Beko BX B7S / BLED Manuel utilisateur
CONFIDENTIAL BX B7S / BLED
Heat Pump Tumble Dryer
24
September’ 17
Sensitivity: Public
Step 11: “Start/Pause” button is pressed. “Anti-Creasing Led” lights on. Motor start to rotate
in counter-clockwise direction. “Sound Warning Led” starts to blink and it is allowed to pass
to the next step.
Step 12: “Start/Pause” button is pressed. The service test program will be exited.
7. Service Test Program BLED:
Step 1: Press “Dryness Level(1)” and “Start/Pause(2)” button, then turn the “On/Off
Program Selection Knob(3)” 90 degrees in clockwise direction within 2 seconds.
These combination will start service test program. In this program “Start/Pause”
button is used to pass other steps. Blinking of “Sound Warning Led” means that the
step is OK and it is allowed to pass to the next step.(SHP : Service Test – Heat
Pump Type)
Step 2: “Start/Pause” button is pressed. All leds blink and service test program waits
another “Start/Pause”press.
1
2
3
CONFIDENTIAL
Beko2013
Good+
Heat Pump Tumble Dryer
25
September’ 17
Sensitivity: Public
Step 3: “Start/Pause” button is pressed. Version of main software is shown on
display and service test program waits another “Start/Pause”press.
Step 4: “Start/Pause” button is pressed. Revision of main software is shown on
display and service test program waits another “Start/Pause”press.
Step 5: “Start/Pause” button is pressed. Revision of parametric software and its
number are sequentially shown on display and service test program waits another
“Start/Pause”press.
Step 6: “Start/Pause” button is pressed. All leds light on and service test program
waits another “Start/Pause”press.
Step 7: “Start/Pause” button is pressed. The last error codes are shown on display.
In this section, this error codes could be deleted by service technician with “On/Off
Program Selection Knob”. Knob have to get position 180 degree according to inital
position as shown in the picture.
CONFIDENTIAL BX B7S / BLED
Heat Pump Tumble Dryer
26
September’ 17
Sensitivity: Public
Step 8: “Start/Pause” button is pressed. The door and compressor NTC are checked
in this step. If there is no short or open circuit sensation error, door NTC value and
compressor NTC value are sequentially shown on display and it is allowed to pass to
next step.
Door NTC Open Circuit : “d:OC” is shown on display
Door NTC Short Circuit : “d:SC” is shown on display
Compressor NTC Open Circuit : “h:OC” is shown on display
Compressor NTC Short Circuit : “h:SC” is shown on display
If NTC and voltage error occurs, it is not allowed to pass to the next step.
Step 9: “Start/Pause” button is pressed. “F On” appears on display. The compressor
cooling fan starts to work. “Sound Warning Led” starts to blink and it is allowed to
pass to the next step.
Step 10: “Start/Pause” button is pressed. “Pon” appears on display. The pump
activates. If the socket of the overflow micro switch is not connected, “Tank Full Led”
blinks. If it is connected, “Sound Warning Led” blinks and it is allowed to pass to the
next step.
Important Note: If “Tank Full Led” blinks, the overflow micro switch and cables have
to be checked.
Step 11: “Start/Pause” button is pressed. “Drr” appears on display. Motor rotates in
clockwise direction. After 3 seconds, “Sound Warning Led” starts to blink and it is
allowed to pass to the next step.
CONFIDENTIAL
Beko2013
Good+
Heat Pump Tumble Dryer
27
September’ 17
Sensitivity: Public
Step 12: “Start/Pause” button is pressed. Motor continues to rotate in clockwise
direction. “Clean Filter Led” starts to blink for humidity sensor short circuit control.
Open the door of tumble dryer and make the sensor short circuit by touching the
sensor plate. If short circuit control of humidity sensor is OK, “Clean Filter Led” stops
to blink, “Sound Warning Led” starts to blinks, “Sco” appears on display and it is
allowed to pass to the next step.
Important Note: At the step 10, the sensor plate needs to be short circuit in 10
seconds, otherwise short circuit error occurs. If error occurs “ScE” appears on
display. In this situation below steps must be followed:
1. Dryer must be switched off and service test have to be restarted.
2. If the same error is seen in second trial, a problem may be in humidity
sensor cables and sockets. Please check humidity sensor cables and
sockets.
3. A problem may be in humidity sensor.
4. If there is not a problem in above parts, a problem may be in main
board.
Step 13: “Start/Pause” button is pressed. All components stop. “StP” appears on
display. After 3 seconds, “Sound Warning Led” starts to blink and it is allowed to pass
to the next step.
Step 14: “Start/Pause” button is pressed. “Drr” appears on display. Motor starts to
rotate in clockwise direction. If humidity sensor is open circuit, “Sound Warning Led”
starts to blink and it is allowed to pass to the next step. If the sensor is not open
circuit, “Clean Filter Led” starts to blink and it cannot be passed to the next step till
the sensor is open circuit.
CONFIDENTIAL BX B7S / BLED
Heat Pump Tumble Dryer
28
September’ 17
Sensitivity: Public
Step 15: “Start/Pause” button is pressed. “Crn” appears on display. Compressor
starts to work. After that, compressor NTC value appears on display and the value
starts to increase. If the compressor NTC value reaches the 50-55 °C, “C on”
appears on display, “Sound Warning Led” starts to blink and it is allowed to pass to
the next step.
Step 16: “Start/Pause” button is pressed, “rLL” appears on display. Motor starts to
rotate in counter - clockwise direction. “Sound Warning Led” starts to blink and it is
allowed to pass to the next step.
Step 17: “Start/Pause” button is pressed. The last error codes are shown on display.
In this step, error codes cannot be deleted. It is allowed to finish the service test
program.
Step 18: “Start/Pause” button is pressed. The service test program will be exited.
CONFIDENTIAL
Beko2013
Good+
Heat Pump Tumble Dryer
29
September’ 17
Sensitivity: Public
Error Codes:
Error Codes Definition
E 00 : No error
E 01 : Door Opened While Running
E 02 : Tank Full
E 03 : Drum Empty
E 04 : Start While Door Open
E 05 : Maximum Time
E 06 : Door NTC: Open Circuit
E 07 : Door NTC: Short Circuit
E 08 : Door NTC: Overheat
E 09 : Compressor NTC: Open Circuit
E 10 : Compressor NTC: Short Circuit
E 11 : Compressor NTC: Overheat
E 12 : Belt Broken
E 13 : Filter Blocked
E 14 :
E 15 :
E 16 : Low Voltage (Lower than 165V)
E 17 : High Voltage (Higher than 265V)
E 18 : BLDC Communication Error (for tumble dryer with BLDC motor)
E 19 : BLDC System Pause (for tumble dryer with BLDC motor)
E 20 : BLDC RPM Tolerance (for tumble dryer with BLDC motor)
E 21 : BLDC Minimum RPM (for tumble dryer with BLDC motor)
E 22 : BLDC Reenergized (for tumble dryer with BLDC motor)
E 23 : BLDC Abnormal Voltage (for tumble dryer with BLDC motor)
E 24 : BLDC Overheat (for tumble dryer with BLDC motor)
E 25 : BLDC Locked Rotor (for tumble dryer with BLDC motor)
E 26 : BLDC Overspeed (for tumble dryer with BLDC motor)
E 27 : BLDC Overcurrent (for tumble dryer with BLDC motor)
E 31 : Combined Filter Not Mounted (for combined filter models)
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Beko Séchoir
Beko
Beko DHX 83420W Manuel utilisateur
Beko
Beko DRX927WN Manuel utilisateur
Beko
Beko B3T68230 Manuel utilisateur
Beko
Beko DS 8133 G Manuel utilisateur
Beko
Beko B5T68243WBDC Manuel utilisateur
Beko
Beko DPY 8507 GXB1 Manuel utilisateur
Beko
Beko DRYPOINT RA 1080-8800 Guide de l'utilisateur
Beko
Beko DS 7434 RX Manuel utilisateur
Beko
Beko DHS 8412 PA0 Manuel utilisateur
Beko
Beko DPY 8505 GXB2 Manuel utilisateur
Beko
Beko DPY 8506 GXB1 Manuel utilisateur
Beko
Beko B5T68247 Manuel utilisateur
Beko
Beko DF7439SXUV Manuel utilisateur
Beko
Beko DIH7452TA Manuel utilisateur
Beko
Beko DU7112GAW Manuel utilisateur
Beko
Beko DS9414CX2 Manuel utilisateur
Beko
Beko DC 7110 Manuel utilisateur
Beko
Beko DRYPOINT M intelligence Manuel utilisateur
Beko
Beko DCU 7230 X Manuel utilisateur
Beko
Beko DCUR 701 W Manuel utilisateur
Manuels Séchoir populaires d'autres marques
Infiniton
Infiniton SD-DG85C Manuel utilisateur
BOMANN
BOMANN WT 5019 Manuel utilisateur
Alliance Laundry Systems
Alliance Laundry Systems TMB795C Manuel utilisateur
Asko
Asko T793C Manuel utilisateur
Kenmore
Kenmore 8041 - 5.8 cu. Ft. Capacity Electric Dryer Manuel utilisateur
Frigidaire
Frigidaire CAQE7077KW0 Manuel du propriétaire