Baridi DH115 Manuel utilisateur

Baridi 6L Beer Keg Dispenser Tap with

Integrated Cooling

Model No. DH115

Thank you for purchasing a Baridi product from the Dellonda range. Manufactured to a high standard,

this product will, if used according to these instructions, and properly maintained, give you years of

trouble free performance.

DH115.V1 Issue 2 16/12/2022

Important Information

Please read these instructions carefully and note any safe operational requirements, warnings &

cautions. Use the product correctly and with care for the purpose for which it is intended. Failure

to do so may cause damage and/or personal injury and will invalidate the warranty. Keep these

instructions safe for future use.

• ELECTRICAL SAFETY

• WARNING! It is the user’s responsibility to

check the following:

• Check all electrical equipment and appliances

to ensure that they are safe before using.

Inspect power supply leads, plugs and

all electrical connections for wear and

damage. Baridi recommend that an RCD

(Residual Current Device) is used with all

electrical products.

• if the product is used in the course of business

duties, it must be maintained in a safe

condition and routinely PAT (Portable

Appliance Test) tested.

• Electrical safety information. It is important

that the following information is read and

understood.

• Ensure that the insulation on all cables and on

the appliance is safe before connecting it to

the power supply.

• Regularly inspect power supply cables and

plugs for wear or damage and check all

connections to ensure that they are secure.

• Important: Ensure that the voltage rating on

the appliance suits the power supply to be

used and that the plug is tted with the

correct fuse - see fuse rating in these

instructions.

• DO NOT pull or carry the appliance by the

power cable.

• DO NOT pull the plug from the socket by the

cable. Remove the plug from the socket by

maintaining a rm grip on the plug.

• DO NOT use worn or damaged cables, plugs

or connectors. Ensure that any faulty item is

repaired or replaced immediately by a

qualied electrician.

• This product is tted with a BS1363/A 3 pin

• plug.

• If the cable or plug is damaged during use,

switch off the electricity supply and remove

from use.

• Replace a damaged plug with a BS1363/A

3 pin plug. If in doubt contact a qualied

electrician.

• Class II products are wired with live (brown)

and neutral (blue) only and are marked with

the Class II symbol;

• A) Connect the BROWN live wire to the live

terminal ‘L’.

• B) Connect the BLUE neutral wire to the neutral

terminal ‘N’.

• C) After wiring, check that there are no bare

wires and ensure that all wires have been

correctly connected.

• Ensure that the cable outer sheath extends

inside the cable restraint and that the restraint

is tight.

• DO NOT connect either wire to the earth

terminal.

• Dellonda recommend that repairs are carried

out by a qualied electrician.

Replacement fuse rating:

Refer to

instructions

Indoor use

only

• GENERAL SAFETY

• DO NOT remove keg until fully empty.

• DO NOT cover the unit while working.

• DO NOT place in direct sunlight.

• WARNING: Ensure the supply cord is not

trapped or damaged.

• Alcohol should not the consumed by any

person who is not of a legal age to do so.

• Children should be supervised at all times

around this equipment.

• INTRODUCTION

• A 6L keg Beer Dispenser with a stay fresh 30

day digital countdown. It can chill beer to as

low as 3°C and has a handy LED temperature

gauge along with being quiet to use.

Compatible for use with over 40 x 6L mini beer

kegs and operated by air pump, so no need

for gas cylinders. Containing a handy level

indicator on the display showing the amount

of beer left in the keg. With a removable drip

tray to help keep your home bar area clean and

tidy. With a retro black and chrome home bar

design.

• SPECIFICATION

• Model no: DH115

• Lowest temperature: 3°C

• Voltage: 230V

• Frequency: 50Hz

• Foaming Gas: Cyclopentane

• Noise level: ≤48dB(A); Ambient noise ≤25dB(A)

• Dimensions (W x D x H): 495 x 290 x 476mm

• Keg capacity: 6L (Universal Style only)

• LOCATION

• DO NOT locate the unit in a damp or moist

location.

• Operate unit on dry and level surface.

• NOTE: The unit is designed to be free-standing

and to ensure adequate ventilation, leave at

least 12 cm free space around the unit.

• Once in position allow the unit to rest for an

hour before turning it on.

• NOTE: Allow beer to fully settle before

attempting to t dispensing unit.

• NOTE: DO NOT leave keg standing in direct

sunlight or near a heat source.

• NOTE: It is recommended that you allow the

keg to cool for some time before use (ideally

have it pre chilled if possible).

• NOTE: Carefully read any information

provided by the beer manufacturer that

relates to the keg and its operation.

• If tted, remove keg safety clasp according to

keg manufacturers instructions.

1 Handle for top cover

2 Top cover

3 Beer out connector

4 Keg

5 Tap

6 LED Display

7 Digital control button

8Drip tray

9 Power switch

10 Rear cover

11 Connection valve

12 Air in connector

Fig.1

• Connect the air delivery hose of the air

connection valve (g.1.11, g.4) to the air-in

connector (g.1.12, g.4).

• OPERATION

• Read this document thoroughly and assemble

the unit accordingly.

• Check that the unit is fully assembled and

installed in the appropriate location.

• When the unit is switched on, the LED is

activated.

• NOTE: To cool a beer keg to 3oC may take up

to 20 hours depending on initial beer temp

and ambient temp.

• The unit has a temperature setting range of

between 3oC and 12oC.

• The interface (g.5) will show the current

beer temperature and number of days the

beer keg has been tted.

• To set a required beer temperature use the ‘+’

or ‘-’ key (g.6) to set the value.

• To display the current set value, press the ‘-’

button for one second. The display will return

to the current beer temperature after three

seconds.

• NOTE: The unit has a memory function that

uses the last selected temperature.

• To adjust the number of days use the keg

has had press and hold either the “+” or “-”

symbol .

•

• BEER DISPENSING UNIT (g.2)

• Assemble and t the beer dispensing unit

(g.2) as follows:

• Screw the handle to tap unit.

• Thread the clear hose of the beer-out

connector through the removable cover of the

tap unit (g.3).

• Pull the handle forward to the open position

(g.3) and slide the clear hose of the beer-out

connector rmly onto the inlet spigot in the tap

unit. When the handle is released it will shut

off the ow of beer.

• Locate the assembled dispensing unit (g.2)

into the body of the unit. Fix in place using the

supplied screws and place the rubber covers

over the exposed xings.

•

Temperature

Days Fitted

Fig.2

Fig.3

Fig.4

Fig.5

Fig.6

• For more soiled surfaces use a neutral

detergent, wipe down with a clean damp cloth

and dry thoroughly with a clean dry cloth.

• CLEANING AND MAINTENANCE

• Remove the power plug from the supply when

performing cleaning or maintenance.

• It is recommended to empty the drip tray

frequently

• Cleaning the internals of the unit is imperative

to meet hygiene requirements. Clean before

rst use or long periods of non-use.

• Clean all internals ONLY with warm, clean

water.

• Cleaning the unit when changing kegs of

di󰀨erent beers is also recommended to

improve your drinking experience.

• DO NOT use abrasive or chemical cleaning

materials on any surface of the unit.

• Wipe interior and exterior surfaces with a

damp cloth and dry thoroughly with a clean

dry cloth.

• TROUBLESHOOTING

Symptom Possible cause Possible solution

Unit does not

operate

Not plugged in. Check connection and fuse

Keg has low/no content Check keg

Faulty liquid and air connections Check all tubes connected

Beer is frothing Check beer temperature Cool keg

Keg has low/no content Check keg

Tap opened too quickly Slower delivery

Environment Protection, Waste Electrical and Waste

Electronic Equipment Regulations (WEEE)

Recycle unwanted packaging materials. When this product is no longer required, or has

reached the end of its useful life, please dispose of in an environmentally friendly way.

Drain any uids (if applicable) into approved containers, in accordance with local waste

regulations. Please note that this product contains one or more batteries. It is our policy to

continually improve products and we reserve the right to alter data, specications and parts

without prior notice. No liability is accepted for incorrect use of this product. Guarantee is

12 months from purchase date, proof of which is required for any claim.

Dellonda Limited, Sole UK Distributor of Baridi

Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR

01284 757575 [email protected] www.dellonda.co.uk

Manuels Distributeur populaires d'autres marques

Silver King

Silver King Majestic SK12MAJ Guide de démarrage rapide

Franke

Franke F3Dn Twin Manuel utilisateur

STIEBEL ELTRON

STIEBEL ELTRON UltraHot Plus Manuel utilisateur

DAN DRYER

DAN DRYER 282 Manuel utilisateur

Essity

Essity Tork 473208 Manuel utilisateur

CBS

CBS SD300BU-88 Guide de configuration

Sealey

Sealey MK77 Manuel utilisateur

Fluid Management

Fluid Management Accutinter 1600 Manuel utilisateur

Franke

Franke DVS SD99-010 Manuel utilisateur

Graco

Graco Dispensit 1053-10C Guide de dépannage

ITALTINTO

ITALTINTO i50 Manuel utilisateur

Coca-Cola

Coca-Cola FREESTYLE 9000 Manuel utilisateur

Graco

Graco ProMix 2KE Mode d’emploi

TECHCON SYSTEMS

TECHCON SYSTEMS TS1251 Manuel utilisateur

Wayne

Wayne GLOBAL VISTA CNG Manuel utilisateur

clarsen

clarsen H133 Manuel utilisateur

PicoBrew

PicoBrew Zymatic Manuel utilisateur

BOWMAN

BOWMAN BP-007 Manuel utilisateur

baridi DH115 Manuel utilisateur

Manuels Distributeur populaires d'autres marques