BenQ BL2420PT Manuel utilisateur

Recycle Disassemble Instruction

(Dismantled Information)

Requirements according to ANNEX VII of DIRECTIVE 2012/19/EU

on waste electrical and electronic equipment (WEEE)

Materials and components with hazardous content

LCDs may contain hazardous substances like Pb and BFRs which are covered by

exemptions under the RoHS directive. However, the majority is present in the printed

circuit boards assembly. In order to reduce emissions as much as possible, a complete

disposal of the old appliance is required. This treatment may only be performed in

authorized handling plants.

Product Name:

LCD Monitor

Model No.:

BL2420PT

Disassembly Tools

Tool picture

Philips Screwdriver for M3 Screw

Nosed Pliers

Diagonal Cutting Pliers

Slotted screwdriver

Six Point Sockets

Philips Screwdriver for M2.5 Screw

Knife

Disassembly process

1) Remove the base

Place the monitor face down on a smooth surface. Be careful to avoid scratch and injury during the process of uninstall.

Remove the screw and then rotate the base as below picture to remove the base.

2) Remove the stand.

Holding the stand and press the button, and so you can remove the stand.

Open

3) Remove the rear cover

Unscrew the screws from the rear cover.

Pull apart bezel & rear cover.

Note: Be careful, the BEZEL CLIP is easy to break.

Note: The positions of the clips on the rear cover are as follow. There are some small gaps between CLIPS. It’s

suggested to separate bezel and rear cover from the gaps.

4) Remove the main frame from the panel.

Remove the aluminum foil; pull out the wire marked in red circles to remove the mainframe.

Note: When you assembled the LCD, you must tidy the wire as follow picture.

Example: You can separate the

bezel and rear cover from

Turn over the mainframe to remove the tapes and LVDS cable.

5) Remove the AC cover from the mainframe.

6) Remove the Mylar from power board.

Remove the Mylar from power board.

7) Remove the boards from the main frame

And then remove screws in red, pull out the wire to remove the main board and power board.

Turn over the power board and main board; remove the speaker cable, and other cables.

The power board

The main board

8) Remove the speaker

Pull at the foot of the speaker strongly as follow picture.

9) Remove the panel

Note

：

Be course the panel is easy to broken, when we remove the panel, we should hold the iron on the panel

edge use two hands at the same time, and should avoid touching the panel surface.

10) The bezel unit.

Disassembly Time

Total time: 30 minutes

Autres manuels pour BL2420PT

1

Table des matières

Autres manuels BenQ Moniteur

Manuels Moniteur populaires d'autres marques

Linear Acoustic

Linear Acoustic LQ-1000 Manuel utilisateur

AOC

AOC I2579V Manuel utilisateur

Gateway

Gateway FPD1520 Manuel utilisateur

Furuno

Furuno Mu 120c Manuel utilisateur

Asus

Asus VB171D - 17" LCD Monitor Manuel utilisateur

Dell

Dell S2230MX Instructions d'utilisation

Philips

Philips 107C64 Manuel utilisateur

Dell

Dell S2409WFP Manuel utilisateur

EverFocus

EverFocus EN-7517E Manuel utilisateur

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Manuel utilisateur

Dell

Dell Precision 7680 Mode d’emploi

LG

LG 50PM1M - - 50" Plasma Panel Manuel utilisateur

Bosch

Bosch DDU 9 Manuel utilisateur

Acer

Acer A231HL Manuel utilisateur

Philips

Philips 86BDL4152T Manuel utilisateur

NEC

NEC AccuSync LCD5V Manuel utilisateur

Emay

Emay SleepO2 Manuel utilisateur

IBM

IBM 6360 Instructions d'installation