Benchmark Orbi-Shaker CO2 Manuel utilisateur

Operations Manual

Index:

I. General Information

II-1. Introduction

II-2. Installation

II-3. Specifications

II-4. Features

III-1. Operation

III-2. Platform Installation

III-3. Error Messages

III-4. Maintenance

IV-1. Service and Contact

I. General Information

NOTE : Before operating the Orbi-Shaker CO

₂

please take a few

minutes to familiarize yourself with the contents of this manual.

Thank you for purchasing the Orbi-Shaker CO₂. This operations

manual contains instructions for the care of this Instrument. In order

to use the instrument properly, please read this manual carefully

before operation. Please keep it available for future use.

Prior to the initial operation:

Please check the Instrument and the accessories against the packing

list when you first open the shipping carton. If you find there is

damage, a discrepancy, or missing items, please contact your

supplier immediately.

II-1. Introduction

The Orbi-Shaker CO₂is designed for use in extreme environments,

including CO₂incubators. The product is ideal for many applications used

in general research laboratories, including cell culture, bacteria suspension,

etc.

The Microprocessor’s constant monitoring system ensures accurate

shaking speed. The beltless drive system minimizes noise and vibration

while increasing the life span of the unit.Optional accessories are

available for compatibility with a wide variety of laboratory vessels,

including flasks, tubes, dishes and trays.

II-2. Installation

-Choose a location for the shaking mechanism.

-To assure proper ventilation, allow a minimum of 2 inches (5 Cm) of the

clearance between the rear and side of the unit and the adjacent wall.

-Always ensure that the machine is installed on a level surface.

-Once the machine is placed in the desired location, attach the flat cable

to the remote controller.

-Place the remote controller in the desired location.

(Ensure that the remote controller is located in a dry area)

-Before plugging the remote controller into the outlet, ensure that the

electrical specifications (listed on the serial number label on the rear

side of the controller) matches the electrical specifications of your outlet.

-ALWAYS: Connect the flat cable from the remote controller to the

shaking mechanism before connecting the controller to the

electrical outlet.

When installing the instrument inside of an incubator, typically, the

flat cable can exit the incubator through a cable port (usually located

on the back of the incubator). If your incubator does not include a

port, the flat cable is designed so that it can also exit between the

front of the door and the chamber without preventing sealing.

II-3. Specification

1) Dimension (Exterior) : 30 (W) X 34 (D) X 11.8 (H) cm

/ 11.8 (W) x 13.5 (D) x 3.5 (H) in.

(Platform): 30 (W) x 33 (D) cm

/ 12 (W) x 13 (D) in.

2) Speed range : 30 - 300 RPM

(No load & on stable surface)

3) Shaking Orbit: 19mm (3/4”)

4) Timer : Digital - 1 min. to 47hr 59min.

(1 min. increments)

Or continuous

5) Motor : Brushless DC - Beltless

6) Weight: Shaker: 25 lbs / 11.5 kg

Controller: 5 lbs / 2.3 kg

7) Electrical: 120V or 230V, 50-60Hz

/ 600W

8) Operating Environment: 0 to 65℃

II-4. Features

1) Constant Monitoring System (CMS) ensures precise control

over speed

2) Sealed shaking mechanism for use in extreme environments

(humidity up to 100%)

3) Controller allows for speed/time adjustment without opening door when it

is used in an Incubator or a chamber.

4) MAGic Clamp platform available as optional accessory.

5) Blushless DC motor and beltless drive system minimizes

noise and vibration.

6) Digital controller displays speed and time.

7) Wide variety of optional accessories available for most

common laboratory vessels

III-1. Operation

3.1.1 Basic View Screen

▶Basic View Screen

ⓐRUN LED: indicates if the shaker is running.

ⓑTime setting: Indicates the set or remaining time.

(To adjust, TOUCH the time value)

ⓒRPM setting: Displays the set or current RPM

(To set the desired shaking speed, TOUCH the RPM value)

ⓓAlarm Mute : The audible alarm can temporarily deactivated by TOUCHING

the key when the audible alarm is active (beeping). This silences/mutes

the alarm for 10 minutes and the icon is displayed as . Following the 10

minute mute, if alarm event continues, audible alarm is unmuted.

To unmute the alarm, TOUCH the key to toggle to the unmuted

setting, .

Alarm Disabled : The alarm can be disabled by TOUCHING and holding

the key for 3~5 seconds. To reactivate the alarm setting, TOUCH the

OFF

once.

ⓔMenu: TOUCH to activate the main menu

ⓕShaker Start/Stop Button

TOUCH to start or to stop the shaker.

ⓖShaker end: Indicates that the setting time has expired and the

shaker stops running.

▶Booting

Press the power switch into the ON position, the display

illuminates and the booting screen is displayed for 2

seconds before showing the “Basic View” screen.

NOTE: If the shaker has been powered off before the

completion of a run, the unit will automatically power on to

the previous settings.

▷RPM setting change

ⓐTOUCH the RPM value, The numbers become red

ⓑ“SET MODE” is displayed (flashes)

ⓒInput the desired value by pressing UP(▲)/DOWN(▼) buttons

NOTE: Press and hold the buttons to increase or decrease the value

quickly.

ⓓApply: To store the newly set value TOUCH

(Or wait 5 seconds for the value to store automatically)

ⓔExit: If you press after changing any values, the values are not

saved and the screen returns to the previous screen

ⓓ

ⓑ

ⓒ

ⓔⓕ

SHAKER END

ⓖ

ⓐ

ⓑ

ⓒ

ⓓ

ⓔ

▷Time setting change

ⓐTOUCH the time value, The numbers become red

ⓑ“SET MODE” is displayed (flashes)

ⓒInput the desired value by pressing UP(▲)/DOWN(▼) buttons

NOTE: Press and hold the buttons to increase or decrease the value

quickly.

ⓓApply: To store the newly set value TOUCH

(Or wait 5 seconds for the value to store automatically)

ⓔExit: If you press after changing any values, the values are not

saved and the screen returns to the previous screen

NOTE: The time cannot be adjusted during a run. To change the time

during a run, you must TOUCH . Change the time value and

press and

3.1.2. Advanced View Screen

▶Advanced Mode

To switch from the standard BASIC view

To the ADVANCED view,

TOUCH “MENU” and choose ADVANCED View.

NOTE: To return to the BASIC View, TOUCH

“MENU” and choose the BASIC View.

The ADVANCED View provides the user with access to the

STEP mode for linking consecutive mixing cycles.

BASIC to ADVANCED

ADVANCED to BASIC

▶Shaker setting (Advanced)

▷RPM setting change

ⓐTOUCH the RPM Shaker value, the screen turns to the

Shaker setting screen

ⓑTOUCH the “RPM Set” Value to adjust the set speed.

ⓒInput the desired value by using the key pads in

the setup screen

ⓓApply: When you press , the changed

setting values are saved and the screen turns to

the previous screen

ⓔExit: If you press button, the changed setting

values are not saved and the screen turns to the

previous screen

ⓕThe RPM setting range is 30~300rpm

When entering a value out of this range and

pressing , the message

“Incorrect range” is displayed.

ⓐ

ⓑ

ⓒ

ⓓ

ⓔ

ⓕ

ⓐⓑ

ⓒⓓⓔ

▶Shaker setting (Advanced ONLY)

▷Alarm setting change

The alarm value is the difference between

the set speed and the measured (displayed)

speed. If the difference exceeds this value

(once the temperature has been reached) the

alarm will trigger.

ⓐTOUCH the RPM Shaker value, the screen turns

to the Shaker setting screen

ⓑTOUCH the “Alarm Set” Value to set the timer

ⓒInput the desired value by using the key pads

in the setup screen

ⓓApply: When you press , the changed

setting values are saved and the screen turns to

the previous screen

ⓔExit: If you press button, the changed setting

values are not saved and the screen turns to the previous

screen

ⓕThe RPM setting range is 1~30rpm

When selecting the value out of this range and

pressing , the message “Incorrect range” is

displayed.

▷Alarm Mute

The audible alarm can temporarily deactivated by TOUCHING the key

when the audible alarm is active (beeping). This

silences/mutes the alarm for 10 minutes. and the icon is displayed as

. Following the 10 minute mute, if alarm event continues,

audible alarm is unmuted.

To unmute the alarm, TOUCH the key to toggle to the

unmuted setting, .

▷Alarm Disabled

The alarm can be disabled by TOUCHING and holding

the key for 3~5 seconds. To reactivate the alarm

setting, TOUCH the once.

OFF

BASIC View ADVANCED View

OFF

ⓑ

ⓒ

ⓓ

ⓔ

▶Shaker setting (Advanced)

Adjusting the Shaking Time

ⓑTOUCH the “Time Set” Value to adjust the set shaking

time.

ⓒInput the desired value by using the key pads in the

setup screen

ⓓApply: When you press , the changed

setting values are saved and the screen turns to the

previous screen

ⓔExit: If you press button, the changed setting

values are not saved and the screen turns to the

previous screen.

ⓐ

ⓑ

ⓒ

ⓓ

ⓔ

ⓕ

3.1.3. Shaker Step Setting

▷

RPM, time setting

ⓐTOUCH the RPM Shaker value to enter the shaker setup screen.

ⓑSelect , the screen moves to the shaker step & setup screen

Choose each of the 4 desired speeds by pressing on the speed value.

(If less than 4 linked speeds are desires,

leave the time and speed values as “0” to skip.)

ⓓOnce a RPM step is selected, use the keypad in the setup screen

to select the desired RPM value

ⓔApply: When you press , the changed setting values are saved

and the screen turns to the previous screen

ⓕExit: If you press button, the changed setting values are not saved

and the screen turns to the previous screen

ⓖOnce the desired RPM speeds have been chosen,

adjust the time values by following the same steps.

ⓗThere are 3 modes available for Step Operation :

“One cycle”, “Repeat Cycle”, “Step off”

NOTE: Repeat cycle will result in continue repeating of all programmed steps

until the stop button is pressed.

ⓐ

ⓓ

ⓔ

ⓕ

ⓒⓖ

ⓗ

ⓑ

Autres manuels pour Orbi-Shaker CO2

Ce manuel convient aux modèles suivants

Autres manuels Benchmark Équipement de laboratoire

Benchmark

Benchmark TC 9639 Manuel utilisateur

Benchmark

Benchmark MyBath B2000-2 Manuel utilisateur

Benchmark

Benchmark Orbi-Shaker Manuel utilisateur

Benchmark

Benchmark R4040 Manuel utilisateur

Benchmark

Benchmark MyBath B2000-2 Manuel utilisateur

Benchmark

Benchmark Orbi-Shaker Manuel utilisateur

Benchmark

Benchmark BSH1001 Manuel utilisateur

Benchmark

Benchmark H2020 Manuel utilisateur

Benchmark

Benchmark Orbi-Shaker CO2 Manuel utilisateur

Benchmark

Benchmark R2020 Manuel utilisateur

Benchmark

Benchmark Micro Bead Sterilizer B1201 Manuel utilisateur

Manuels Équipement de laboratoire populaires d'autres marques

Qiagen

Qiagen DML 3000 Manuel utilisateur

Queensgate

Queensgate NANOSCAN OP400 Manuel de programmation

Conviron

Conviron GEN1000-GE Manuel utilisateur

Parr Instrument

Parr Instrument 4560 Mode d’emploi

IKA

IKA IC control Manuel utilisateur

Integra

Integra DOSE IT Manuel utilisateur

Agilent Technologies

Agilent Technologies 5800 ICP-OES Manuel utilisateur

Endress+Hauser

Endress+Hauser Cleanfit CPA875 Manuel utilisateur

NI PXI-5422 Manuel

Collomix

Collomix Aqix Manuel utilisateur

SPEX SamplePrep

SPEX SamplePrep 6875 Freezer/Mill Series Manuel utilisateur

Ocean Insight

Ocean Insight FLAME-NIR+ Manuel utilisateur

Parker

Parker ALIGN-MG-NA Manuel utilisateur

BD 644787 Manuel utilisateur

DENTAURUM

DENTAURUM Compact Megaplus Manuel utilisateur

Biuged Laboratory Instruments

Biuged Laboratory Instruments BGD 626 Manuel utilisateur

VWR

VWR SAS Super IAQ Manuel utilisateur

illumina

illumina MiSeqDx Manuel utilisateur