BenQ AWL-100 Manuel utilisateur
Benq Wireless LAN PCMCIA Adapter
AWL100
User Manual
Version 1.0
MPE Statement (Safety Information)
Your device contains a low power transmitter. When device is transmitted it sends out Radio
Frequency (RF) signal.
Safety Information
In order to maintain compliance with the FCC RF exposure guidelines, this equipment should
be installed and operated with minimum distance 2.5cm between the radiator and your body.
Use only with supplied antenna. Unauthorized antenna, modification, or attachments could
damage the transmitter and may violate FCC regulations.
Caution Statement of the FCC Radio Frequency Exposure
This Wireless LAN radio device has been evaluated under FCC Bulletin OET 65C and found
compliant to the requirements as set forth in CFR 47 Sections 2.1091, 2.1093, and
15.247(b)(4) addressing RF Exposure from radio frequency devices. The radiation output
power of this Wireless LAN device is far below the FCC radio frequency exposure limits.
Nevertheless, this device shall be used in such a manner that the potential for human contact
during normal operation—as a mobile or portable device but use in a body-worn way is strictly
prohibit. When using this device, a certain separation distance between antenna and nearby
persons has to be kept to ensure RF exposure compliance. In order to comply with the RF
exposure limits established in the ANSI C95.1 standards, the distance between the antennas
and the user should not be less than 2.5cm.
In order to avoid from mutual interference, this device must not be co-located or
operating in conjunction with any other antenna or transmitter.
Federal Communications Commission (FCC) Requirements, Part 15
This equipment has been tested and found to comply with the limits for
a class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in
a residential installation.
This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
---Reorient or relocate the receiving antenna.
---Increase the separation between the equipment and
receiver.
---Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
---Consult the dealer or an experienced radio/TV
technician for help.
The identification of the product:
Product Name : BenQ WLAN PCMCIA Adapter
Model : AWL100
BenQ Wireless LAN Technical Support:
BenQ Corporation
Address : 8, Jihu Rd., Nei-hu Dist., Taipei 114, Taiwan, R.O.C.
Telephone : 886-2-2799-8600
Fax : 886-2-2799-8822
Technical Support in the US:
BenQ Incorporated
Address : 20480 East Business Parkway, City of Industry,
CA 91789, USA
Telephone : 1-909-569-0700
Fax : 1-909-569-0701
WWW : www.benq.com
Benq Wireless LAN
AWL100 PCMCIA Adapter User Manual i
Contents
Contents ..........................................................................................................................i
1. Installation..................................................................................................................1
1.1 Driver Installation....................................................................................1
2. AWL100 Wireless Settings ........................................................................................3
2.1 Status ........................................................................................................5
3.2 Configuration...........................................................................................7
3.3 Encryption................................................................................................8
3.4 Site Survey...............................................................................................9
3.5 About......................................................................................................10
Benq Wireless LAN
AWL100 PCMCIA Adapter User Manual
1
1. Installation
1.1 Driver Installation
Insert AWL100 PCMCIA Adapter into your PC, and then Windows will show the
dialog –‘Add New Hardware Wizard’.
Select ‘Search the location of the driver’ and press Next button.
Benq Wireless LAN
AWL100 PCMCIA Adapter User Manual
2
Select ‘Specify a location’ and browse the Benq Wireless LAN CD to find AWL100.
For example, if your CD-ROM is drive D and you want to install the English version
of driver, the location is D:\AWL100\English.
Windows has found AWL100 PCMCIA Adapter. Press Next button.
Please wait while coping files.
Benq Wireless LAN
AWL100 PCMCIA Adapter User Manual
3
Press Finish.
Press Yes and restart your computer.
2. AWL100 Wireless Settings
You can launch AWL100 Wireless Settings utility by clicking the icon or from
Control Panel.
Benq Wireless LAN
AWL100 PCMCIA Adapter User Manual
4
Benq Wireless LAN
AWL100 PCMCIA Adapter User Manual
5
2.1 Status
State
The current state of the driver is displayed in this field. If the state reveals
“Associated,“ it means that the normal flow of operation is in Infrastructure mode.
This shows that the PC is already connected to access point and BSSID is also shown
in the form of hex digits. At the same time, the networking is available for the device.
In “Scanning ” state, it means that the node can not detect the SSID to get an access
point within range and is searching for an available access point. Also, if the driver
failed to initialize for some unknown reasons, this field will display an error message.
Rescan
The driver will restart and begin its Connection Procedure if the rescan button is
pressed. In general, the connection procedure will be different according to the Mode
of the driver.
Enable / Disable Radio
This button is used to enable or disable the radio of AWL100
Benq Wireless LAN
AWL100 PCMCIA Adapter User Manual
6
Current Tx Rate
This field shows the current radio channel which is being used for an active
connection.
Current Channel
This field shows the current radio channel which is being used for an active
connection.
Throughput
The instantaneous wireless Receive and Transmit throughput are displayed in bytes
per second in this field. Every two seconds, these values are updated.
Link Quality
This field reveals the quality of the current connection. Only when the node is in
Infrastructure Mode does the Link Quality bar graph become active. The bar graph
displays the link quality between the node and its Access Point. Over the bar graph, a
label summarizes the quality of the link which can take on one of the following
values:
“Not Applicable”
“Poor”
“Fair”
“Good”
“Excellent”
When the Link Quality becomes “Poor,” the driver will start to look for a better
Access Point. As a result, the Link Quality is a very good measure of receiving and
transmitting errors over the radio.
Signal Strength
Only when the node is in Infrastructure Mode does the Signal Strength bar graph
become active. This bar graph shows normalized signal strength as reported by the
radio, averaged over all frames over 100 bytes long which are received from the
Access Point.
Status information about the radio link is displayed in this tab. Detailed description
should be placed in this field.
Autres manuels pour AWL-100
1
Table des matières
Autres manuels BenQ Adaptateur
