Belson ESI-12F Instructions d'installation

FULL ONE-YEAR WARRANTY

Applica warrants this product against any defects that are due to

faulty material or workmanship for a one-year period after the

original date of consumer purchase. This warranty does not

include damage to the product resulting from accident or misuse.

If the product should become defective within the warranty period,

we will repair it or elect to replace it free of charge.

This warranty gives you specific legal rights and you may also

have other rights which vary from state to state or province to

province. Answers to any questions regarding warranty or service

locations may be obtained by calling Consumer Assistance and

Information: 203-926-3230.

Printed in Hong Kong

2001/2-15-87 ESI-8F

ESI-12F

PROFESSIONAL

FLAT STOVE IRON

SAVE THIS USE AND CARE BOOK

PROFESSIONAL USE ONLY

2001_2_15_87_BP 3/5/01 4:04 PM Page 1

OPERATING INSTRUCTIONS

PRODUCT MAY VARY SLIGHTLY FROM ILLUSTRATION

Heat-resistant

rotating handles

Closed end for

consistent, even

heat distribution

High-quality steel

barrel holds heat longer

TO USE:

1. Insert iron into heater stove and heat for 1 to 3 minutes,

depending upon the strength of the curl you desire and the type

and texture of hair it is used on.

CAUTION: After initial heating to remove oil, do not allow iron to

heat for more that 3 minutes. The extreme heat may damage hair.

If iron is heated for more than 3 minutes, do not use; remove it and

let it cool. (Time may vary due to barrel size and number of irons

heated at one time. Test iron on a small section of hair before

using.)

2. For styling, section hair into strands of not more than 1 inch deep

and 2 inches wide.

3. Keep the hair strand smooth by brushing or combing through the

section while holding the ends taut with the other hand.

4. Taking one section at a time, place the ends of hair under the

barrel with the clamp open. Then close the clamp making sure

that the ends extend just a tiny bit beyond the clamp.

5. Keep the section of hair taut as you wind it around the hot barrel

by turning the handle. Wind the curl toward scalp as far as you

wish to go without touching scalp with the hot barrel.

6. When you are ready to release curl, unwind about half a turn

(for longer hair, unwind a bit more) and open the clamp.

7. Now, gently withdraw the barrel from the center of curl.

8. Allow curl to cool, and try not to disturb curls as you proceed

in the same manner around whole head.

STYLING TIP: For bouncy, flip-up curls, the clamp should be under

and the barrel over the section of hair at the start of curl. For curl-

under, page-boy styles, the clamp should be over and the barrel

under the hair section at the start of curl.

WARNING: Due to the extreme heat capabilities of this iron, extra

care should be taken when using.

IMPORTANT:

This iron has been coated with a special oil to temper the barrel

and protect it during shipping. When heating for the first time,

preheat iron 4 to 5 minutes. You will notice some smoke and a slight

odor. This is normal and will quickly disappear.

2001_2_15_87_BP 3/5/01 4:04 PM Page 2

Ce manuel convient aux modèles suivants

Autres manuels Belson Fer à coiffer

Belson

Belson PR2011C Instructions d'installation

Belson

Belson MH5010 Instructions d'installation

Belson

Belson DS-678ISN/1 Instructions d'installation

Belson

Belson DS-26 Instructions d'installation

Belson

Belson C11-10 Instructions d'installation

Belson

Belson DS-78 Instructions d'installation

Belson

Belson MH2013 Instructions d'installation

Belson

Belson MH5011 Instructions d'installation

Belson

Belson C18-I-6C Instructions d'installation

Belson

Belson RCI-4-15 Instructions d'installation

Belson

Belson TS-10F-1 Instructions d'installation

Belson

Belson SC-02 Instructions d'installation

Belson

Belson CM2012 Instructions d'installation

Belson

Belson DS-26TN Instructions d'installation

Belson

Belson C23-I-4 Instructions d'installation

Belson

Belson TS-10S-1 Instructions d'installation

Belson

Belson CC7596RV Instructions d'installation

Belson

Belson MH2021 Instructions d'installation

Belson

Belson RCI-10-15 Instructions d'installation

Belson

Belson C22-I-12 Instructions d'installation

Belson

Belson C-315AR Instructions d'installation

Belson

Belson ESI-10 Instructions d'installation

Belson

Belson C-335A Instructions d'installation

Belson

Belson CM2008 Instructions d'installation

Manuels Fer à coiffer populaires d'autres marques

Vitek

Vitek VT-2505 Manuel utilisateur

Morphy Richards

Morphy Richards IB22063 Fiche d'information produit

TZS First AUSTRIA

TZS First AUSTRIA Ida FA-5670-3 Manuel utilisateur

izzy

izzy LN-112 Manuel utilisateur

Vitek

Vitek VT-2310 Manuel utilisateur

Okoia

Okoia HS23 Manuel utilisateur

Arzum

Arzum TRENDCARE AR 5042 Manuel utilisateur

SOLAC

SOLAC PP7251 Manuel utilisateur

VS Sassoon

VS Sassoon VSLE330A Manuel utilisateur

Philips

Philips HP8339 Manuel utilisateur

Philips

Philips HP4666 Manuel utilisateur

Vitek

Vitek VT-8291 Manuel utilisateur

VS Sassoon

VS Sassoon miniPRO Wave Envy Manuel utilisateur

Arzum

Arzum SUPERSTAR TOUCH Manuel utilisateur

Remington

Remington S2880ZBA Manuel utilisateur

cecotec

cecotec Bamba RitualCare 900 Wet&Dry Max Manuel utilisateur

Philips

Philips HPS950 Manuel utilisateur

Andis

Andis Gold CSI-1E Manuel utilisateur