (ATEX)

Directive 94/9/EC for use in hazardous areas.

A hazardous area is defined as an area in which explosive atmospheres are, or may be

expected to be, present in quantities such as to require special precautions for the

construction and use of electrical equipment. An explosive atmosphere consists of a mixture

of flammable substances with air in the form of gas, vapour, mist or dust in such proportions

that it can be exploded by excessive temperatures, arcs, sparks or flames.

Equipment is housed in an enclosure into which gas may gain access. Should this gas be

ignited within the enclosure, the resulting explosion will not reduce the pressure integrity of

the enclosure or will not be transmitted to any flammable atmosphere external to the

enclosure.

Note: This equipment may contain an ignition source even after disconnection.

Customer Orders

The FH07B Series of Flameproof Camera Housings are fitted with a customer (free issue)

supplied Camera and Lens and supplied with ATEX Equipment Certification by Bewator Ltd.,

at an additional cost. (Bewator Ltd. Part Number FH07-CERT). The Camera/Lens and the

installation MUST be compatible with the certification to the EC (ATEX) Directive 94/9/EC,

see Page 11. Bewator Ltd. can supply and fit suitable cameras and lenses on request.

The FH07B Series of housings can be supplied fitted with the following optional accessories:

FH07W Wiper Unit Kit ~ 230Vac ~ 50/60Hz.

FH07W/L Wiper Unit Kit ~ 24Vac ~ 50/60Hz.

FH07W/U Wiper Unit Kit ~ 110Vac ~ 60Hz.

FH07-RX210 10 - function Receiver Kit ~ 110-230Vac.

FH07-RX217 17 - function Receiver Kit ~ 230Vac.

FH07-TKIT Tamper Switch Kit.

To ensure compliance with the certification to the EC ‘ATEX’ Directive 94/9/EC, ANY of

these optional accessories MUST be pre-ordered and supplied factory fitted by Bewator Ltd.

The maximum combined power dissipation for all of the equipment fitted into the Camera

Housing MUST not exceed:

FH07B-40 Series 63W

FH07B-30 Series 50W

To ensure compliance with the EC (ATEX) Directive 94/9/EC, all orders that are placed for

Phoenix™ 7” FH07B Series Camera Housings MUST follow Bewator Ltd. Procedure

20G040, which includes the completion of a Phoenix™ Pre-Compliance Form by the

customer.

FH07B Series Installation Instructions Issue 3.0

INS00306 Page 6 of 24

Certification

EC (ATEX) Directive 94/9/EC Certification is to :-

CE Marking. Bewator Ltd. Declaration Of Conformity. Bewator Ltd. Quality

System certified to ISO9001.

Specific explosion protection mark.

II Equipment group II. Group II comprises equipment intended for use in places

liable to be endangered by explosive atmospheres, other than mining

applications.

2 Equipment category 2. Equipment in this category is intended for use in

areas in which explosive atmospheres caused by gases, vapours, mists or

air/dust mixtures are likely to occur frequently under normal operating

conditions.

G Explosive atmospheres caused by gas.

D Explosive atmosphere caused by dust.

European Harmonised Standard EN 50014:1998 and EN 50018:2000 Certification is to:

E Complies with European Harmonised Standard.

Ex For use in explosive atmospheres.

dFlameproof enclosure to European Harmonised Standard EN 50018.

IIB Gas Grouping – For atmospheres containing ethylene or gases of an

equivalent hazard. Also includes Gas Group IIA for atmospheres containing

propane or gases of an equivalent hazard.

Zone 1 Hazardous area zone – Where an explosive atmosphere is likely to occur in

normal operation. Also includes Zone 2, where an explosive atmosphere is

not likely to occur in normal operation and if it does occur it will exist only for a

short time.

T85°C Temperature - Based on an ambient temperature of 40°C, the maximum

surface temperature generated by the unit, with approved internal fittings,

does not exceed 85°C.

EC-Type Examination Certificate

Baseefa (2001) Ltd., Buxton, UK, notified body number 1180, certifies compliance of the

equipment with the EC (ATEX) Directive 94/9/EC.

EC-Type Examination Certification Number: Baseefa03ATEX0464X.

European Harmonised Standard EN 60529:1992 Certification is to:

IP67Ingress Protection

IP6X Dust tight. No ingress of dust at normal temperature and pressure.

IPX7 Protected against the effects of temporary immersion in water. Immersed for

30 minutes at a depth of 1.00m.

Abtest Limited, Abercynon, UK certifies compliance of the equipment to the Standard EN

60529:1992, with an IP67code.

Environmental Test Report No : EQ8481, dated 16 July 2003.

FH07B Series Installation Instructions Issue 3.0

INS00306 Page 7 of 24

Equipment Marking

The equipment has a special yellow label attached to the outside of the Rear Cap Assembly.

The label includes the following:

1180 II 2 GD EEx d IIB T85°C

Equipment Description

• The housing is manufactured using a 7” external diameter extruded aluminium body

(polyester powder coated) with two clear anodised aluminium Front and Rear (end)

Caps.

• The housing body incorporates 6 off M6 x 1.0 screw thread holes, in two sets of 4 holes

equi-spaced on a 4” (101.6mm) p.c.d. (pitch circle diameter), to enable the housing to be

mounted on a suitable surface.

• The Front Cap Assembly incorporates a 15mm thick toughened glass window.

• Two M4 screw mounting holes are provided on the Front Cap Assembly, beneath the

glass window, for fitting additional user supplied accessories (See Figure 1).

Note: The penetration of the M4 mounting screws into the Front Plate Assembly

mounting holes MUST NOT exceed 8mm. It is recommended that dimensional checks

be performed to determine the correct length of the M4 mounting screws.

• The Rear Cap Assembly includes a ‘mono rail’ assembly to which is fitted a

Camera/Lens and any optional accessories. It also includes 4 off M20 x 1.5 screw

thread cable entries, which are normally fitted with stopping plugs on delivery.

• 4 off ATEX certified flame proof Cable Glands are supplied for use with suitable cable.

(See Page 13.)

• Housings are available in six variants - two lengths (nominally 290mm and 420mm

internal) and three ac mains input voltages (230Vac, 110Vac and 24Vac).

• A Terminal Block Assembly, fitted to the ‘mono rail’ assembly, is used where required for

the connection of external electrical equipment.

• Housings are provided with an external Earth Bonding Stud.

• A thermostatically controlled window demister (heater) and a Sunshield are fitted as

standard.

• Spare Wiper Arm and Blade Kits (Bewator Ltd. Part Number WI01AB) are also available.

• A detailed product specification is provided on Page 21.

FH07B Series Installation Instructions Issue 3.0

INS00306 Page 8 of 24

Figure 1 Typical Flameproof Camera Housing

Figure 2 Detail Showing Flame Path Zone Locations

FH07B Series Installation Instructions Issue 3.0

INS00306 Page 9 of 24

Contents of Package

The product should reach you in perfect working order. If the unit is damaged in any way or

if the supplied kit is incomplete, please contact Bewator Ltd. immediately.

1 x FH07B Series Camera Housing, including Sunshield, fitted with optional accessories.

1 x General Packing Kit comprising:

4 x M5 x 16 Hex Socket Button Head Screw.

4 x M5 Nylon Washer.

3 x M5 x 60mm M5 Hex Head Special - Rear Cap Removal Screw.

2 x M6 x 70 Cap Head - Rear Cap Fitting Guide Screw.

4 x Cable Gland (Hawke Cable Gland Type 501/421).

1 x Installation Instructions INS00306.

Optional

1 x Optional Accessories Packing Kit comprising:

Either 1 x Installation Instructions INS00054 (complete with ‘D’ Type Telemetry Module)

– 10 function Receiver [RX210].

Or 1 x Installation Instructions INS00093 (complete with ‘D’ Type Telemetry Module)

– 17 function Receiver [RX217].

Before Starting Installation

1. Ensure that the contents of the package (see above) are correct.

2. Read all of these Installation Instructions.

3. Ensure that the correct tools are used when installing – see below.

4. Ensure that the complete assembly is tested in the workshop, prior to installation on

site.

After Installation

1. Save these Installation Instructions for future use.

2. Save the 3 off Rear Cap Removal Screws and the 2 off Rear Cap Fitting Guide

Screws for future use.

FH07B Series Installation Instructions Issue 3.0

INS00306 Page 10 of 24

Suggested Tools

The following tools are suggested for the installation of a FH07B Series Flameproof Camera

Housing:

• 3mm A/F (across flats) Allen key

• 5mm A/F (across flats) Allen key

• 10mm A/F (across flats) Allen key

• No 1 ‘Posidrive’ screwdriver

• Torque wrench set to 4.5Nm

• Rubber hammer

• 8mm A/F (across flats) ring spanner

• Small flat bladed (electrical) screwdriver.

Table des matières

Manuels Caméra de sécurité populaires d'autres marques

Okina USA

Okina USA SIR36-870VF650LP Manuel utilisateur

Divio

Divio NDR155PA Manuel utilisateur

Canon

Canon VB-C500D Manuel utilisateur

Easy Access

Easy Access EasyGuard Manuel utilisateur

Vivotek

Vivotek FD9389-EHV-v2 Manuel utilisateur

TUYA

TUYA COSMO W2 Manuel utilisateur

Eusso

Eusso UNC7500-IR Guide de configuration

urmet domus

urmet domus 1096/204 Manuel utilisateur

VC VC20 series Manuel utilisateur

Axis

Axis Q1614 Manuel utilisateur

ieGeek

ieGeek DD201 Manuel utilisateur

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manuel utilisateur

Vicon

Vicon V662-D-1 Mode d'emploi

Grundig

Grundig GCH-K0274P Manuel utilisateur

Lorex

Lorex VANTAGE LBC7032 Manuel utilisateur

4xem

4xem WPT Manuel utilisateur

Samsung

Samsung SCV-3082 Manuel utilisateur

Vitek

Vitek VTC-C544 Manuel utilisateur