Beck Com.tom GRAPHIC 4.11 Manuel utilisateur

com.tom GRAPHIC 4.11

Getting Started V1.1

com.tom GRAPHIC 4.11

Getting Started

com.tom GRAPHIC 4.11

Getting Started V1.1

TABLE OF CONTENTS

1INTRODUCTION.................................................................................................. 3

2SCOPE................................................................................................................. 3

3SYSTEM START-UP............................................................................................ 3

3.1WHAT DO WE NEED TO GET STARTED? .................................................................................. 3

3.2STEP 1–CABLE AND THE COM.TOM GRAPHIC..................................................................... 4

3.3STEP 2–CONFIGURE THE NETWORK SETTINGS OF THE COM.TOM GRAPHIC ........................ 5

3.4STEP 3–CONFIGURE THE MICROBROWSER SETTINGS OF THE COM.TOM GRAPHIC.............. 6

3.5STEP 4–ADVANCED SETTINGS OF THE COM.TOM GRAPHIC ................................................ 7

3.5.1Advanced Settings / Page 1 .............................................................................................. 7

3.5.2Advanced Settings / Page 2 .............................................................................................. 8

3.5.3Advanced Settings / Page 3 .............................................................................................. 9

3.6STEP 5–FILE SYSTEM SETTINGS OF THE COM.TOM GRAPHIC........................................... 10

3.7STEP 6–INFO OF COM.TOM GRAPHIC .............................................................................. 10

3.7.1Info / Page 1..................................................................................................................... 10

3.7.2Info / Page 2 – Firmware Update..................................................................................... 11

3.8LOAD DEFAULT SETTINGS OF COM.TOM GRAPHIC.............................................................. 13

4WHERE TO GET FURTHER INFORMATION.................................................... 14

4.1GETTING STARTED............................................................................................................. 14

4.2UPDATES,TOOLS,DOCUMENTATION.................................................................................... 14

4.3SUPPORT........................................................................................................................... 14

com.tom GRAPHIC 4.11

Getting Started V1.1

1 Introduction

This document will help you get started with com.tom GRAPHIC and SpiderControlTM

MicroBrowser. The SpiderControlTM MicroBrowser is able to run Web-HMI’s that are directly

loaded from an embedded Web-server on a PLC or another controller device.

2 Scope

Currently the com.tom GRAPHIC software is known to run with the following devices:

CoDeSys v 2.x

CoDeSys v 3.x

SpiderControl Wago

SpiderControl Siemens S7-200/300 (mit integriertem Webserver)

SpiderControl Panasonic

SpiderControl Beckhoff SpiderControlTM editor, or compatible OEM versions

3 System start-up

3.1 What do we need to get started?

The following components are among others included within the com.tom Starter Kits:

com.tom GRAPHIC 4.11

com.tom GRAPHIC ETH-01 (or a equivalent com.tom GRAPHIC ETH-0x)

Power supply unit

Ethernet cable

Furthermore you need:

A running WEB Server on a PLC or another controller device (as mentioned above)

com.tom GRAPHIC 4.11

Getting Started V1.1

3.2 Step 1 – Cable and the com.tom GRAPHIC

Insert the com.tom GRAPHIC ETH-01 adaptor and look it with the screw.

Use an Ethernet cable to connect the com.tom GRAPHIC to your embedded Web-server or

the PLC. If you have an existing network infrastructure, use a patch cable to connect the

com.tom GRAPHIC to your hub or switch. If not, use a crossover cable to directly connect the

com.tom’s GRAPHIC Ethernet jack to your embedded Web-server or the PLC Ethernet jack.

Now connect the power supply unit to the com.tom GRAPHIC/ETH01 power supply jack to

power the device.

Right after the device is powered on a view appears to calibrate the touch-screen. Press the

screen to start the touch-screen calibration routine.

After the touch-screen calibration is finished the view “Starting Ethernet, please wait” appears.

Shortly after the next view appears:

Press on `☼Settings` to access the configuration menu of the com.tom GRAPHIC.

com.tom GRAPHIC 4.11

Getting Started V1.1

If no action is taken, the panel will automatically continue by loading the URL that has been

previously configured. If this URL cannot be found, this page will be shown again and the

system will try to reconnect again.

Now you are in the “Setting” Menu and can go ahead with the next step.

3.3 Step 2 – Configure the Network Settings of the com.tom GRAPHIC

Press on 'Network Settings', the Page to enter the network configuration of the com.tom

GRAPHIC. DHCP for IP and DNS server is activated by default settings.

Alternative you can configure a static IP address, DHCP, subnet mask and gateway.

Therefore press the DHCP button, the change is displayed by the button.

In that case you have to touch in the `field` IP address and enter your static IP with the

appearing Key-Pad. In the same way you have to configure the Subnet mask and the

Gateway.

'DNS via DHCP' is activated by default settings.

Alternative you can configure the DNS server, if there a server is in your network.

Therefore press the DHCP/DNS server button , the change is displayed

by the button.

In that case you have to touch in the `field` DNS server and enter your static IP with the

appearing Key-Pad.

com.tom GRAPHIC 4.11

Getting Started V1.1

Press the Button to go back to the “Setting” Menu.

3.4 Step 3 – Configure the MicroBrowser Settings of the com.tom GRAPHIC

Press the ´MicroBrowser Settings´ to access the configuration menu.

The entry `Host` is for the IP-Address of the host with the located HMI. By default settings the

preset is `192.168.0.3`.

Touch in the `field` with the IP-Address `192.168.0.3` and enter the IP-Address of the WEB-

Server of your PLC (as mentioned in Chapter 2) with the appearing Num-Pad.

Now check the reachability of your configured PLC by pressing the button.

Then answer on the ping request fade the button green

If you have no success of the ping test, the button fades to red , check your network.

The 'Start Page' field contain the HTML-file name of the HMI. In the default setting the entry is

blank. Touch in the blank `field` and enter the HTML-file name of the HMI with the appearing

Key-Pad e.g. “webvisu.html”.

If the host provide the startpage in a subfolder include the path information. Use ' /' as

separator (Examples: “plc/webvisu.html”)

The Start URL is read-only, the composed URL is shown (e.g.:http://192.168.0.3/webvisu.html)

By changing the default disabled Pre-load option to enable , by pressing the button,

all views and image files are pre-loaded. This will increase the loading time, but reduce the

time between page jumps.

Press the Button to go back to the “Setting” Menu.

com.tom GRAPHIC 4.11

Getting Started V1.1

3.5 Step 4 – Advanced Settings of the com.tom GRAPHIC

The advanced settings are represented on three pages. The default settings are set to use the

com GRAPHIC without changes.

Press the ´Advanced Settings´ to access the configuration menu.

3.5.1 Advanced Settings / Page 1

With the `Brightness fader` change the screen brightness to your needs. Press the fader and

move it to your favoured attitude. Please consider with a Brightness of 0% the Display could

be complete dark.

This value is not used when the “Auto mode” is set.

The ´Auto mode´ is disabled by default.

In the `Auto mode` the screen brightness is set automatically according to the ambient

brightness. To change into `Auto mode` you have at first to set with “day” and “night” ambient

brightness value. The measured Brightness is read-only displayed with “Ambient”.

Make sure that your ambient is ´day´ (consider that an average value is used – it takes a

minute after changing the ambient) and press the button .

By default the “day Brightness” is 100%, to change this touch in the `% field` below “set day”

and set it with the appearing Key-Pad to another value, e.g. “90%”.

Now set your ambient to night – for test we simulate it with a piece of normal white paper we

place over the sensor.

After a minute the Ambient value is reduced clearly and we press the button

Change Brightness value by touch in the `% field` below “set night” and set it with the

appearing Key-Pad to “20%” (please consider with a Brightness of 0% the display could be

complete dark).

Now switch the “Auto mode” on, by pressing the button. The display will reduce the Brightness

after a short time.

com.tom GRAPHIC 4.11

Getting Started V1.1

After removing the small piece of paper from the sensor the display becomes brighter after a

short time.

Proximity wake up is not supported right now, leave it “disabled”.

Press the Button for the Advanced Settings / Page 2.

3.5.2 Advanced Settings / Page 2

The ´Turn off backlight´ entry sets a time constant, after which the backlight is automatically

switched off if the display is not in use (no touch events are registered).

This setting is set in minutes. 'N' means never / disabled. By factory default its set to “N”.

We change it to 1minute by pressing on the button

Now we wait 1 minute without touching the display/touch and the Backlight switches off, the

display is “dark”. By touching the display/touch the Backlight switch on.

The `Automatic scaling` entry offers setups for scaling/ omit. The best result is given with the

default `disabled`. The HMI is drawn 1:1 (scale factor 1) on the com.tom GRAPHIC. Elements

positioned outside the screen resolution are omitted.

If necessary you can change the settihg by pressing the according button.

'enabled, keep ratio' scales the HMI to the screen resolution. The view will be stretched or

shrunk and the ratio is kept.

'enabled, don't keep ratio' scales the HMI to the screen resolution. The view will be stretched

or shrunk and the ratio is not kept.

`Display orientation`

With the four buttons `Display orientation` you can rotate the presentation. For a short test

we rotate it from the default of 180° to 0° orientation by pressing the button

For the 90° and 270° “Portrait Mode” you should consider that the HMI Design should

prepared for.

Bei pressing the button we go back to the default orientation.

With the entry `Skip setup page` the HMI is loaded right after the initialization of the Ethernet

adapter, skipping the whole setup page.

com.tom GRAPHIC 4.11

Getting Started V1.1

If neither the HMI nor the settings gives you the possibility to return to the setup page, unplug

the Ethernet cable and restart the device. We not change this setting.now.

Press the Button for the Advanced Settings / Page 3.

3.5.3 Advanced Settings / Page 3

The stetting `Check for project update` defines the check, whether a HMI has been updated.

In this case the HMI is re-loaded automatically. This sets the interval between the checks. The

time must be at least as long as the time needed to upload the whole project.

It’s no need to change it for this getting started. Remember this option in case you change

your HMI on your PLC. You change the update time by pressing one of the buttons.

With enabling `return to setup page` touching the screen for the given value, by pressing the

“5” or “10” button the com.tom GRAPHIC jumps back to the setup menu.

This setting is set in seconds. 'N' means never / disabled.

It’s no need to change it for this getting started.

The button `Show performance info` is only for internal use.

By pressingthe `Touch calibration` button you can start the calibration routine of the touch-

screen.

Press the Button to go back to the “Setting” Menu.

com.tom GRAPHIC 4.11

Getting Started V1.1

3.6 Step 5 – File System Settings of the com.tom GRAPHIC

Press on `File System`, the Page to see the stored and available loaded Fonts. In default 30

Ariel Fonts are installed.

Press the `Back` Button.

3.7 Step 6 – Info of com.tom GRAPHIC

Press on `Info` Button to enter the page with information to the main components and

parameters.

3.7.1 Info / Page 1

A Read-only page, with information to the main components and parameters.

Read out your current Firmware and check if a new Firmware is available. Therefore refer

Chapter 4.2 Updates, tools, documentation.

If a newer Firmware is available press the Button for the Update Page, otherwise

continue with 3.8 “Load default Settings of com.tom GRAPHIC”

Autres manuels pour com.tom GRAPHIC 4.11

Table des matières

Manuels Équipement d'enregistrement populaires d'autres marques

KV2 Audio

KV2 Audio 500 Series Manuel utilisateur

Robotics Technologies

Robotics Technologies microBus-Cam II Manuel utilisateur

Seca

Seca 460 Manuel utilisateur

Cognex

Cognex MVS-8000 Series Manuel utilisateur

Mect

Mect MPNC006 Series Manuel utilisateur

Bad Caf

Bad Caf THE LEASH Manuel utilisateur

Strymon

Strymon NIGHTSKY Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Manuel utilisateur

Tews Technologies

Tews Technologies TPMC465 Manuel utilisateur

Honeywell

Honeywell Excel 50 Manuel utilisateur

SeaLevel

SeaLevel COMM+8.LPCI Manuel utilisateur

Arturia

Arturia AUDIOFUSE STUDIO Manuel utilisateur

Rukra

Rukra RK-1240 Manuel utilisateur

Samson

Samson SCOM Manuel utilisateur

Dynacord

Dynacord DPS260 Manuel utilisateur

Nice

Nice Core Manuel utilisateur

Pyle Pro

Pyle Pro PSS8 Manuel utilisateur

RF-System

RF-System TinyGate Manuel d'utilisation et d'entretien

Beck com.tom GRAPHIC 4.11 Manuel utilisateur

Manuels Équipement d'enregistrement populaires d'autres marques