Beldray EH0089 Manuel utilisateur
Conception Wall Fire
Instruction Manual
www.beldray.com
THE SCIENCE
BEHIND CLEAN
THE SCIENCE
BEHIND HEAT
Please read all of the instructions carefully and retain for future reference.
Safety Instructions
When using electrical appliances, basic safety precautions should always
be followed.
Check that the voltage indicated on the rating plate corresponds with
that of the local network before connecting the appliance to the mains
power supply.
Children younger than 3 years old should be kept away from the
appliance unless continuously supervised.
Children aged from 3 years and less than 8 years shall only switch on/off
the appliance, provided that it has been placed or installed in its intended
operating position and they have been given supervision or instruction
concerning the use of the appliance in a safe way and understand the
hazards involved.
Children aged from 3 years and less than 8 years shall not plug in,
regulate or clean the appliance or perform user maintenance.
Children should be supervised to ensure that they do not play with
the appliance.
This appliance is not a toy.
The fixing pack contains small items, which should be kept away from
young children.
This appliance contains no user serviceable parts. If the power supply
cord, plug or any part of the appliance is malfunctioning or if it has been
dropped or damaged, only a qualified electrician should carry out repairs.
Improper repairs may place the user at risk of harm.
Keep the appliance and its power supply cord out of reach of children.
Keep the appliance and its power supply cord away from heat or sharp
edges that could cause damage.
Keep the power supply cord away from any parts of the appliance that
may become hot during use.
Keep the appliance away from other heat emitting appliances.
Keep furniture, curtains and other flammable material at least 1 metre
away from the appliance.
Do not run the supply cord under carpets, rugs etc. or anywhere where
it may present a trip hazard.
Do not immerse the appliance or plug in water or any other liquid.
Do not operate the appliance with wet hands.
EH0089 Conception Wall Fire 3
Do not use this appliance in the immediate surroundings of a bath, a
shower or swimming pool.
Do not leave the appliance unattended whilst connected to the mains
power supply or when in use.
Do not remove from the mains power supply by pulling the cord; switch
off and remove the plug by hand.
Do not use the appliance for anything other than its intended use.
Do not cover this appliance.
Do not use this appliance outdoors.
Do not attempt to move the appliance whilst it is in use.
Do not touch the appliance during use, as it will get very hot and could
cause injury.
Do not use the appliance with a programmer, timer, separate remote-
control system or any other device that will switch the appliance
on automatically, as there is a risk of fire if the heater is covered or
positioned incorrectly.
Do not clean the appliance with abrasive chemicals or materials such as
scourers as they may damage the appliance and impair future function.
The appliance should be used on a stable, heat resistant surface.
The appliance must not be located immediately below or next to a
mains power supply.
Always unplug the appliance after use and before any cleaning or maintenance.
Always ensure that the appliance has cooled fully after use, any cleaning
or maintenance.
Never use accessories that are not recommended or supplied by the
manufacturer. It could cause danger to the user and damage to the appliance.
Use of an extension cord with the appliance is not recommended.
This appliance is intended for domestic use only. It should not be used
for commercial purposes.
Note: Only use the specified rated light bulb.
Warning: In order to avoid overheating, do not cover the appliance.
Warning: This appliance is not equipped with a device to control the
room’s temperature. Do not use this appliance in small rooms whilst
occupied by persons incapable of leaving the room on their own, unless
constant supervision is provided.
EH0089 Conception Wall Fire
4
THE SCIENCE
BEHIND HEAT
Warning: Normal voltage is still present in this appliance as long as
the appliance is connected to the electrical source. Always unplug the
appliance when not in use.
Warning: In order to avoid a hazard, due to inadvertently tripping the
thermal cut-out, this appliance must not be supplied through an external
switching device, such as a timer. Nor should it be connected to a circuit
this is regularly switched on and off by the utility.
Caution: Some parts of this product can become very hot and cause
burns. Particular attention has to be given where children and vulnerable
people are present.
Caution: Hot surface. Do not touch the hot section or heating
components of the appliance.
EH0089 Conception Wall Fire 5
Getting Started
Remove the appliance from the box.
Remove any packaging from the appliance.
Place packaging inside the box and either store or dispose of safely.
In the Box
Fireplace with built-in hearth
Pebble pack
Concealed fixings pack containing:
2 metal wall brackets
1 t-shaped hook
5 wall plugs (for the wall fixing)
5 No.5 32 mm screws (for the wall fixing)
Instruction manual
Features
2000 W
Two heat settings: 1000 W/ 2000 W
Overheat protection
Thermal cut-out device
Flame effect setting
Acrylic and white pebble bowl fuel bed
Fully assembled contemporary design
EH0089 Conception Wall Fire
6
THE SCIENCE
BEHIND HEAT
Description of Parts
EH0089 Conception Wall Fire 7
1. Main body
2. Heating 1 switch
3. Heating 2 switch
4. Fan switch
5. On/Off switch
6. Hearth
7. Pebbles
8. Control panel
9. Translucent cover (underneath pebbles)
10. Fire bowl
1
10
8
5 4 2 3
6
7
9
Instructions for Use
Before First Use
When using this Conception Wall Fire for the first time, a slight odour may be emitted. This is
normal and will subside after a few uses.
Place the Conception Wall Fire on a flat, stable, heat-resistant surface at least 1 metre away from
furniture, curtains or any other flammable materials.
If placing the Conception Wall Fire in an alcove, make sure that there is at least 150 mm of space
on all sides, to ensure good air circulation.
The Conception Wall Fire must not be located over a mains power socket. The mains power
socket must always be accessible in order to disconnect the Conception Wall Fire from the
mains power supply for cleaning, maintenance or when replacing a bulb.
Wall Mounting the Conception Wall Fire
Installation of the Conception Wall Fire should be carried out by two people in order to avoid
injury, damage to the property or the fireplace.
STEP 1: Ensure that the Conception Wall Fire is unplugged from the mains power supply.
STEP 2: Open the fixing pack and place all of the contents into a container. This will reduce the
risk of losing any small pieces.
STEP 3: At the rear of the Conception Wall Fire at each side, there is a bracket (shown below).
These fire brackets engage behind the wall mounted brackets to provide a secure fixing method
that cannot be seen in normal use.
Hold the fireplace to the wall that it will be fixed to and using a pencil, mark the height of the
brackets at each side of the fire.
STEP 4: The wall bracket needs to be mounted approximately 30 mm inwards from the outer
edge of the fire surround to match the position of the fire brackets. Hold the wall brackets in
place and carefully mark the positions of the screw holes onto the wall.
EH0089 Conception Wall Fire
8
30 mm
THE SCIENCE
BEHIND HEAT
STEP 5: Drill where the holes have been marked, then insert the wall plugs.
STEP 6: Screw the wall brackets into place.
STEP 7: Hold the Conception Wall Fire above the brackets, leaning it against the wall
for support.
STEP 8: Carefully lower the Conception Wall Fire onto the brackets.
Note: You will notice a slight gap behind the fireplace, this is normal as it is required for air ventilation.
Note: Do not cut the wire to fix the wiring to a wall socket, as this will invalidate your guarantee.
Mounting the Conception Wall Fire on a Separate Hearth
In order to avoid the possibility of the fire being accidentally lifted from its side mounting brackets
when the fire is mounted on a separate hearth, an additional bracket is provided.
STEP 1: Ensure that the Conception Wall Fire is unplugged from the mains power supply.
STEP 2: Open the fixing pack and place all of the contents into a container. This will reduce the
risk of losing any small pieces.
STEP 3: At the rear of the Conception Wall Fire at each side, there is a bracket (shown below).
These brackets engage behind the wall mounted brackets to provide a secure fixing method that
cannot be seen in normal use.
EH0089 Conception Wall Fire 9
30 mm
STEP 4: The wall bracket needs to be mounted approximately 30 mm inwards from the outer
edge of the fire surround. Hold the wall brackets in this position and carefully mark the
positions of the screw holes.
STEP 5: Drill where the holes have been marked, then insert the wall plugs.
STEP 6: Screw the wall brackets into place.
STEP 7: Hold the Conception Wall Fire above the brackets, leaning it against the wall for support.
STEP 8: Carefully lower the Conception Wall Fire onto the brackets so that the fireplace rests
on the hearth.
STEP 9: Using a pencil, draw a line approximately 100 mm along the wall against the edge of
the hearth, starting from the outer right hand side of the Conception Wall Fire. Repeat
this at the left side of the fire. This will mark the height of the hearth against the wall as
well as where the corners of the Conception Wall Fire will sit.
STEP 10: Remove the Conception Wall Fire by lifting it from the wall mounting brackets and
then remove the hearth.
STEP 11: Using the lines drawn onto the wall as a reference, drill a hole in the centre, 20 mm
below the base of the Conception Wall Fire.
STEP 12: Insert the wall plug into the hole.
STEP 13: On the Conception Wall Fire, insert the t-shaped bracket into the recess in the
bottom centre of the front panel. They should hang below the Conception Wall Fire.
STEP 13: Refit the Conception Wall Fire onto the wall brackets, ensuring that it does not drop
below the baseline previously marked.
STEP 14: Screw the t-shaped bracket to the wall.
STEP 15: Slide the hearth back into place underneath the Conception Wall Fire.
Note: It may be necessary to lift the fire slightly whist fitting the t-shaped bracket.
EH0089 Conception Wall Fire
10
30 mm
THE SCIENCE
BEHIND HEAT
Installing the Pebbles
Remove the pebbles from the packaging.
Arrange them evenly on the translucent cover over the fire bowl.
If the pebbles do not let through an even amount of light once the Conception Wall Fire has
been turned on, turn off the Conception Wall Fire at the mains power supply, allow to cool
completely and then rearrange the pebbles on the translucent surface until the desired effect has
been reached.
Using the Conception Wall Fire
STEP 1: Plug the Conception Wall Fire into the mains power supply.
STEP 2: Turn on the Conception Wall Fire by pressing the ‘On/Off’ switch. This will also
operate the light.
STEP 3: To operate the Conception Wall Fire, first turn on the ‘Fan’ switch.
STEP 4: Select the desired heat output by turning on one or both of the heat setting switches.
To operate the Conception Wall Fire at a low heat setting (1000 W), turn on the
‘Heating 1’ switch. To operate the Conception Wall Fire at a high heat setting, turn on
switches marked ‘Heating 1’ and ‘Heating 2’ together (2000 W).
Note: The Conception Wall Fire will only operate if the ‘Fan’ switch is turned on.
Note: Turning on the ‘Fan’ switch without turning on either of the ‘Heating’ switches will
operate the Conception Wall Fire without heat.
Note: Selecting the ‘Heating 2’ switch will have no effect on the Conception Wall Fire.
EH0089 Conception Wall Fire 11
mark these lines
drill hole here
centre line
Table des matières
