BARRON Exitronix SCL Series Manuel utilisateur

IMPORTANT SAFEGUARDS

READ AND FOLLOW ALL SAFETY INSTRUCTIONS.

When using electrical equipment, basic safety precautions should always be followed including the following:

• DISCONNECT AC POWER SUPPLY BEFORE SERVICING.

• Installation and servicing of this equipment should be performed by qualified service personnel only.

• Ensure that the electrical wiring conforms to the National Electrical Code NEC® and local regulations

if applicable.

• Do not mount near gas or electrical heaters.

• Do not use outdoors.

• Equipment should be mounted in locations and at heights where it will not be readily subjected to tampering

by unauthorized personnel.

• The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition.

• Any modification or use of non-original components will void the warranty and product liability.

• Do not use this equipment for other than intended use.

• Allow battery to charge for 24 hours before first use.

SAVE THESE INSTRUCTIONS!

SCL Series

Installation Instructions

10070159 REV 5 - 09/19 1 800-533-3948 www.barronltg.com

Technical Support ■ (623) 580-8943 ■ [email protected]

SCL Series

Installation Instructions

10070159 REV 5 - 09/19 2 800-533-3948 www.barronltg.com

1. Remove (A) 6-32 X 1/4” screws securing cover and set aside (Fig. 1-1 )

2. Slide front cover (B) forward and flip down. (Fig.1-2a, b)

(A)

Fig. 1-1 Fig. 1-2a

(B)

Fig. 1-2b

3. Stem mount option (Fig. 2-0a, b and 2-1a,b)

a. Thread 2 nuts (D) approximately 1/2” onto threaded rod (G). Add 1 lock washer (C). Insert threaded rod (G) into top

of enclosure as shown in Fig. 2-0.

b. Using nuts (D) to hold threaded rod (G) in place thread lock nut (F) in place.

Note: Must thread lock nut (F) in place correctly to avoid failure. See Figures 2-0a and 2-0b.

c. Once locknut (F) is securely in place back up 2nd nut (D) to appropriate position. Tighten 1st nut (D) securely in

place on top of enclosure.

d. Thread 2nd lock washer onto carriage bolt.

e. Guide (2) mounting plates (E) onto threaded rod (G)

f. Thread 3rd lock washer (C) and 3rd nut (D) onto threaded rod (G)

g. Adjust mounting brackets to desired spacing and tighten nuts.

4. Remove desired knockout on back of enclosure and mount to junction box using hardware supplied with junction box.

5. Make electrical connections.

All electrical connections should be made inside the J-box.

Make electrical connection as follows: (Fig. 3-1)

Note: Cap unused leads to prevent shorting.

120VAC

White - Common

Black - 120V

Green - Ground

277VAC

White - Common

Orange - 277V

Green - Ground

Fig. 3-1a

White

(Neutral)

Black

(for 120V)

Orange

(for 277V)

Green

(Ground)

Black

(for 120V)

Green

(Ground)

6. Flip cover up and re-secure using (2) 6-32 X 1/4“ screws.

7. Open battery cover by turning thumb screw counter clockwise.

8. Connect battery as shown then secure connector at bottom left corner of compartment (Fig. 4-1 ).

9. Close door and secure with thumb screw.

Standard Operation Instructions

1. Energize un-switched AC power to unit

2. Verify indicator LED or numeric display is illuminated

3. Press test button and verify lamps turn on

Note: If lamps do not illuminate, allow unit to charge for 30 min

4. Leave AC connected for rated charge time prior to performing any full-length test

5. Refer to section (Self-Test/Self-Diagnostics) for operation.

SCL Series

Installation Instructions

10070159 REV 5 - 09/19 3 800-533-3948 www.barronltg.com

Fig. 4-1

Battery Connection

Knurled Thumb

Screw

Battery

SCL Series

Installation Instructions

10070159 REV 5 - 09/19 4 800-533-3948 www.barronltg.com

SELF-TEST/SELF-DIAGNOSTIC

OPERATING INSTRUCTIONS

KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE

I M P O R T A N T: Once all emergency lamps have been connected to the unit equipment, apply normal AC power and

charge for 24 hours.

For units equipped with G2 and the tri-color LED indicator: Following installation and after AC power has been supplied,

charge for 48 hours, then press and hold the test button until the LED indicator turns orange. This calibrates the unit

equipment for the proper load.

Operation

The purpose of this option is to provide Self-testing and Self-diagnostic capabilities to the unit equipment. At

predetermined intervals, the unit equipment will automatically switch into battery mode. The unit equipment will also

perform various Self-diagnostic tests of the unit. Visual signaling will alert maintenance personnel to a fault of the unit

equipment electronics, emergency lamp(s), battery and/or battery charger. The circuitry continuously monitors the

operating condition of the unit equipment and battery charging circuit/battery supply voltage. Refer to Table 1 for units

equipped with a tri-color LED indicator. Refer to Table 2 for units equipped with a numeric indicator.

Self-Test Features

• The unit equipment will automatically switch to battery mode every 28 days for a period of 1 minute.

• The unit equipment will automatically switch to battery mode every 6 months for a period of 90 minutes.

Manual Test Features

• Press the TEST BUTTON momentarily for a 2 second test. (tri-color LED unit only)

• Press the TEST BUTTON until the LED turns ORANGE or the numeric indicator shows “7” for a manual 1 minute test.

• Press the TEST BUTTON until the LED flashes RED/GREEN, (tri-color LED unit only) for manual 90 minute test.

LED Indication

Steady

Pulse

Steady

Pulse

Steady

Pulse

LED Color

Green

Red

Orange

Red/Green

Unit Condition

Float Charge

Hi-Rate Charge

Low Batt Voltage

Emer Lamp Failure

No AC Power

Charge Failure

1 Minute Test

Batt Disconnected

90 Minute Test

Comment

Batt Fully Charged

Batt Under High-Rate Charge

Replace Battery

Check AC Connection

Replace Transformer

1 Min Test Every 28 Days

Check Batt Connections

90 Min Test Every 6 Months

Replace Damaged or

Missing Lamps

Table 1 - Tri-Color LED Indicator

CHARGED

0 Float charging

CHARGING 1 Hi rate charging

EM/BATT 2 Discharging

CHRG FAIL

3 Charger failure

DISC BATT

4 Battery not connected

LAMP FAIL 5 Lamp failure

LOW BATT 6 Low battery voltage

1 MIN TEST 7 Manual testing

90 MIN TEST 8 Self testing

STATUS LEDGE Condition

Table 2 - Numeric Indicator

Bottom of Unit

Numeric Indicator

Tri-Color LED

Table des matières

Autres manuels BARRON Équipement d'éclairage

BARRON

BARRON Trace-Lite AXL2 Manuel utilisateur

BARRON

BARRON Exitronix 400U Series Manuel utilisateur

BARRON

BARRON Exitronix TPXC Series Manuel utilisateur

BARRON

BARRON specialityLED RFX Manuel utilisateur

BARRON

BARRON EXITRONIX 400WX Series Manuel utilisateur

BARRON

BARRON CP-EMW Series Manuel utilisateur

BARRON

BARRON Speciality LED FBTCJ-24V Manuel utilisateur

BARRON

BARRON Exitronix NY900C Series Manuel utilisateur

BARRON

BARRON Exitronix CRL Series Manuel utilisateur

BARRON

BARRON TL301 Manuel utilisateur

BARRON

BARRON TRACE-LITE WTA Series Manuel utilisateur

BARRON

BARRON EXITRONIX VLEDC Series Manuel utilisateur

BARRON

BARRON EXITRONIX LED-51 Series Manuel utilisateur

BARRON

BARRON Exitronix VEX-8 NEMA Manuel utilisateur

BARRON

BARRON TRACE-LITE RHL-ACR Manuel utilisateur

BARRON

BARRON Exitronix S900C Series Manuel utilisateur

BARRON

BARRON Exitronix LED-90 Series Manuel utilisateur

BARRON

BARRON Trace-Lite E110 Manuel utilisateur

BARRON

BARRON EXITRONIX CRL Series Manuel utilisateur

BARRON

BARRON specialtyLED FTK Manuel utilisateur

BARRON

BARRON EXITRONIX ILX Series Manuel utilisateur

BARRON

BARRON Growlite GLB-315-A-120/277 Manuel utilisateur

BARRON

BARRON EXITRONIX VLED-90L Series Manuel utilisateur

BARRON

BARRON GROWLITE GRM Manuel utilisateur

Manuels Équipement d'éclairage populaires d'autres marques

Brizo

Brizo 8SP-MU-4 Manuel utilisateur

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manuel utilisateur

IKEA

IKEA BJÖRKSPIREA Manuel utilisateur

Laserworld

Laserworld Evolution Series ES-400RGB Manuel utilisateur

Alien

Alien RG STAR Manuel utilisateur

EuroLite

EuroLite LED B-40 Manuel utilisateur

Qazqa

Qazqa Suplux SL 3 Black 103062 Manuel utilisateur

Commercial Electric

Commercial Electric 54568141 Manuel utilisateur

CREE LIGHTING

CREE LIGHTING 304 Series Manuel utilisateur

Goobay

Goobay 49867 Manuel utilisateur

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manuel utilisateur

Alkalite

Alkalite Krypton KT-81 Manuel utilisateur

Clas Ohlson

Clas Ohlson GU10 Manuel utilisateur

DTS

DTS DELTA 10 F Manuel utilisateur

ring

ring Solar Steplight Manuel utilisateur

One Stop Gardens

One Stop Gardens 57696 Instructions de montage

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manuel utilisateur

SIREM

SIREM Swimeo A2 Manuel utilisateur