Besantek BST-LAN12 Manuel utilisateur
LAN CABLE TESTER
BST-LAN10
INSTRUCTION MANUAL
-1-
INTRODUCTION
● The Lan cable tester is a newly designed tool that can
easily test the correct pin conguration of the RJ45/
RJ11 modular cables, 10/100 base-T cable and Token
Ring cable etc.
● By comparing one transmitting end and the
corresponding receiving end, the Lan cable tester also
can test installed cable far away by using the remote
receiving unit.
● The LCT provides the variety for wiring check, such
as cable continuity, open status, short status and miss-
wired.
FEATURES
● Designed for RJ45/RJ11 modular cables, 10/100
base-T cable and Token Ring cable etc.
● The Lan cable tester can verify cable continuity, open,
short circuit and miss-wired.
● The remote receiving unit is available for installed
cables far away either on the wall plates or on the
patch panels.
● Auto and manual scan function.
● Ground wire test.
● Lock status function.
● Buzzer sound warning for wire status.
● Display: LED indication for wire status.
● EN61326-1
-2-
INSTRUMENT LAYOUT
(1) RJ45 jack of sourcing end.
(2) RJ45 jack of receiving end.
(3) LED indicator of sourcing end.
(4) LED indicator of receiving end.
(5) Auto scan control button.
(6) Test button for manual wire test.
(7) Power ON/OFF control button.
(8) Battery check button.
(9) Lock control button.
(2)
(3)
(4)
(5)
(6)
(7)
(1)
(9)
(8)
(11)
(10)
(15)
(16)
(12)
(13)
(14)
-3-
(10) Manual scan control button.
(11) Battery check LED.
(12) LED indicator of receiving end for ground wire test.
(13) LED indicator of sourcing end for ground wire test.
(14) RJ45 jack of the remote receiving unit.
(15) LED indicator of the remote receiving unit.
(16) LED indicator for ground wire test on remote
receiving unit.
SPECIFICATIONS
Display LED
Operating
Temperature 0°C~40°C
Power Source 9V (6F22,006P) battery x1
Dimensions Master unit
132(L)x 55(W)x 39(D)mm
Remote receiving unit
74(L)x 30(W)x 25(D)mm
Weight Master unit: 148 g
Remote receiving unit: 33 g
Accessories Instruction manual
Pouch
Battery
-4-
OPERATION
Loopback test
● Plug one end of the testing cable into the Rj45 jack of
sourcing end on the master unit and another end of the
testing cable into the RJ-45 jack of receiving end on
the master unit.
● Press the " " button, the master unit will start a
sequential scanning process if the master unit is in
"auto-scanning" mode.
● Press the " " button, the pin1 LED lamps of the LED
indicators will be alight if the master unit is in "manual-
scanning" mode.
Note: When the battery power is low, the testing results
may not be correct. Please replace with a new battery.
● You can choose a auto-scanning mode or a manual-
scanning mode by pressing the "AUTO" button or the
"MANU" button.
● The Lock function is available in "auto-scanning" mode.
● When the loop is "OPEN", you will hear the sound of
the buzzer.
Remote test
● Plug one end of the testing cable into the Rj45 jack of
sourcing end on the master unit and another end of
the testing cable into the RJ-45 jack of the remote
receiving unit, then make tests.
● Read the testing results from the LED indicator on the
remote receiving unit.
-5-
Receiving
end (IN)
Sourcing
end (OUT)
Remote Test
Wall Plate Patch Panel
Loopback Test
-6-
TEST RESULT
-7-
MAINTENANCE
● Battery replacement:
When press the "BATT" button, if the "BATT LED"
doesn't glow, replace with a new 9V battery.
● Cleaning and storage:
Periodically wipe the case deterged with a damp cloth;
do not use abrasives or solvents.
If the meter is not to be used for periods of longer
than 60 days, remove the battery and store them
separately.
Table des matières
Autres manuels Besantek testeur de câbles
Manuels testeur de câbles populaires d'autres marques
Radiodetection
Radiodetection RD8100 Manuel utilisateur
Vonaq
Vonaq EasyCheck 900 Manuel utilisateur
Softing
Softing CableMaster CM200 Manuel utilisateur
Microtest
Microtest 8751 Manuel utilisateur
Psiber Data Systems
Psiber Data Systems 20 Manuel utilisateur
Platinum Tools
Platinum Tools LANSeeker TP500C Manuel utilisateur
