BASSFACE IndyEVO10/2RK Manuel utilisateur
IndyEVO10/2RK 10" 2x2Ohm 25cm DVC
Subwoofer Recone Kit
Instruction manual
Thank you for choosing Bassface. From the simplest connector to our top of the range
amplifier - every element of these products has been designed to give you the best possible
performance for your money. Please take the time to read these instructions carefully as
they contain useful and important information. Modern high power audio systems can
generate voltages at the speaker similar to mains operated equipment – for some reason
everyone seems to ignore or forget this. Your wiring needs to be good to be safe. Please
remember this and take your time. Please exercise caution when setting volume levels –
powerful audio equipment can easily produce enough sound to permanently damage
hearing. Remember that audio competitors use ear protection when operating and
competing. Do remember that incorrect installation or abuse is not covered under warranty
– please make sure that your installation and any partnered product is suitable and
compatible. If you are unsure please seek qualified advice before proceeding. Always use
appropriate hand and eye protection when working with tools, and always work within your
capabilities as an installer. We offer a 12 month manufacturer warranty via your distributor
or retailer. Please retain your purchase receipt as proof of purchase. Please note that
Bassface operates a policy of continuous product development and we reserve the right to
change specification without prior notice. You can follow our process on our website by
reviewing the version history information.
Please note that we sometimes include information inside these manuals which we feel is of
potential value to the client on related subjects such as conversion charts, capacitance
values or wiring diagrams. Please feel free to copy any of this information since it is in the
public domain.
Begin by removing the old cone and coil from the woofer. Use a sharp knife, carefully
cutting the surround, spider and tinsels. You can also use a heat gun (carefully!) to warm
the parts to around 110 degrees. This will soften the adhesive sufficiently to strip the
speaker without cutting. Either way, once the old parts are removed, clean any
contamination of the surfaces - old glue or residue - and prepare to fit the new cone and
motor. Use a Cyanoacrylate rubberised adhesive. If you can't find that we have great
success with "Tiger Seal" or "Wurth Zebra" rubber adhesive. Do not use normal super glue!
Use the provided coil alignment tool to ensure the new coil is centred in the voice coil gap
and apply a 3mm bead of adhesive around the spider and surround areas. Ensure the bolts
are evenly torqued to 7Nm. Make sure the glue is well and evenly pressed into the surround
and use the gasket or other circular piece with clothes pegs to hold the assembly together
during setting. Once the glue is fully set, ensure to remove the coil shim tool and check for
smooth movement of the woofer. Pay attention to installing the tinsel leads at this point. To
fit the dustcap we recommend to use strips of masking tape in closely arranged straight
lines to form a circular mask - this will prevent excess glue from contaminating the new
cone. Apply an even bead of adhesive and make sure the dust cap is pressed on centrally
and firmly.
Once the speaker is installed and working it is vitally important to follow a break in
procedure. For most of our woofers before 2020 with single spiders a short break in period
of a few hours at medium volume, making sure the woofer is not in any way stressed, will
result in a satisfactory loosening of the components. For our newer woofers since 2020 with
a specialist multi spider suspension setup such as IndyS series it is absolutely critical that
the speakers are not extended until at least 20 hours of playing at medium level Free air
has been completed. Failure to do this will almost certainly lead to failure of the motor/coil
due to the suspension presenting excessive resistance in its pre-break in state. Failure of
speakers due to insufficient running in is not covered by warranty. Please note that TS
parameters can and do change dramatically after break in - until the speaker is at its
equilibrium.
Table des matières
Autres manuels BASSFACE Subwoofer
BASSFACE
BASSFACE BIGRED15.5 Manuel utilisateur
BASSFACE
BASSFACE SPL15.3 Manuel utilisateur
BASSFACE
BASSFACE IndyEVO8/2RK Manuel utilisateur
BASSFACE
BASSFACE IndyEVO10/2 Manuel utilisateur
BASSFACE
BASSFACE SDC.3 Manuel utilisateur
BASSFACE
BASSFACE IndyS8/2RK Manuel utilisateur
BASSFACE
BASSFACE SPL10.2 Manuel utilisateur
BASSFACE
BASSFACE IndyS8/2 Manuel utilisateur
BASSFACE
BASSFACE XPL15.1 Manuel utilisateur
BASSFACE
BASSFACE GT Audio GT-SW8/4 Manuel utilisateur
BASSFACE
BASSFACE SPLI5.1 Manuel utilisateur
BASSFACE
BASSFACE Indy EVO15/2 Manuel utilisateur
BASSFACE
BASSFACE SPL12.3 Manuel utilisateur
BASSFACE
BASSFACE GT Audio GT-SW12/4 Manuel utilisateur
BASSFACE
BASSFACE IndyS10/2 Manuel utilisateur
BASSFACE
BASSFACE IndyS12/2 Manuel utilisateur
BASSFACE
BASSFACE Team RED12/2 Manuel utilisateur
BASSFACE
BASSFACE Team RED15/2 Manuel utilisateur
BASSFACE
BASSFACE IndyEVO8/2 Manuel utilisateur
BASSFACE
BASSFACE SPL15.2 Manuel utilisateur
