Bend-Tech Dragon Manuel utilisateur
p.1
Bend-Tech Dragon Assembly Manual
IMPORTANT: Please read before unpack ng. Place sh pp ng
conta ner n a w de open area where you w ll have room to work
and assemble th s product.
Sh pp ng
•The Dragon Machine comes
in two separate shipping
containers: One for the
primary parts and one for
the rail extension.
•The primary container's
dimensions are 60x4 x72 in.
•The secondary container's
dimensions are 292x12x12
for the shorter machine.
(Length varies by the length
of machine purchased)
Inspect on
•Please make sure that your Dragon Machine product is
properly inspected to make sure there was no damage to
the machine during shipping and check to make sure that
all the parts are intact and present in the containers.
•Read the list of parts included on p.2-3.
p.2
Parts Included
1/2 inch bolt: 3/4 inch socket
Dragon
12 foot 21 foot
x4 x7
1/2 inch washer
Dragon
12 foot 21 foot
x4 x7
3/4 inch hex nut
Dragon
12 foot 21 foot
x4 x7
2 inch 9/16 coupling nut x2
5v Power Source
(for operator panel box) x1
Machine Power Cord x1
p.3
Operator Panel Box x1
Parallel Cord
(For operator panel box.
Located on part catcher) x1
Zip Ties Generous Amount
Fastener Screws x2
Tools Requ red
3/ to 1/2 inch Drive Ratchet
p.4
inch Socket Extension
1/2 inch Socket
(For shipping bolts and part catcher)
9/16 inch Socket
3/4 inch Socket
3/ inch socket
Power Drill w/Phillips Head Bit
(For opening shipping container)
p.5
Wire Cutters
(For zip ties)
5/16 inch Hex Wrench,
1/ inch Hex Wrench &
3/16 inch Hex Wrench.
Hand Truck (Dolly)
(Recommended)
Unload ng the Mach ne
Step 1: Using your power dr ll
and ph ll ps head b t, remove
the screws and disassemble the
primary shipping crate and
remove the top of the secondary crate. Place
wooden pieces aside and out of the way.
Step 2: Also using your power
dr ll and 5/16 nch hex
wrench, remove any additional
shipping screws and bolts from
the base of the machine, beak
p.6
and part catcher. Move the beak and part catcher
aside to easily access the bulk of the machine with
the hand truck.
Step 3: Use either the hand truck or the help of
two additional people to remove the machine from
the shipping crate and place it in the general area
where it will be assembled.
D smantl ng the Support Leg
Step 1: Using the ratchet and 3/4 nch socket
attachment, remove the bottom 3/4 nch bolt
underneath the end of the rail where it is secured
to the support leg. (Save th s bolt along w th the
nut for Assembl ng the New Ra l: Step 1.)
Step 2: Switch to the 9/16 nch
socket and remove the top two
remaining 9/16 nch bolts.
Now, remove the support leg
and retr eve the new ra l from
the sh pp ng crate at th s
po nt.
p.7
Assembl ng the New Ra l
Step 1: With the help of a
friend, and some sturdy
supports to prop up the new rail,
line the tail end of the supported
rail up to the end leg from the
previous step and affix the rail,
support leg and pulley system
together with the 3/4 nch nut
and bolt for the pulley center,
9/16 nch bolts, washers and coupler nuts
provided.
Be sure to remember the 3/4 nch bolt
and correspond ng nut from Step 1 of
D smantl ng the Support Leg that w ll
be secured to the bottom.
NOTE: The supports used to prop up the
bulk of the new ra l (Not Included)
should ra se the bottom edge up roughly
29 - 29 1/4 nches off the ground to match
the he ght of the stock ra l.
p.
Step 2: Line up the bare end of the new
rail with the 3 foot stock rail in
preparation to transfer the chuck to the
new rail.
Transferr ng the Chuck
Step 1: Use the chuck key
located in the slot on the top of
the chuck to loosen the chuck
from the gate. Turn the key
clockwise to draw the teeth of
the chuck inward and release it from the gate.
TIP: Using the 5/16 nch hex
wrench and loosening the
bottom 2 bolts on the front plate
directly below the chuck may
make the chuck transfer process
much easier.
Step 2: As a recommendation, we urge
you to degrease the rail and wipe it down
with a rag to remove any unnecessary
shipping grease before sliding the chuck
on. This will make the transfer process
easier and keep your machine running as smooth as
possible.
p.9
Step 3: With the help of another person,
slowly slide the chuck onto the new rail
making sure to support the new rail from
the tail end. The tail should not wobble or
raise up off the ground during this step.
Step 4: If you have loosened
the bottom plate on the chuck
as mentioned in the previous
tip, use the 5/16 nch hex
wrench to tighten the bottom
bolts now.
Step 5: Using the ratchet, 8
nch socket extens on and 3/4
nch socket, remove the bolts
on both sides of the machine
where the stock rail meets the
inside of the face plate. Do this to prepare it for
removal and replacement. You may also need a
3/4 nch wrench to secure the nuts from inside
the rail as you remove the bolts. Be sure to support the
stock rail as it will become loose.
p.10
Assembl ng the Mach ne
Step 1: With the machine in multiple
sections, remove the stock rail (set
aside) and install the new plast c cha n
gu de block. Loosely affix the guide
block to the rail end nearest the front
of the machine using the nuts and bolts
provided. NOTE: You w ll have to
reach a wrench ns de the ra l to
ach eve th s.
Step 2: Align the center of the guide block with the inner
chain gear then tighten the 2 bolts of the block.
Step 3: Now, use the hand
truck (or the help of another
person) to move the head of
the machine toward the new
rail. Then, insert the bare end
into the rail slot on the head.
There should be a small gap between
the chain guide block (from the
previous step) and the sprocket in front
of it (attached to the machine head).
Autres manuels pour Dragon
1
Table des matières
Autres manuels Bend-Tech Équipement industriel
Bend-Tech
Bend-Tech Dragon A400 Guide d'installation
Bend-Tech
Bend-Tech Dragon A400 Manuel d'installation et d'exploitation
Bend-Tech
Bend-Tech Dragon A400 Manuel utilisateur
Bend-Tech
Bend-Tech DRAGON A150 Manuel utilisateur
Bend-Tech
Bend-Tech Dragon mAchines Manuel utilisateur
Bend-Tech
Bend-Tech Dragon A400 Guide d'installation
Bend-Tech
Bend-Tech Dragon A400 Manuel utilisateur
Bend-Tech
Bend-Tech Dragon A400 Manuel utilisateur
Bend-Tech
Bend-Tech Dragon A400 Manuel utilisateur
Bend-Tech
Bend-Tech Dragon mAchines Manuel utilisateur
