BARRON Exitronix LED-90 Series Manuel utilisateur

LED-90 SERIES

INSTALLATION INSTRUCTIONS

800.533.3948 •www.barronltg.com

10070145 Rev 1 - 03/14 1

SAVE THESE INSTRUCTIONS!

READ CAREFULLY AND FOLLOW ALL INSTRUCTIONS FOR YOUR OWN SAFETY

• DISCONNECT AC POWER SUPPLY BEFORE SERVICING.

• Installation and servicing of this equipment should be performed by qualified service personnel only.

• Ensure the electricity connections conform to the National Electrical Code and local regulations if applicable.

• Do not mount near gas or electrical heaters.

• Equipment should be mounted in locations and at heights where it will not readily be subjected to tampering by

unauthorized personnel.

• The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition. Any

modification or use of non-original components will void the warranty and product liability.

• Do not use this equipment for other than intended use.

INSTALLATION INSTRUCTIONS

JUNCTION BOX / WALL CEILING MOUNT

1. Remove backplate by pushing through the two tabs at the bottom using a narrow screwdriver.

2. Feed fixture leads through backplate.

3. All Electical connections should be made inside junction box.

Make Electrical Connections as follows:

Note: Cap unused leads to prevent shorting.

4. Mount backplate to junction box using hardware provided with junction box.

5. Connect battery only after continuous AC power can be provided to the unit.

6. Align tabs and push housing directly onto backplate.

120V AC

White - Common

Black - 120V

Green - Ground

277V AC

White - Common

Orange - 277V

Green - Ground

Use Flexible Conduit Only.

LED-90 SERIES

INSTALLATION INSTRUCTIONS

800.533.3948 •www.barronltg.com

10070145 Rev 1 - 03/14 2

CONDUIT MOUNT

1. Remove backplate by pushing through the two tabs at the bottom using a

narrow screwdriver.

2. Mount backplate to wall surface using keyhole knockouts.

3. Use conduit entry knockouts on backplate and the unit’s housing to

secure conduit.

4. Route fixture leads through hole in conduit flange.

5. All Electrical connections should be made inside junction box.

Make Electrical Connection as follows:

Note: Cap unused leads to prevent shorting.

6. Connect battery only after continuous AC power can be provided to the

unit.

7. Align tabs and push housing directly onto backplate.

OPERATION

1. During and electrical power failure, the LED lamps will automatically

come on for a minimum of 90 minutes.

2. To test, depress the “TEST” switch. The emergency LED lamps will

illuminate. When the switch is releasedthe lamps will go off.

TESTING

The battery supplied with this unit requires no maintenance. However, it should be tested periodically and replaced when

it no longer operates the lamp heads for the duration of 30 seconds. The battery in this unit has a life expectancy of 4

years when used in a normal ambient temperature of 72°F.

Conduit Entry Keyhole Knockouts

Unit

Connector

Locking Tabs

Conduit Entry Knockout

CHARGER

BOARD

277V RED

120V BLACK

0V WHITE

YELLOW (+)

BLUE (-)

YELLOW (+)

BLUE (-)

LAMP

TEST

READY

RED

BLACK

BATTERY

WIRING DIAGRAM

NOTE: Unused input

lead must be properly

insulated with wire nut

or other approved

method.

120V AC

White - Common

Black - 120V

Green - Ground

277V AC

White - Common

Orange - 277V

Green - Ground

Table des matières

Autres manuels BARRON Équipement d'éclairage

BARRON

BARRON specialityLED RFX Manuel utilisateur

BARRON

BARRON EXITRONIX ILX Series Manuel utilisateur

BARRON

BARRON TRACE-LITE TL101 Manuel utilisateur

BARRON

BARRON EXITRONIX 82 Series Manuel utilisateur

BARRON

BARRON EXITRONIX VLEDC Series Manuel utilisateur

BARRON

BARRON Exitronix 400U Series Manuel utilisateur

BARRON

BARRON Exitronix 900E Series Manuel utilisateur

BARRON

BARRON Exitronix NY900C Series Manuel utilisateur

BARRON

BARRON EXITRONIX 400WX Series Manuel utilisateur

BARRON

BARRON EXITRONIX LED-51 Series Manuel utilisateur

BARRON

BARRON Exitronix NFT Series Manuel utilisateur

BARRON

BARRON Trace-Lite E110 Manuel utilisateur

BARRON

BARRON GROWLITE GRM Manuel utilisateur

BARRON

BARRON TRACE-LITE RHL-ACR Manuel utilisateur

BARRON

BARRON TRACE-LITE WTA Series Manuel utilisateur

BARRON

BARRON CP-EMW Series Manuel utilisateur

BARRON

BARRON Exitronix CRL Series Manuel utilisateur

BARRON

BARRON Exitronix VEX-8 NEMA Manuel utilisateur

BARRON

BARRON Growlite GLE-GL Manuel utilisateur

BARRON

BARRON specialtyLED FTK Manuel utilisateur

BARRON

BARRON Exitronix NFT Series Manuel utilisateur

BARRON

BARRON EXITRONIX SCL Series Manuel utilisateur

BARRON

BARRON Exitronix S900C Series Manuel utilisateur

BARRON

BARRON EXITRONIX CRL Series Manuel utilisateur

Manuels Équipement d'éclairage populaires d'autres marques

Brizo

Brizo 8SP-MU-4 Manuel utilisateur

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manuel utilisateur

IKEA

IKEA BJÖRKSPIREA Manuel utilisateur

Laserworld

Laserworld Evolution Series ES-400RGB Manuel utilisateur

Alien

Alien RG STAR Manuel utilisateur

EuroLite

EuroLite LED B-40 Manuel utilisateur

Qazqa

Qazqa Suplux SL 3 Black 103062 Manuel utilisateur

Commercial Electric

Commercial Electric 54568141 Manuel utilisateur

CREE LIGHTING

CREE LIGHTING 304 Series Manuel utilisateur

Goobay

Goobay 49867 Manuel utilisateur

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manuel utilisateur

Alkalite

Alkalite Krypton KT-81 Manuel utilisateur

Clas Ohlson

Clas Ohlson GU10 Manuel utilisateur

DTS

DTS DELTA 10 F Manuel utilisateur

ring

ring Solar Steplight Manuel utilisateur

One Stop Gardens

One Stop Gardens 57696 Instructions de montage

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manuel utilisateur

SIREM

SIREM Swimeo A2 Manuel utilisateur