Beluk CX plus Manuel utilisateur

MB_EN_ACXplus-R_BEL_02

Beluk GmbH

Tel.: +49 8861 2332 0

Taubenstrasse 1

Fax: +49 8861 2332 22

86956 Schongau

blr@beluk.de

Germany

http://www.beluk.de

CX plus Operating Manual

General safety notes

Failure to observe the following instructions can lead to serious

injury or death !

During installation, there is a risk of electric shock. For this reason,

electrical devices may only be installed, operated, serviced and maintained

by qualified personnel. A qualified person is one who has the ability,

experience and knowledge necessary for the construction, installation and

operation of electrical equipment and is trained in the detection and

prevention of potential hazards.

During installation and maintenance, the relevant regulations for

installation of switchgear and for preventing accidents must be observed

and complied with.

Devices with damaged or open housings or terminals may not be

connected to the mains and must be disconnected immediately.

After disconnection of the device, wait for 10 minutes until the capacitors

are discharged before removing doors or covers. After that, check to

ensure that the compensation system has been de- energised.

Beluk GmbH assumes no responsibility or liability for injury to persons or

damage to equipment due to improper installation or installation not for

the intended use carried out by qualified personnel.

New features of the CX plus over the BLR- CX

Modbus: no longer as an external add- on module,

now optionally installed internally.

Alarm memory: enables the storage of the last 10 alarms

New alarms: THD I alarm

I-Low alarm: can be disabled via digital input now:

SETUP/ 500/ 518 → “YES” = I-Low alarm blocked

Control algorithm: in addition to LIFO, AUTOMATIC (best fit) and

PROGRESSIVE, the FIFO algorithm has now also been implemented

Outputs: 6 or 12 stages, separate fan relay (can be used as 7th /13th

stage)

Display: to extend the service life of the backlight, it is turned off

60 seconds after last usage.

Storage Umax and THD Umax

Digital input:

Choice between target cosϕ1 and target cosϕ2, signalisation of an

external alarm or to disable the I-Low alarm

Temperature sensor: NTC now internal.

Installation and commissioning:

1) Before installation, the connection data of the CX plus must be

compared with the data of the supply network and the installation.

2) The working area must be disconnected from voltage and secured

against unauthorised and unintentional restart. The absence of

voltage must be verified with a standardised instrument/ testing

device. The voltage- free system must be grounded and short-

circuited. Adjacent live parts must be covered or placed behind

barriers.

3) The current transformer must be short-circuited! A current

transformer that has NOT been short-circuited generates very high

voltages posing a danger to persons and equipment. The current

transformer can thereby be destroyed.

4) Disconnect and remove the old reactive power controller.

5) Plug the CX plus into the switch panel section and fix it with the two

mounting brackets. (Section 138 x 138 mm)

6) Connect the protective conductor to the PE terminal of the metal

back of the CX plus.

7) Connect the connecting lines as shown in the wiring diagram.

(Current transformer: K [power plant] to S1, L [load] to S2)

8) Remove current transformer jumper.

9) Switch on voltage.

10) With a proper connection and correct connection data, the LCD lights

and the LCD test is active for 1 second.

11) Activation of user-guided initial commissioning “FIrSt SEtUP“ after

confirming “YES“. Afterwards all required parameters are requested

by CX plus. The choice of “NO” requires, that the user implements the

following parameters (12) … 15)) manually.

12) The current transformer factor (Ct) must be entered.

13) The nominal voltage (Un) and the voltage transformer factor (Pt)

must be entered, too.

14) Start the “Automatic initialisation” (AI) or enter the Phaseoffset

(PO) manually.

15) If the „Automatic initialisation” was successfully finished, the

message “AUTO”appears on the LCD.

Control starts after the discharge time lock.

Questions during commissioning:

1) No AUTO display → control stopped

Reasons: Manual operation, control is switched off, temperature is

too high, current is less than 15 mA, voltage or THD of voltage are not

permitted

2) U ALARM display → voltage out of tolerance

Check settings for rated voltage (SETUP/ Un) and

voltage transformer (SETUP/ Pt)

3) I Lo ALARM display → no current flow

Possible causes: Connection from the current transformer to

the controller is not correct; current transformer

jumper is not removed; transformation ratio is too large; no current

4) EXPORT display → feeding back of active power

If there is no real feeding back, connect voltage and

check current (phase polarity)

→ section Incorrect connections/ AI –automatic initialisation

5) Incorrect Cos phi → incorrect connection

Connect voltage and check current (phase, polarity)

→ section Incorrect connections/ AI –automatic initialisation

6) Outputs are switched off again immediately

→ section Incorrect connections/ AI –automatic initialisation

7) Frequent switching of the outputs

→output of the capacitors first needs to be detected

Display:

INFO: Stage database

AUTO: Automatic operation

MANUAL: Manual operation

SETUP: Settings menu

ALARM: Alarm memory

EXPORT: Feeding back of active power

NT: 2nd target cosϕis active

ALARM: Flashes if there is an

alarm notification

1st line:

I) cos ϕ/ menu items

II) inductive/ capacitive

2nd line:

I) code of metered and set values

II) metered and set values/ alarm

codes

III) units

Stage display:

Status of the stage (on/ off)

Stage faulty (flashing)

III

Operation:

The controller is operated using 4 keys.

Increase values

Select menu items

Exit menus/ Esc

Cursor to the left

Reset alarm (5 sec.)

Opens menus/ Enter

Cursor to the right

Settings

Decrease values

Select menu items

Input parameters:

↑, ↓

→

↑, ↓

→

←

Digit adjust (up/ down)

Move to next position

After the last digit is set, selection of:

- Multiplier k(kilo) or M(Mega)

- Preceding sign i(inductive) or c(capacitive) (flashing of i or c)

Application of values at the end

Abort entry

Main menu:

Select menu items with ↑, ↓, enter the submenu with →

Measurement value display:

(Change with ↑, ↓)

ULL, ULN, I, P, Q, ΔQ, S, THD U, 3.-19. Har. U,

THD I, 3.-19. Har. I, cosϕ, PF, APF, Hz(F), t(°C),

thi (°C), OPh (h), tanϕ, U hi, THD U hi

INFO stage database:

Power and power loss of stages, number of

switching operations, stage type, operating hours.

(→ section INFO stages database)

MANUAL operation:

Intentional switching on and off of

switching outputs.

(→ section MANUAL operation)

SETUP settings menu:

Rated voltage (Un), current transformer (Ct),

voltage transformer (Pt), automatic initialisation

(AI), control on/ off (PFC), target cosϕ1 (CP1),

switching time (St), stage type (Out)

(→ section SETUP settings menu)

ALARM memory:

Memory buffer shows the last 10 alarms. The most

recent alarm is in the first position.

Autres manuels pour CX plus

Table des matières

Autres manuels Beluk Contrôleurs

Beluk

Beluk BLR-CM 3 phase Manuel utilisateur

Beluk

Beluk BLR-Q(U)06/12R Manuel utilisateur

Beluk

Beluk BLR-CX-R Manuel utilisateur

Beluk

Beluk BLR-CM Manuel de formation

Beluk

Beluk BLR-CX Manuel d'installation et d'exploitation

Beluk

Beluk BLR-CM Modbus Mode d’emploi

Beluk

Beluk CX plus Manuel utilisateur

Beluk

Beluk CX plus Manuel utilisateur

Beluk

Beluk BLR-CX Manuel utilisateur

Beluk

Beluk CX plus Manuel utilisateur

Manuels Contrôleurs populaires d'autres marques

Digiplex

Digiplex DGP-848 Mode d'emploi

YASKAWA

YASKAWA SGM series Manuel utilisateur

Sinope

Sinope Calypso RM3500ZB Manuel utilisateur

Isimet

Isimet DLA Series Style 2 Manuel d'installation

LSIS

LSIS sv-ip5a Manuel utilisateur

Rockwell Automation

Rockwell Automation 1769-L31 Manuel utilisateur

Airflow

Airflow Uno hab Manuel utilisateur

ABB

ABB ACS580-01 drives Manuel utilisateur

Panasonic

Panasonic GM1 Series Manuel utilisateur

Emerson

Emerson SW93 Manuel utilisateur

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuel utilisateur

Panasonic

Panasonic FP? Positioning Unit RTEX Manuel utilisateur

Samson

Samson Type 5824 Manuel de service

Alpha IP

Alpha IP MIOB 21001 Manuel utilisateur

Siemens

Siemens OpenAir GMA 1 Series Manuel utilisateur

Surecom

Surecom SR-629 Manuel utilisateur

Fishman

Fishman TriplePlay Manuel utilisateur

Regulus

Regulus SRS1 T Manuel utilisateur