Berker 7574 01 Series Guide produit
Operating and
assembly instructions
Instrucciones de uso
y de montaje
z r t s
7574 01 .., 7574 02 ..
Touch Panel Android/Windows
Panel táctil para Android / Windows
Painel táctil Android/Windows
Pekskärm Android/Windows
Contents
1 Safety instructions..........................................................................................3
2 Design and layout of the device .....................................................................4
3 Function..........................................................................................................5
4. Operation.......................................................................................................8
5 Information for electricians ...........................................................................19
5.1 Installation and electrical connection...................................................19
6 Appendix......................................................................................................24
6.1 Technical data .....................................................................................24
6.2 Troubleshooting...................................................................................26
6.3 Accessories.........................................................................................26
z
2
Touch Panel 7´´ Android
Order no.: 7574 01 07
Touch Panel 10´´ Android
Order no.: 7574 01 10
Touch Panel 10´´ Windows 7
Order no.: 7574 02 10
Touch Panel 16´´ Windows 7
Order no.: 7574 02 16
Operating and assembly instructions
1 Safety instructions
Electrical equipment may only be installed and assembled by qualied
electricians in accordance with the relevant installation standards of the
country.
Failure to comply with these instructions may result in damage to the de-
vice, re, or other hazards.
This is equipment of class A. It can cause radio interference in residen-
tial areas that the operator must counteract by means of appropriate
measures.
When supplying the system with Power over Ethernet (PoE) the overall
performance including all loads connected (e.g. USB devices) may not ex-
ceed the power consumption of IEEE 802.3af class 3.
In the case of device variants with PoE functions, make sure that no dif-
ferential ground potentials are used so that this function can be used.
When integrated into a door communication system (e.g. Elcom) or usage of
audio les the permissible PoE current consumption may be exceeded. This
may lead to a shutdown of the PoE supply. In this case a 24 V DC auxiliary
voltage supply is to be connected.
Do not operate the user interface with sharp-edged or pointed imple-
ments.
Do not use any sharp-edged implements for cleaning. Do not use any ac-
ids or organic solvents.
These instructions are an integral component of the product and must be
retained by the end user.
z
3
2 Design and layout of the device
(6)
(3)
(2) (4)
(5)
(1)
Figure1: Front view – Example 7´´ Android variant
(1) Touch-sensitive user interface
(2) Microphone
(3) Brightness sensor
(4) Socket for mini USB 2.0
(5) Reset button Rfor rebooting device
(6) Speaker
(3)
(4)
(5)
(7)
(9)
(5)
(10)
Figure 2: Rear/Side view – Android device variants
z
4
(3)
(4)
(10)
(11)
(8)
(7)
(9)
(12)
(13)
(5)
Figure 3: Rear/Side view – Windows device variants
(7) Gigabit Ethernet connection RJ45, LAN/PoE (7´´/10´´ Android variant)
(8) Gigabit Ethernet connection RJ45, LAN2 (10´´/16´´ Windows variant)
(9) Connecting terminal for auxiliary voltage 24 V DC
(10) Connections USB 2.0
(11) COM1, Serial RS232
(12) Slot for SD card with rmware and operating system
(13) Connection 3.5 mm jack
3 Function
System information
The device is a display obtainable as a variant with integrated Windows
embedded (PC) or an Android operating system. The capacitive touch display
is highly suitable for the central control and visualisation of building system
technology. Operating functions and system statuses are transmitted to the
touch panel via Ethernet by means of a local server such as the domovea
z
5
Server (see Accessories), which establishes the connection to the KNX sys-
tem.
In this way, for example, light can be switched and dimmed, hangings con-
trolled, temperature and consumption values displayed or emails read and
sent by means of a client on Windows or external applications (Apps) in the
Android-Launcher.
Product characteristics
- Operation directly on the screen with the touch of a nger
- Multi-touch function
- Displaying of congured functions, measured values and data
- Brightness sensor for screen illumination
- USB connections for external data storage media
- Microphone and loudspeaker with echo suppression
- Silent, long-lasting convection cooling without fan
- Disabling function for cleaning the user interface by means of Touch Block-
er (Windows variants)
- Applications (for Android touch panel) and iCom Module for the integration
of door communication functions in the Hager domovea client or
Elcom VideoFON client
- Visualisation for Berker IP-Control via browser
Correct use
- Only suitable for indoor applications
- The appropriate ush-mounted housing for touch panel (see accessories)
must be used for the ush-mounting in hollow walls or solid walls.
- The panel can be mounted in a horizontal or vertical direction.
Please note that the planned visualisation must correspond to the mount-
ing orientation of the touch panel. If, for example, a domovea visualisation
is implemented, both mounting orientations are only possible for the 7´´
variant. A horizontal mounting must be provided from a panel size of 10´´.
z
6
Figure 4: Application environment
Scope of delivery
- Touch panel
- USB/Mini USB type A adapter cable
- Installation material/tool
- RJ45 connector kit with connector and patch cable
- Operating system*) installed - depending on device variant:
- Windows7®embedded*) or
- Android 4.0.x
Additionally for Windows variants:
- Touch-Blocker preinstalled on the desktop
- Drivers for the hardware
- Recovery-DVD
*) Windows 7 embedded is a registered trademark of Microsoft Corporation.
domovea Client
(Android)
VideoFon Client
(Windows)
VideoFon Client
(Android)
Domovea Server
(KNX-IP Server)
IP Kamera
PoEPoE
LAN
LAN
LAN
LANPoE Router/Switch
IP Lautsprecher SIP
Internet
Klingeltaster
Mobile
Phone
Ruf-Modul
IP Server SIP
07
31
z
7
4. Operation
The screen has a touch-sensitive surface, called touch screen. By touching the
user interface with your nger or with a special touch screen pen (not included
in scope of delivery) stored actions and functions are activated.
Do not operate the user interface with sharp-edged
or pointed implements.
Depending on the software visualization, different operating modes are basi-
cally possible by means of the touch-sensitive user interface (Table 1).
Operating mode Explanation with examples
short touch Switch on/off, stop, activate/deactivate, ...
long touch Change dimming value, move blind, …
Single-surface opera-
tion: Switching on/off with the same control surface
Two-surface operation: Switching on/off using two control surfaces
Sliding Slide your nger over a control surface to variably
adjust a value, e.g.
dimming value or temperature value
Wiping For scrolling forwards or backwards through pages
Multi-Touch control Simultaneous pressing of several control surfaces to
interconnect two actions, e.g.
activating function and setting function value simul-
taneously
Table 1: Operating modes
If no action is executed on the display within a certain time period, the
device returns automatically to standby display (OFF or screensaver). This
time period can be congured individually – in the case of Windows vari-
ants in the control panel and in the case of Android devices by means of
Settings – Android settings – Display – Sleep in three levels
"Never, 1 Min., 5 Min., 10 Min., 30 Min.". The display is switched on again
by touching the user interface once again.
z
8
Loading les from external data storage media
Loading les from external data storage media
CAUTION!
The SD card slot cannot be used for external data storage media
with its own pictures, for example.
Factory settings and con gurations could be lost when removing
the SD card.
Never remove the SD card from the slot.
ç
A mini USB socket (4) is available on the upper edge of the display for loading
les, e.g. pictures, audios, updates as well as applications (Apps/programs)
from an external data storage medium.
If a device is mounted ush with the wall, press left and right evenly
against the housing until the locking mechanism is audibly released.
The device is guided out of the wall. The operating elements on the upper
edge are accessible.
Connect the enclosed adapter cable USB/mini USB to the socket (4) if
necessary.
Connect external data storage medium, such as a USB stick or hard disk,
to the adapter cable.
Store the data in the device or install applications using the Windows Ex-
plorer/a le manager.
Update/Recovery of Android Touch Panels via USB stick
The system software of Android Touch Panels as well as the domovea-App
can be restored using conventional USB sticks or changed to another software
version The integrated USB update- and Recovery-function can be used in
different manners depending on the dataset used::
- Recovery: system recovery, in this case the system software is completely
overwritten on the device with a suitable system software (typically the ver-
sion when supplied).
- Complete update: the system software is completely overwritten with a sui-
table system software (typically a newer version).
All user data is lost when performing the recovery and complete
updates.
z
9
- Partial update: only parts of the system software are overwritten or written.
Partial updates can be dimensioned in such a manner that the user data is
not lost. Partial updates are particularly suitable for subsequently installing
applications or for updating.
The procedure is the same in all cases, the different effects result from the
datasets used.
The following is required in order to carry out the software installation:
- Commercially available FAT32 formatted USB memory stick with minimum
512 MB free memory.
- Mini USB adapter cable (included in scope of delivery)
- Update / recovery-dataset (.zip archive, is offered int he download area for
the product)
- Archiving software (e.g., Windows Explorer , 7zip or similar)
In order to install a system software, we recommend the following procedure.
Download the dataset (.zip archive) from the download area for the product
Unzip the update / recovery dataset into the root directory of the USB stick
If a device is mounted ush with the wall, press left and right evenly
against the housing until the locking mechanism is audibly released.
The device is guided out of the wall. The operating elements on the upper
edge are accessible.
Connect the enclosed adapter cable USB/mini USB to the socket (4) if
necessary.
Connect the USB stick with the touch panel or adapter cable.
Restart the Android touch panel by pressing the reset button or by discon-
necting from the power supply,
Now the update / recovery is started automatically when starting up the
device.
Follow the instructions on the screen in order to conclude the procedure.
z
10
Ce manuel convient aux modèles suivants
5
Table des matières
Autres manuels Berker Écran tactile
Manuels Écran tactile populaires d'autres marques
IBASE Technology
IBASE Technology ASTUT-152-RE1S Manuel utilisateur
YASKAWA
YASKAWA TP 610C Manuel utilisateur
B&R
B&R Power Panel C Series Manuel utilisateur
Beijer Electronics
Beijer Electronics X2 control Manuel utilisateur
AXIOMTEK
AXIOMTEK GOT321W-521 Manuel utilisateur
TRIDONIC.ATCO
TRIDONIC.ATCO x-touchBOX Manuel utilisateur
