Bellini BCA64GK Manuel utilisateur
USER MANUAL
Ceramic Hob
Model No. BCA64GK
V2 July 2022
GSM Retail Australia Pty Ltd ABN: 53 007 582 475Lt
For Warranty and technical queries: Australia 1300 373 199
For Warranty and technical queries: New Zealand 0800 764 912
www.belliniappliances.com.au
Thank you.
Thank you for choosing Bellini Appliances.
Bellini appliances carry a 3 year in home warranty, be sure to
retain your user manual and receipt.
For all warranty and technical queries please phone:
Australia 1300 373 199
New Zealand 0800 764 912
GSM Retail Australia Pty Ltd ABN: 53 007 582 475
For Warranty and technical queries: Australia 1300 373 199
For Warranty and technical queries: New Zealand 0800 764 912
www.belliniappliances.com.au
Contents
Safety instructions …………….............................. 4 - 6
Installation ……………………............................... 6 - 10
Description of the Ceramic Hob surface layout ... 10 - 13
Using the ceramic hob ………………………......... 13 - 17
Hob guidelines …………………………………....... 17 - 18
Maintenance and cleaning ………………………… 18 - 19
Environmental note ………………………………… 20
3
Safety instructions
This User Instruction Manual contains important information, including safety &
installation points, which will enable you to get the most out of your appliance.
Please keep it in a safe place so it is easily available for future reference; for you or
any person not familiar with the operation of the appliance.
Caution!
Do not use the ceramic hob until you
have read this instruction manual.
The ceramic hob is intended for
household use only.
The appliance becomes hot during
operation. Take care not to touch the
hot surface.
Always keep children away from the
ceramic hob.
While in operation, direct contact with
the ceramic hob may cause burns!
Ensure small items of household
equipment, including connection
leads, do not touch the hob as the
insulation material of this equipment is
usually not resistant to high
temperatures.
Do not leave the ceramic hob
unattended when frying. Oils and fats
may catch fire due to overheating or
boiling over.
Do not switch on the hob until a pan
has been placed on it.
Do not put pans weighing over 25kg
on the hob.
Do not use the ceramic hob in the
event of a technical fault. Any faults
must be fixed by an appropriately
qualified and authorised person.
In the event of any incident caused by
a technical fault, disconnect the power
and report the fault to the service
centre to be repaired.
The rules and provisions contained in
this instruction manual should be
strictly observed. Do not allow
anybody who is not familiar with the
contents of this instruction manual to
operate the ceramic hob.
The ceramic hob should not be
cleaned using steam cleaning
equipment.
IMPORTANT: The adjacent furniture
or housing and all materials used in
the installation must be able to
withstand a minimum temperature of
95°C above the ambient temperature
of the room it is located in, whilst in
use.
Any damage caused by the appliance
being installed in contravention of this
temperature limit, or by placing
adjacent cabinet materials closer than
4mm to the appliance, will be the
liability of the owner.
Child Safety
We strongly recommend that
babies and young children are
prevented from being near to the
appliance and not allowed to touch
the appliance at any time.
If it is necessary for younger family
members to be in the kitchen,
please ensure that they are kept
under close supervision at all times.
4
General Safety
This appliance is not intended for
use by persons (including children)
with reduced physical, sensory or
mental capabilities, or lack of
experience and knowledge, unless
they have been given supervision
or instruction concerning use of the
appliance by a person responsible
for their safety.
Children should be supervised to
ensure that they do not play with
the appliance.
NEVER try to extinguish a fire with
water, switch off the appliance and
then cover flame e.g. with a lid or a
fire blanket.
WARNING: Danger of fire - do not
store items on the cooking
surfaces.
Means for disconnection must be
incorporated in the fixed wiring in
accordance with the wiring rules.
Do not allow electrical fittings or
cables to come into contact with
areas on the appliance that get hot.
Do not use the appliance to heat
the room it is located in or to dry
clothing.
Do not install the appliance next to
curtains or soft furnishings.
If the supply cord is damaged, it
must be replaced by the
manufacturer, its service agent or
similarly qualified persons in order
to avoid a hazard.
The appliance is not intended to be
operated by means of an external
timer or separate remote-control
system.
Power cord can’t be accessible
after installation.
This product can be worked but not
through outside timer and remote
control.
Warning: If the surface is cracked,
switch off the appliance to avoid the
possibility of electric shock, for hob
surfaces of glass, ceramic or similar
material which protect live parts.
Warning: a steam cleaner is not to
be used.
CAUTION: The cooking process has
to be supervised. A short term
cooking process has to be
supervised continuously.
WARNING: Unattended cooking on
a hob with fat or oil can be
dangerous and may result in a fire.
This appliance should be connected
to a circuit which incorporates an
isolating switch which can be
accessible by the user after
installation providing full
disconnection from the power
supply. The disconnection may be
achieved by incorporating a switch
in the fixed wiring in accordance
with the wiring rules.
Warning: Before obtaining access to
terminals, all supply circuits must be
disconnected.
WARNING: Use only hob guards
designed by the manufacturer of the
cooking appliance or indicated by
the manufacturer of the appliance in
the instructions for use as suitable
or hob guards incorporated in the
appliance. The use of inappropriate
guards can cause accidents.
WARNING: The appliance and its
accessible parts become hot during
use.
5
Care should be taken to avoid
touching heating elements.
If a stationary cooktop is not
provided with a supply cord and a
plug or by other means of
disconnection from the supply
having an air gap contact the
separation in all active (phase)
conductors, the instructions shall
state that such means for
disconnection shall be incorporated
in the fixed wiring according to the
wiring rules.
Installation
IMPORTANT: The appliance must be installed by a qualified technician
according to the current local regulations and in compliance with the
manufacturer's instructions.
Electrical connection
Before connecting the appliance, make sure that the supply voltage marked on
the Rating Plate corresponds with your mains supply voltage.
WARNING: THIS APPLIANCE MUST BE EARTHED.
The kitchen area should be dry and aired and equipped with efficient ventilation.
When installing the ceramic, easy access to all control elements should be ensured.
This is a Y-type design built-in ceramic, which means that its back wall and
one side wall can be placed next to a high piece of furniture or a wall. Coating
or veneer used on fitted furniture must be applied with a heat-resistant
adhesive (min. 95°C).This prevents surface deformation or detachment coating.
The cooktop should be installed according to the manufacturer’s instructions.
Installation of ceramic hob:
Make an opening with the dimensions given in
the diagram for the hob to be mounted on the
worktop.
Check seal for perfect fit and overall cover.
Lower the ceramic hob into place and align
correctly.
Using a standard screwdriver, tighten the
tension clamps evenly starting at the centre and
moving diagonal, until the built-in rim is tight on
the worktop.
6
Preparing the unit for a built-in appliance
WARNING
The appliance can be installed on a work surface with a thickness of between 30
and 40 mm and rear of the appliance should be ≥40mm away from the wall and
kept ≥100mm away from the side of the work surface.
Carry out all cutting of the unit and work surface then carefully remove shavings
or sawdust before inserting the appliances.
To ensure a correct ventilation of the hob, please comply with the dimensions
shows in figures.
Always refer to the manufacturer for specific instructions.
Make sure the surface is level and square and that no part interferes with the space
required for installation.
Prepare the cut as indicated (see installation dimensions).
Installing the hob
7
Remove the material and envelope of documents from the packaging.
Before proceeding with installation, read the work instructions carefully.
Step.1
Put a towel or cloth on the work surface. Place the hob face
down on the protected surface.
Step.2
Apply the strip seal, supplied with the hob, which is for sealing it
onto the work surface.
Do not use silicone. Apply the seal to the edge of the bottom of
the hob, leaving about 3mm from the edge of the glass.
Apply the seal all around the circumference.
Cut any excess and bring the two ends of the seal together so
they match.
Step.3
Fix the brackets (4 pcs) on the front side and rear side by screw. Put the hob in the
cut-out cabinet, and make it centered. Ensure that the front edge of the hob is parallel
to the side edge of the work surface.
IMPORTANT: You must observe the ventilation requirements
shown in the drawing opposite.
IMPORTANT: There are ventilation holes around the outside
of the hob. YOU MUST ensure that these holes are not
blocked by the work top, when you put the hob into position
(see drawing opposite).
IMPORTANT: Do not use a silicon sealant to seal the
appliance against the aperture. This will make it difficult to
remove the hob from the aperture in future, particularly if it
needs to be serviced.
Carefully turn the hob back over and then gently lower it into
the aperture hole that you have cut out.
8
Fitting guidelines
The ceramic hob is manufactured to work with two-phase alternating
current (400V2N~50Hz). The voltage rating of the ceramic hob heating
elements is 230V. Adapting the ceramic hob to operate with one-phase
current is possible by appropriate bridging in the connection box
according to the connection diagram below. The connection diagram is
also found on the cover of the connection box. Remember that the
connection wire should match the connection type and the power
rating of the ceramic hob.
The connection cable must be secured in a strain-relief clamp.
Warning!
Remember to connect the safety circuit to the connection box terminal marked with
The electricity supply for the ceramic hob must have a safety switch which enables the
power to be cut off in case of emergency. The distance between the working contacts of
the safety switch must be at least 3mm. Before connecting the ceramic hob to the power
supply it is important to read the information on the data plate and the connection
diagram.
Wires for each ceramic cooktop
model
Adaptive voltage range and wires The wiring diagram
220-240
1N～ 50-60Hz
380-420
2N～ 50-60Hz KADO K 1/5
BCA64GK H05VV-F 3G2.5 H05VV-F 4G2.5
2
1
9
-The cable connections must be in accordance with the diagram located on the bottom of the hob.
-The cable type must be connected to the corresponding power supply terminal box.
-You should use a good quality screwdriver to carefully, fully tighten all of the terminal screws.
-If when the hob is first switched on, only two of the zones work, you should recheck that the
terminal screws are all fully tightened. This should be done before contacting the Customer Care
Department.
-IMPORTANT: The appliance must NOT be connected to the mains supply by means of a 13A
plug and socket.
-This appliance must be wired into a 30A double pole switched fused spur outlet, having 3 mm
contact separation and placed in an easily accessible position adjacent to the appliance. It should
not be located above the appliance and no more than 1.25m away from it.
-The cable can be looped if necessary, but make sure that is not kinked or trapped when the hob
is in position. Care must be taken to avoid the cable being in contact with hot parts of the
appliance.
Replacing the mains supply cable
If the mains supply cable is damaged, then it must be replaced
appropriately.
The mains supply cable should be replaced in accordance with the
following instructions:
Switch the appliance off at the control switch.
Open the terminal block on the underside of the hob.
Unscrew the terminal screws fixing the cable.
The “green-yellow” earth wire must be connected to the terminal
marked . It must be about 10 mm longer than the live and neutral
wires.
The “blue” neutral wire must be connected to the terminal marked
with letter (N)
- the live wire (L1) must be connected to the terminal marked with
letter (L1)(220-240V 1N～).
The “blue” neutral wire must be connected to the terminal marked
with letter (N)
- the live wire L1 must be connected to the terminal marked with
letter (L1), the live wire L2 must be connected to the terminal
marked with letter (L2) (380-420V 2N～).
10
Description of the Ceramic hob surface layout
4 zone ceramic hob schematic diagram
Table des matières
Autres manuels Bellini Plaque
