Behringer MonoPoly Manuel utilisateur

page 1 of 6

985-40000-01200 Rev.A

2022-04-21

Condential, for internal use only. Not to be reproduced.

Analog 4-Voice Polyphonic Synthesizer with

37 Full-Size Keys, 4 VCOs, VCF,

2 LFOs, 2 Envelopes, Sync and Cross

Modulation and Arpeggiator

Synthesizers and Samplers

MONOPOLY

Service Support Bulletin

History

Requirement

This calibration function is only available on 1.0.5 or later version rmware.

Date Version Note

2021-03-03 Rev0 Initial version

How to start calibration

Power o MONOPOLY rst.

Long press and hold button HOLD and POLY simultaneously.

page 2 of 6

985-40000-01200 Rev.A

2022-04-21

Condential, for internal use only. Not to be reproduced.

page 2 of 6

Synthesizers and Samplers

MONOPOLY

Cycle power on MONOPOLY.

Wait approximately 2 seconds until power LED blinking slowly.

Release all buttons.

There are 3 sub calibration menus. Press the corresponding button to enter the sub menu.

Tip:

You can only calibrate one channel at a time. Ignore the other channels if you don't want to change them.

Sub Calibration Menu

(Channel) Buttons Function Button LEDs VCO LEDs

1MONO UNISON PITCH WHEEL MAX/MIN indicates PITCH WHEEL position VCO1 LED on

2POLY UNISON PITCH WHEEL dead zone indicates PITCH WHEEL dead zone VCO2 LED on

3POLYPOLY MOD WHEEL MAX/MIN indicates MOD WHEEL position VCO3 LED on

page 3 of 6

985-40000-01200 Rev.A

2022-04-21

Condential, for internal use only. Not to be reproduced.

page 3 of 6

Synthesizers and Samplers

MONOPOLY

Calibration Procedure

Follow all steps in the order they are presented.

Start BEND WHEEL Calibration

Press button MONO UNISON, then VCO1 LED will illuminate.

Calibrate BEND WHEEL maximum position

Move the BEND WHEEL to its maximum position.

page 4 of 6

985-40000-01200 Rev.A

2022-04-21

Condential, for internal use only. Not to be reproduced.

page 4 of 6

Synthesizers and Samplers

MONOPOLY

Calibrate BEND WHEEL minimum position

Move the BEND WHEEL to its minimum position.

Start BEND WHEEL dead zone calibration

This step is to ensure that no bend information is sent while bend wheel is not being touched.

1. Make sure the BEND WHEEL is released and returned to its center position before further operation.

2. Press button POLY UNISON, then VCO2 LED will light up.

page 5 of 6

985-40000-01200 Rev.A

2022-04-21

Condential, for internal use only. Not to be reproduced.

page 5 of 6

Synthesizers and Samplers

MONOPOLY

Start MG1 WHEEL Calibration

Press button POLY POLY, then VCO3 LED will illuminate.

Calibrate MG1 WHEEL maximum position

Move the MG1 WHEEL to its maximum position.

Calibrate BEND WHEEL dead zone

Move the BEND WHEEL within the dead zone where you don't feel the tension of the spring.

page 6 of 6

985-40000-01200 Rev.A

2022-04-21

Condential, for internal use only. Not to be reproduced.

page 6 of 6

Condential, for internal use only. Not to be reproduced.

Music Tribe accepts no liability for any loss which may be suered by any person who relies either wholly or in part upon any description, photograph, or statement contained herein.

Technical specications, appearances and other information are subject to change without notice. All trademarks are the property of their respective owners. Midas, Klark Teknik,

Lab Gruppen, Lake, Tannoy, Turbosound, TC Electronic, TC Helicon, Behringer, Bugera, Aston Microphones and Coolaudio are trademarks or registered trademarks of

Synthesizers and Samplers

MONOPOLY

End of Procedure

Complete calibration

Short press HOLD + EFFECTS will conrm and save all calibration result. If successful, all BUTTON LEDs will blink at the

same time for a while. Otherwise, it may be a failed calibration.

NOTE: Press HOLD + MONO CHORD will cancel all calibration and return back to normal mode.

Calibrate MG1 WHEEL minimum position

Move the MG1 WHEEL to its minimum position.

Autres manuels pour MonoPoly

Table des matières

Autres manuels Behringer Synthétiseur

Behringer

Behringer SYSTEM 55 Manuel utilisateur

Behringer

Behringer CRAVE Manuel utilisateur

Behringer

Behringer POLY D Manuel utilisateur

Behringer

Behringer TD-3 Manuel utilisateur

Behringer

Behringer CRAVE Manuel utilisateur

Behringer

Behringer NEUTRON Manuel utilisateur

Behringer

Behringer 2600 Manuel utilisateur

Behringer

Behringer DeepMind 6 Manuel utilisateur

Behringer

Behringer PRO-VS MINI Manuel utilisateur

Behringer

Behringer FILTAMP MODULE 1006 Manuel utilisateur

Behringer

Behringer 962 SEQUENTIAL SWITCH Manuel utilisateur

Behringer

Behringer CRAVE Instructions d'installation

Behringer

Behringer 110 VCO/VCF/VCA Manuel utilisateur

Behringer

Behringer MODEL D Manuel utilisateur

Behringer

Behringer K-2 Manuel utilisateur

Behringer

Behringer SYSTEM 55 Manuel utilisateur

Behringer

Behringer PRO-1 Manuel utilisateur

Behringer

Behringer 914 Fixed Filter Bank Manuel utilisateur

Behringer

Behringer WASP DELUXE Manuel utilisateur

Behringer

Behringer POLY D Instructions d'installation

Behringer

Behringer ODYSSEY Manuel utilisateur

Behringer

Behringer DEEPMIND 12 Manuel utilisateur

Behringer

Behringer NEUTRON Instructions d'utilisation et d'entretien

Behringer

Behringer SYSTEM 100 172 PHASE SHIFTER/DELAY/LFO Manuel utilisateur

Manuels Synthétiseur populaires d'autres marques

Kawai

Kawai MP7 Manuel technique

Joranalogue

Joranalogue Contour 1 Manuel utilisateur

Full Bucket Music

Full Bucket Music Mono/Fury Manuel utilisateur

Kawai

Kawai PH50 Manuel utilisateur

IK Multimedia

IK Multimedia UNO Synth PRO X Manuel utilisateur

Roland

Roland Gaia SH-01 Manuel utilisateur

Roland

Roland GR-30 Manuel utilisateur

Gotharman

Gotharman Gotharman's anAmoNo-box Manuel utilisateur

Yamaha

Yamaha DX21 Manuel utilisateur

QuStream

QuStream HDFS-550 Manuel utilisateur

Modal Electronics

Modal Electronics ARGON8 Manuel utilisateur

Roland

Roland GS-500 Manuel utilisateur

Octave

Octave Cat SRM Manuel utilisateur

Dreadbox

Dreadbox Murmux Initiate Manuel utilisateur

neutral labs

neutral labs ELMYRA 2 Manuel utilisateur

Waldorf

Waldorf KYRA Manuel utilisateur

Tubbutec

Tubbutec Juno-66 Manuel utilisateur

EFM

EFM VCADSR - 3510 Manuel utilisateur