BCL CP800 Manuel utilisateur

SOUND CONTROLLER CP800

Thank you for purchasing your new Brimal Sound Controller. We recommend you spend some time reading this instruction

manual in order that you fully understand all the operational features. You will also find some tips to help

issues.

Unpack the unit

The following items are included:

1 Sound Controller

2 Micro SD card

3 6 mono jack plugs 3.5 mm

4 6 Magnets 6x2mm

5 6 Reed switches

6 1 DC plug 2.5mm pin

Connection of the controller

Micro SD card.

First insert the Micro SD card into the reader. The card will only go in one way,

so make sure that the card has the notches on the left. The card will go into the

reader and click when locked in place.

To release and remove the card press the card

The Power su ly

There are two power sockets on the rear panel, both require a DC power socket with a 2.5mm pin. Please ensure that the

power supplied is between 9v & 12v DC. This can

from the main layout system.

You must ensure that the positive power is on the pin as the drawing below.

The two examples above are as follows.

Left image shows the 9 to 12v DC coming from the auxiliary power

Right image shows the power being supplied by a standalone power pack and the second power socket being used to power

other equipment.

SOUND CONTROLLER CP800

Thank you for purchasing your new Brimal Sound Controller. We recommend you spend some time reading this instruction

manual in order that you fully understand all the operational features. You will also find some tips to help

Connection of the controller

First insert the Micro SD card into the reader. The card will only go in one way,

so make sure that the card has the notches on the left. The card will go into the

To release and remove the card press the card

down and then lift out.

There are two power sockets on the rear panel, both require a DC power socket with a 2.5mm pin. Please ensure that the

power supplied is between 9v & 12v DC. This can

be either

from an additional power supply, or

You must ensure that the positive power is on the pin as the drawing below.

The two examples above are as follows.

Left image shows the 9 to 12v DC coming from the auxiliary power

output on your layout.

Right image shows the power being supplied by a standalone power pack and the second power socket being used to power

SOUND CONTROLLER CP800

Thank you for purchasing your new Brimal Sound Controller. We recommend you spend some time reading this instruction

manual in order that you fully understand all the operational features. You will also find some tips to help

you resolve any

There are two power sockets on the rear panel, both require a DC power socket with a 2.5mm pin. Please ensure that the

from an additional power supply, or

from the auxiliary output

You must ensure that the positive power is on the pin as the drawing below.

Right image shows the power being supplied by a standalone power pack and the second power socket being used to power

Initial Switch On

Once you have connected the power supply and inserted the SD card, switch the p

to ten seconds, Switch OFF. (you have rebooted the microprocessor

switch on, you can test the sounds by pulling any of the mini toggle switches down, and r

twenty to forty five seconds. All sounds can be reset by pulling the RESET switch down for a second.

External Am lifier & S eaker

The controller has a switch on the front panel to give sound to the internal speaker, or a

output is via a 3.5mm jack socket with the following polarity connection.

Please ensure the jack plug is wired as the drawing below.

Sound Trigger System

On the front panel each sound has a mini toggle s

toggle switch is left in the UP position, the sound will be triggered by the sensor connected to the corresponding input sock

on the

rear. The input circuit must be a normally open contact. There are numerous contact types, the most common will be

the reed switch which is activated by a magnet(fixed to the underside of the locomotive. These are shown in the image below

on the left side.

Once you have connected the power supply and inserted the SD card, switch the p

ower to the unit ON, and leave on for five

to ten seconds, Switch OFF. (you have rebooted the microprocessor

you will not need to do this

switch on, you can test the sounds by pulling any of the mini toggle switches down, and r

eleasing. Each sound will last from

twenty to forty five seconds. All sounds can be reset by pulling the RESET switch down for a second.

The controller has a switch on the front panel to give sound to the internal speaker, or a

n external speaker system. The

output is via a 3.5mm jack socket with the following polarity connection.

Please ensure the jack plug is wired as the drawing below.

On the front panel each sound has a mini toggle s

witch associated to it, and the

input socket on the rear panel. When the

toggle switch is left in the UP position, the sound will be triggered by the sensor connected to the corresponding input sock

rear. The input circuit must be a normally open contact. There are numerous contact types, the most common will be

the reed switch which is activated by a magnet(fixed to the underside of the locomotive. These are shown in the image below

ower to the unit ON, and leave on for five

you will not need to do this

again . The next time you

eleasing. Each sound will last from

twenty to forty five seconds. All sounds can be reset by pulling the RESET switch down for a second.

n external speaker system. The

input socket on the rear panel. When the

toggle switch is left in the UP position, the sound will be triggered by the sensor connected to the corresponding input sock

rear. The input circuit must be a normally open contact. There are numerous contact types, the most common will be

the reed switch which is activated by a magnet(fixed to the underside of the locomotive. These are shown in the image below

There is no polarity with these inputs so it is not important which way around the jack plug or the sensor switch is wired. The

important part is that the circuit is NORMALLY OPEN, otherwise the sound will be triggered continuously.

Exam le Set U

Where you position the Trigger Sensors is a personal choice and will depend a lot on the size of your layout.

The following is an example of a sequence to create the atmosphere.

CP800 DIESEL SOUND CARD

1 DMU Passing with Horn

2 Deltic Starting off

3 Diesel Starting up

4 Slow Deltic Approach

5 DMU Horn & Start up

6 Short Diesel Horn

7 Diesel Freight + Horn at Speed

8 Slow Moving Deltic

9 Coach Doors Closing

10 Station Noise Atmosphere

11 Level Crossing

12 'Next Train not Stopping'

13 Road Traffic & Pelican Crossing

14 Wagons & Couplings

15 Clickity Clack

16 RESET

This is just a small example of how the sensors can be used on a simple layout.

You can use the same sound on different tracks and different situations by wiring the sensors in parallel before they go back

to the control panel as shown below

Parallel Sensors

This drawing shows how you would use 2 (or more sensors to activate one particular sound.

Example: Using the layout above, Sensor on the left of the station is connected to sound 15 which is the Clickity Clack sound.

Depending on the size of your layout you may want this sound continuous, this means you will need to place another sensor

in the position where the Clickity Clack is about to stop. This will then reactivate the sound. The circuit below is how you do

this, you can add as many sensors to the left of this circuit as you wish.

Reset.

You can connect the RESET to a sensor if you wish. This is socket 16 on the rear. This will reset all sounds that are active at

the time.

Example: You may have a tunnel on your layout, while the train is in the tunnel you may want there to be no sounds. Fitting

a sensor at the entrance will reset all sounds to OFF as the train enters the tunnel.

The sounds last too long as the train arrives in the Station, A reset sensor can be placed where you normally stop the train.

Positioning of the Reed Switch

It is important that the reed switch and the magnets are positioned correctly, so that you have clearance as the magnet

passes over the reed switch without hitting it, but not too far above so that the magnet has no influence on the switch. The

ideal clearance is between 2 to 4mm.

Glass Reed Switches

If you are using glass reed switches, please note the following:

Glass reed switches are very fragile. If you need to bend or shorten the

wires you must first grip the wires as close to the glass (without touching

with pliers and bend or cut the wire furthest from the glass. The pliers

will prevent any strain on the glass.

Additionally, if you are soldering onto these wires, hold the wire with

pliers near the glass. The pliers will soak up the heat before it allows the

wire to expand and shatter the glass.

S ares

CP840 Steam Locomotive SD Card

CP841 Diesel Locomotive SD Card

CP 842 Underground Train SD Card

CN365 Jack Plug Mono 3.5mm with Strain Relief

CN606 DC Power Plug 5.5 Outer 2.5 Pin 10mm long

SW925 Glass Reed Switch 180vAC 0.5A

SW926 SPNO Encapsulated Reed Switch PPS150 10vA

SW927 SPNO Encapsulated Reed Switch 24v ACSW932

SW932 Neodynium Magnet 6mm x 2mm

SW933 Neodynium Magnet 3mm x 2mm

SW052 Microswitch V4 Ultra Mini Lever PCB Mtg

SW053 Sub Miniature Button Microswitch

SWP100 Leaf Switch

This unit is guaranteed for 12 months from the date of purchase. If you have any problems with the unit, please contact us on

Tel; 01429297277 or email us at [email protected]

For further information and ideas have a look at the CP800 page on thehobbyshed.co.uk

Table des matières

Manuels Matériel de musique populaires d'autres marques

DAPAudio

DAPAudio IPS-PT Manuel utilisateur

Dynacord

Dynacord DPM 8016 Manuel utilisateur

Subdecay

Subdecay Starlight Flanger Manuel utilisateur

Moen

Moen GEC8 Live Manuel utilisateur

Fender

Fender 1 Manuel utilisateur

Yamaha

Yamaha MLC-16 Manuel utilisateur

Sonuscore

Sonuscore TIME TEXTURES Manuel utilisateur

flight of harmony

flight of harmony V'Amp Manuel utilisateur

NANO

NANO PERFORMANCE MIXER Manuel utilisateur

Tascam

Tascam CD-GT2 Manuel utilisateur

BHI

BHI NEIM 1031 MKII Manuel utilisateur

Befaco

Befaco KICKALL Manuel utilisateur

Paia

Paia 9720 Mode d’emploi

limex

limex ALPIN MASTER 128 Manuel utilisateur

nord

nord Electro 3 Manuel utilisateur

Joemeek

Joemeek sixQ2 Manuel utilisateur

CARVIN

CARVIN 500W STEREO POWER MODULE - SCHEMA REV G Manuel utilisateur

Furutech

Furutech ADL GT40 Guide d'installation